12-0118 (SOTB)P.O. BOX 1504
78-495 CALLE TAMPICO
LA QUINTA, CALIFORNIA 92253
Application Number: 12-001000.118
Property Address: 81943 PRISM DR
APN:. 764 -360 -048 -
Application description: STRUCTURES OTHER THAN BUILDING
Property Zoning: MEDIUM HIGH DENSITY RES
Application valuation: 20000
Applicant: Architect or Engineer:
_al a
-----------------
LICENSED CONTRACTOR'S DECLARATION
BUILDING & SAFETY DEPARTMENT
BUILDING PERMIT
I hereby affirm under penalty of perjury that I am licensed under provisions of Chapter 9 (commencing with
Section 7000) of Division 3 of the Business and Professionals Code, and my License is in full force and effect.
License Class: �wB License No.: 4 8 7 8 9 7
'V 00/ Date: 3 ontractor: n
OWNER -BUILDER DECLARATION
I hereby affirm under penalty of perjury that I am exempt from the Contractor's State License Law for the
following reason (Sec. 7031 .5, Business and Professions Cade: Any city or county that requires a permit to
construct, alter, improve, demolish, or repair any structure, prior to its issuance, also requires the applicant for the
permit to file a signed statement that he or she is licensed pursuant to the provisions of the Contractor's State
License Law (Chapter 9 (commencing with Section 7000) of Division 3 o the Business and Professions Code) or
that he or she is exempt therefrom and the basis for the alleged exemption. Any violation of Section 7031.5 by '
any applicant for a permit subjects the applicant to a civil penalty of not more than five hundred dollars ($500).:
(_) I, as owner of the property, or my employees with wages as their sole compensation, will do the work, and
the structure is not intended or offered for sale (Sec. 7044, Business and Professions Code: The
Contractors' State License Law does not apply to an owner of property who builds or improves thereon,
and who does the work himself or herself through his or her own employees, provided that the '
improvements are not intended or offered for sale. If, however, the building or improvement is sold within
one year of completion, the owner -builder will have the burden of proving that he or she did not build or
improve for the purpose of sale.).
I ' 1 I, as owner of the property, am exclusively contracting with licensed contractors to construct the project (Sec.
7044, Business and Professions Code: The Contractors' State License Law does not apply to an owner of
property who builds or improves thereon, and who contracts for the projects with a contractor(s) licensed
pursuant to the Contractors' State License Law.).
( 1 I am exempt under Sec. , B.&P.C. for this reason .
Date:
Owner:
. CONSTRUCTION LENDING AGENCY
I hereby affirm under penalty of perjury that there is a construction lending agency for the performance of the
work for which this permit is issued (Sec. 3097, Civ. C.).
Lender's Name: '
.Lender's Address: .
VOICE (760) 777-7012
FAX (760) 777-7011
INSPECTIONS (760) 777-7153
Date: 3/01/12
Owner:
JOE & SANDY RAITI
81943 PRISM.DRIVE
LA QUINTA, CA'92253
Contractor:
THOMAN WOODWORKS, SHAWN
6323 HARDWICK-STREET
LAKEWOOD, CA 90713
(562)925-6340
Lic. No.: 487897
WORKER'S COMPENSATION DECLARATION
I hereby affirm under penalty of perjury one of the following declarations:
I have and will maintain a certificate of consent to self -insure for workers' compensation, as provided
for by Section 3700 of the Labor Code, for the performance of the work for which this permit is
issued.
I have and will maintain workers' compensation insurance, as required by Section 3700 of the Labor
Code, for the, performance of the work for which this permit is issued. My workers' compensation
insurancecarrierand policy number are:
Carrier EXEMPT Policy Number EXEMPT .
I. certify that, in the performance of the work for which this permit is issued, I shall not employ any
person in any manner so as to become subject to the workers' compensation laws of California,
and agree that, if I should become subject to the workers' compensation provisions of Section
y,, 370 the Labor Co e, I shall com�ith those Provisions.
/.ate:. W � pplicant: �N M , Iios
WARNING: FAILURE TO SECURE WORKERS' COMPENSATION COVERAGE IS UNLAWFUL, AND SHALL
SUBJECT AN EMPLOYER TO CRIMINAL PENALTIES AND CIVIL FINES UP TO ONE HUNDRED THOUSAND
DOLLARS ($100,000). IN ADDITION TO THE COST OF COMPENSATION, DAMAGES AS PROVIDED FOR IN
SECTION 3706 OF THE LABOR CODE, INTEREST, AND ATTORNEY'S FEES.
APPLICANT ACKNOWLEDGEMENT
IMPORTANT Application is hereby made to the Director of Building and Safety for a permit subject to the
conditions and restrictions set forth on this application.
1. Each person upon whose behalf this application is made, each person at whose request and for
whose benefit work, is performed under or pursuant to any permit issued as a result of this application,
the owner, and the applicant, each agrees to, and shall defend, indemnify and hold harmless the City
of La Quinta, its officers, agents and employees for any act or omission related to the work being
performed under or following issuance of this permit.
2. Any permit issued as a result of this application becomes null and void if work is not commenced
within 180 days from date of issuance of such permit, or cessation of work for 180 days will subject
permit to cancellation.
I certify that I have read this application and state that the above information is correct. I agree.to comply with all
city and county ordinances and state laws relating to building construction, and hereby authorize representatives
gt this county to enter upon the above-mentioned prpartyXB **nspection p oses��/%
Date: 3 a Signature (Applicant or Agent): /[/ Ly_�
Application Number . . . 12-00000118
Permit . . . BUILDING PERMIT
Additional desc .
Permit Fee . . . . 207.00
Plan Check
Fee
134.55
Issue Date . . . .
Valuation
. . .
. 20000
Expiration Date 8/28/12
Qty Unit Charge Per
Extension
BASE FEE
45.00
18.00 9.0000 THOU BLDG 2,001-25,000
-------------------------------------------.--
-------------------------------
162.00
Permit . . . ELEC-MISCELLANEOUS
Additional desc .
Permit Fee . . . . 15.00
Plan Check
Fee
3.75
Issue Date
Valuation
. . .
. 0
Expiration Date 8/28/12
Qty Unit Charge Per
Extension
BASE FEE
----------------------------------------------------------------------------
15.00
Permit . . . PLUMBING
Additional desc..
Permit Fee . . . . 18.00
Plan Check
Fee
4:50
Issue Date . . . .
Valuation
0
Expiration Date .. 8/28/12
Qty Unit Charge Per
Extension
BASE FEE
15.bo'
1.00 3.0000 EA PLB GAS PIPE
1-4 OUTLETS
3.00
----------------------------------------------------------------------------
Special Notes and Comments
INSTALLATION OF INTERIOR DIRECT VENT
FIREPLACE (SPARKFIRE RIBBON 3 ST)- &
CABINETRY. INSTALLATION MANUAL TO BE
AVAILABLE TO INSPECTOR DURING
INSPECTION. 2010 CODES
----------------------------------------------------------------------------
Other Fees . . . . . . . . BLDG STDS ADMIN (SB1473)
1.00
ENERGY REVIEW FEE
13.46
Fee summary Charged Paid
--------------------
Credited
--------------------
Due
-----------------
Permit Fee Total 240.00
.00 ..00
240.00
Plan Check Total 142.80
.00
.00
142.80
-Other Fee Total 14.46
.00
.00
. 14.46
Grand'Total 397.26
.00
.00
397.26
LQFEXA11T
B,R:#
Permit #
ProjectAddress: ��
City. of La Quints
BAft 8c Safety Division.
P.O. Box 1504,"76-495 Calle Tampico
[a.Quinta, CA 92253 - (760) 777-7012
Building Permit Application and Tracking Sheet
3 % 1 sigh Owner's Name:. V/- /KAO SNAJQ1
A. P. Number.
Address: .947 7 3 / IT I•f
Legal Description:
City, ST, Zip: L,& a A) S3
Contractor. 5 A(t f &W 7WO)ROJ
Telephone:' 0 • 7,7,-10
Address: 713 tM�40jlg6 "
Project Description: /NS72ftl, 7,6&(� CG6UA,/t-it/
City, ST, Zip: 1 -Ur -00010 ew. • ?071,3ri!
MGE 64R17G1AArGf %(
Telephone: 310.7ed -
00
"'CityLic,Ak-
�i �l/V1�Z�T . wit 10CCOARTNE.
$rr0 NF $1.�t211.�U .
State Lie. #: '' 6
/09+/
Arch., Eng., Designer
Address:
City., ST, Zip:
Telephone:
State Lic. #:
'
Construction Type:..W. F. Occupancy: S. F.
Project type (circle one): New Add'n Alter Repair Demo
Sq. Ft : # Stories: # Units:
Name of Contact Person:
S,440L0 7�. �
Telephone # of Contact Person: 31 0 -7BD • P1
Estimated Value of Project;
# Submittal
APPLICANT. DO NOT WRITE BELOW THIS UNE
Req'd Recd TRACMG PERMITFEFS'
Plan Sets
Plan Cheek submittedItem Amount
Structural Cales.
Reviewed, ready for correcd1us Plan Check Deposit...
Truss Calks.
Called Contact Person Plan Check Balance
Title 24 Cates.
Plans picked up Construction "
Flood ptafuplan
Plans resubmitted.' .yy.� Mechanical
Grading plan
V Review, ready for correc6o Issue V t Electrical
Subeoatattor list
Called Contact Person Plumbing
Grant Deed
Plans picked up S M,L
H.O.A. Approval
Plans resubmitted Grading "
IN HOUSE.-
'j° Review; ready for eormcdons/issuc Developer Impact Fee
Planning Approval.
Called Contact Person A.I.P.P. "
Pub. Wks. Appr
Date of permit Issue
'
School Feesp.
Total Permit Fees r r-7. u0
CONSTRUCTION HOURS
October 1st - April 30
Monday - Frida8:00-a mato 5 OO .
:30 pmm.
Saturday:
Sunday: None
None
s:
Government Code Honda y h
May 1st - September 30th Wn �}
Monday - Friday: :00:a.0 to 5:00 -p.m. 0(
Saturday:
Sunday: None K k
Government Code H ays: None., _ � a 4Ll�
a IL I I Gt{N �,l v
(JyN19`ir � �
Construction is NOT
RMMED
on the following Code lidays: _o
New Year's Day _ _ �� Q
Dr. Martin Luther King Jr. ay' / �_ _ _ _ I �
President's Day 1 y
Memorial Day // I oE�- ` a
Independence y
Day
I I .
Labor Da � •, ; .
.0 '� .3
Veteran's Day I z ; •. _
Thanksgiving Day }`
Christmas Day —
�E
EEE OF $30 I o n O
-INSPECTION ROVEO I W
A RE J ' j
ILL 8E CHARGED 1F.WE AP N®T ON _ �: C1
V4 RD ARE � I
PLANS AND 108 CA d
ITE FOR A gCHEOULEO s PrLoPosig0 I ON
THE SON. F►n,f t'T-h� — oil 2
INSPECTI DNS! O Z C
NO EXCEP`N �
j = 9
<0
u.'
m C�
I i
CV
CD C_j�
O Z Cr_WLA-1=
_W Q O = LL -
AJ
LIN LL_
LLJ
r-iW Q O2 ii 4
W -a: (J, W
O O W W S
F'- U Z
Q WO Q 1---LLJ ~Q
<.Q = Cn cm _ M
OC�f W W Q W--
Z� Q d r�
¢. W C=)
O
CITY OF LA QUINTA '
BUILDING & SAFETY DEPT.
APPROVED
FOR CONSTRUCTION
DATE 13 .
_ Y
w
f
o
i
SPARK Fire Ribbon
Direct Vent 3 ft
Right Side view
32.125'
Electric
access
both
sides
Model No.
I
ki 1 36.125"1
�I�h
OS" I Gas fine access
22.5" ! both sides
Glass viewing area
Outer dimensions i
Gas type*
On/off*
Efficiency
Venting Options
Vent Type—
Fan
Electric;
BTU input
Doors/glass
Interior color` +
Certification
Options
"Must be specified at ti
of ordering. +
"Must source locally.
• Vent through the roof or exterior wall
• Up to 80% efficient
• Heating capacity enhanced with integrated fan
• Accepted by all major building and mechanical codes
in the U.S. including the IMC and the UMC
• Approved in all 50 states and Canada
• No draft concerns
Front view Top view
I 67
Does not require vertical venting.
36-W x 16'H
45'W x 36.125'H x 22.5'D
Natural or LP/propane
Remote control
Up to 80%
Through the roof or exterior wall
Simpson Duravent GS Pro 6 W diameter
Thermostat activated 160 c.f.m.
110 v.
19,000 - 28,000 BTU/h
Fixed ceramic glass panel
Satin Black
Omni -Test Laboratories
ANSI Z21.88-2009 CSA 2.33-2009
Safety Screen*
ne (Safety Screen is recommended for public installations)
Fire Objects and Media Tray*
(Tray required when using fire objects)
Add even more design to your fire—visit
www.sparktires.com to view our custom fire objects
Please consult manual for surround installation.
CITY OF LA QUINTA
BUILDING & SAFETY DEPT.
APPROVED
FOR CONSTRUCTION
DATE BY modern fires
r
Requires 3' vertical vent before any horizontal venting
36'W x 16'H
45'W x 36.125'H x 22.5'D
Natural or LP/propane
Remote control
Up to 800
Through side wall or roof
Simpson Duravent GS Pro 6 W diameter '
Thermostat activated 160 c.f.m.
110 V.
28,000 - 35,000 BTU/h
Fixed ceramic glass panel
Satin Black
Omni -Test Laboratories
ANSI Z21.88-2009 CSA 2.33-2009
Safety Screen*
(Safety Screen is recommended for public Installations)
Fire Objects and Media Tray*
(Tray required when using fire objects)
Spark Modern Fires
99B Greenwood Avenue I Bethel, CT 06801
www.sparkfires.com p. 866.938.3846
PRODUCT SPECIFICATIONS
• This appliance has been certified
for use with either natural or
propanegas. See appropriate data
plates. 4
• This applianE is not for use with
solid fuels.
• The appliance is approved for bed-
room or bedsitting room installa-
tions.
• The appliance must be installed in
accordance with local codes if any.
If none exist uL a the current instal-
lation code. ANSI Z223.1/NFPA
54 in the USA, CAN/CGA B149
in Canada.
• This appliance is mobile home
approved. €
i
• The appliance must be properly
connected to a venting system.
4
• The appliance is not approved for
closet or recesls ed installations.
i
FIREPLACE CONTROLS (see Figure 1)
1 - Hi/Lo Knob
2 - Off/Pilot/On Knob
3 - Remote Control Receiver (optional)
4 - Blower Speed Control
5 - Blower
6 -Duplex Outlet for Blower (located against lower right outside wall)
CODE APPROVAL
Direct Vent type appliances draw all combustion air from outside of the dwelling through the vent pipe.
These appliances have been tested by OMM Test Labs and found to comply with the established standards for DIRECT VENT
GAS FIREPLACE HEATERS in the USA and Canada as follows:
} LISTED VENTED GAS FIREPLACE HEATER
j TESTED TO: ANSI 221.88-2009/CSA 2.33-2009 STANDARDS
Firebox framing can be built before or after the appliance is set in place. Construct firebox framing following Figure 2 and the
chart below foryour specific installation requirements. See Figure 3 on Page 8 for firebox dimensions. The framing headers may
rest on the top of the firebox standoff.
I
The firebox may be installed directly on a combustible floor or raised on a platform of an appropriate height. When the firebox
is installed directly on carpeting, tile, or other combustible material, other than wood flooring, the firebox shall be installed on a
metal or wood panel extending the full width and depth of the enclosure.
IMPORTANT: The following must be taken into consideration if
you decide to cover over the fireplace face:
7�D%on t 611 Spaces around firebox wish insulation 1The covering material must be non combustible, maximum 3/4" thick.er materials. This could cause a fire.
2. Minimum outside dimensions of the material over the Facing are
46" x 36-1/4" (see Figure 2).
3. The inner opening in covering material must be minimum 36-1/2" wide, 18" tall and centered over the fireplace opening to allow
for glass door removal.
4. The cover should maintain an air gap of at least 1/8" between covering material and fireplace to allow for metal fireplace front
to expand and contractt during operation.
5. PLEASE NOTE: Natural stone products may react to heat by discoloring or cracking. Spark Modem Fires is not resposible for
any damages due to covering materials used. If tiles are to be applied covering the fireplace face, a layer of cement board must
be used as a subskrate.
COVERING FIREPLACE FACE
Im mnmusneu
GOMMATRU
INSIDE CHASE INSTALLATION
46"
comms
RECESSED INSTALLATION
i.25"
Figure 2 - Froming Dimensions
7
FIREPLACE 40CATIONI
Plan for the installation of your appliance. This includes determining where the unit is to be installed, the vent configuration to be
used, framing and finishing details, and whether any optional accessories (i.e. wall switch, or remote control) are desired.
Consult your local building code agency to ensure compliance with local codes, including permits and inspections.
The following fauors should be taken into consideration:
• Clearance to fide -wall, ceiling, woodwork, and windows. Minimum clearances to combustibles must be maintained.
• This fireplace may be installed along a wall, across a corner, or use an exterior chase. See Figure 4 for suggested locarions.
• Location should be out of high traffic areas and away from furniture and draperies due to heat from appliance.
• Never obstruct the front opening of the fireplace.
• Do not install in the vicinity where gasoline or other flammable liquids may be stored.
• Vent pipe routing. See Venting section found in this manual for allowable venting configurations.
• These units can be installed in a bedroom or bathroom. See National Fuel Gas Code ANSI Z233.1/NFPA 54 (current edition),
the Uniform Mechanical Code — (current edition), and Local Building Codes for specific installation requirements.
A Flat on'
B Cross C
C Island"
D Room E
E Fiat on
F Chase I
Y 7° Minin
Comer'
Figure 4 - Locating Gas fireplace
" Island (C) and room divider (D) installation is possible as long as the horizontal portion of vent system (X)
does not exceed 20'. See Installing Horizontal Termination Configuration on pages 18 and 19.
' When you install your fireplace in (D) room divider or (E) flat on wall corner positions (Y), a minimum of 6'
clearance must be maintained from perpendicular wall and front of fireplace.
9
INSTALLATION FOR VERTICAL TERMINATION
1. Determine theroute your vertical venting will take. If ceiling joist,
roof rafters or other framing will obstruct, the venting system, consider
an offset. See �gure 27 to avoid cutting load bearing members.
MOTE: Pay special attention to these installation instructions for
required clearances (air space) to combustibles when passing
through ceilings,', walls, roofs, enclosures, attic rafters, etc. Do
not pack airspaces with insulation. Also note maximum vertical
rise of the venting system and any maximum horizontal offset
limitations. Offsets must fall within the parameters shows in
Figure 10, page 16.
2. Set fireplace in Edesired location. Drop a line plumb down from the
ceiling to the position of the flue exit. Mark the center point where
the vent will penetrate the ceiling. Drill a small locating hole a this
6
point.
f
Drop a plumb line from the inside of the roof to the ceiling locat-
ing hole in the !ceiling. Mark the center point where the vent will
penetrate the roof. Drill a small locating hole at this point.
FLAT CEILING INSTALLATION
1. Cut a 91/2" (24~lmm) square hole in the ceiling using the locating
hole as a center point The opening should be framed to 91h"x91/2"
(241 mm x 2411nm) inside dimensions as shown in Figure 12, page
17 using framing lumber the same size as the ceiling joist. If the
area above the ceiling is an insulated ceiling or a room, nail firestop
from the top side. This prevents loose insulation from falling into
the required clearance space. See fagurr 28.Otherwise, install firestop
.below the framed hole. The firestop should be installed with no less
than three nails per side. See Figure 29.
2. Assemble the desired lengths of pipe and elbows necessary to reach
from the burnerjsystem flue up through the firestop. Be sure pipe and
elbow connections are fully twist -locked. See Figure 13, page 17.
R
3. Cut a hole in the roof using the locating hole as a center point.
(Cover any expi sed open vent pipes before cutting hole in roof).
The 91/2"x91/2" (241mm x 241mm) hole must be measured on the
horizontal. Actual length may be larger depending on the pitch of
the roof There, must be a 1" minimum clearance from the vent
pipe to combustible materials. (Insulation should be considered a
combustible material) Frame the opening as shown in Figure 12 on
page 17. f
c
Roof
lashing
i1bows
Figure 27 - Offset with Wall Shap and 45 Elbows
ninae
Figure 28- if area above is a room, Install firestop
above framed hole as shown
Hgure 29 - If area above is not a room, Install firestop
below framed hole as shown
Continued on next page
23
Only persons licensed to work with gas piping
may make the necessary gas connections to
this at)[Aance.
A manual shutoff valve must be installed upstream
of the appliance. Union tee and plugged 1/a"
NPT pressure tapping point should be installed
upstream of the appliance. See Figure 33.
NOTE : The gas line connection may be made using 1/2" rigid tubing or an approved flex connector. Since some
municipalities have additional local codes it is ahvays best to consult your local authorities and the current edition
of the National Fuel Gas Code ANSI2223.1, NFPA54. In Canada CANICGA-B 149 (1 or 2) Installation Code.
A listed manual shutoff valve must be installed upstream of the appliance. Union tee and plugged 1/8" NPT pressure tapping
point should be insured upstream of the appliance. See Figure 33.
1
IMPORTANT. • Install main gas valve (equipment shutoff valve) in on. accessible location. The main gas valve is for
fuming on or shutting off the gas to the fireplace.
Check your building codes for any special requirements for locat-
ing equipment shutoff valve to fireplaces. 0F±1 111 d us]
Apply pipe joint sealant lightly to male threads. This will prevent
excess sealant from going into pipe. Excess sealant in pipe could Use pipe joint sealant that is resistant to liquid
result in clogged burner system valves. petroleum (LP) gas.
We recommend that you install a sediment trap/drip leg in supply
line as shown in Figure 33. Locate sediment trap/drip leg where it is within reach for cleaning. Install in piping system between
fuel supply and burner system. Locate. sediment trap/drip leg where trapped matter is not likely to freeze. A sediment trap traps
moisture and contaminants. This keeps them from going into the. burner system gas controls. If sediment trap/drip leg is not
installed or is installed wrong, burner system may not run properly.
CSA Design -Certified Equipment Shutoff Valve
/ with 1/8" NPT Tap*
Approved Flexible Gas
Tee Joint I
Trap/Drip Leg Pipe Nipple
Cap ------_ 3•,
Figure 33 - Gas Connection
26
Natural Gas
From Gas Meter
(5" W.C. to 10.5" W.C. Pressure)
Propane/LP
From External Regulator
(11" W.C. to 13" W.C. Pressure)
CERTIFIED APPLIANCE
Models; 87N, 87P, 88N, 88P
Direct Vent Gas Fireplace Heaters
Date Issued: May 30, 2006
Project: 321-F-03-5
Issued to: Spark Modern Fires i
PO Box 608
Georgetown, CT 06829
Products listed to:
• ANSI 221.88-2005/CSA 2,33-2005, "Vented Gas Fireplace Heaters:"
:
FOR USE Ii;NA tJ1AIy,.GA
�Y•:l .fi.
o.del Num ,"
"M a�amuiri:.lri •ut Rate
--F:
�.A2? 0
�• �-::. ..,).c;.,. -... .•h...=7�15d:.:{..
,tis :h:i' _00
�.`k);';5
:lcti :r '•si`>':an EZi'
,ir:: xF.; -n::c:a'ay
35;00060{;•;':;:;-,
,.,;.:
FOR`US1v �?ITI�::pROPANE'`5�
.tea•;'` �,.:
Model`.N'umbe
::;.' Maxi«<<
mum fn ut Rates'.:;';°:, Miffiiriuir`IfiuE:Rate,:<�r
,..
'
_, •_:...
.......�.__. ......... a.:3.-._.......+..:...,.....:.V_e'Yr..(::'.�-'C.•f.;ai.ti:.::.....,.w.._._-.-u•�._w.�-.,._.,....:_...._...rR....,.w.='.:::i11:.',
The models listed above are eligible to bear the mark shown.
f- k -1
Tested & P
Beaverton
Listed By JffejfWOregon USA
J fi;& us
,..
OMNI -Test Latioratorles, mc..
Issued by: OMNI -Test Laboratories Inc.
5465 SW Western Avenue, Suite G
Beaverton, Oregon 97005"
Alava Smith,for Manager—'i n oorhees, Techifical Services Director
A current Product Documentation and Listing Agreement is required to maintain appliance listing.
OMNI -Test Laboratories, Inc. is accredited by the Standards Council of Canada and the American National Standards
Institute as a certification organization.
CLEARANCES TO COMBUSTIBLES
Follow these instructions carefully to ensure safe installation. Failure to follow instructions
exactly can create a fire hazard. .
The appliance cannot be installed on a carpet, file or other combustible material other
than wood flooring. If installed on carpet or vinyl flooring, the appliance shall be installed
on a metal, wood or noncombustible material panel extending full width and depth of
the appliance.
The fireplace face may be
completely covered with
any non-combustible ma-
terial. Allow clearance for
removal of front air panel
and glass door.
90" minimum
1i PA M "017 in ra 111 u
Minimum 7"
from both
side walls
Clearance to
Combustibles
Sides
0
Floor
0
Back
0.5"
Standoff
0"
Front
36'
cOMevSTIB�E
\ MgNTEC
Figure 6 - Clearances
12"
maximum
depth - /
MANTEL CLEARANCES
NOTE: The combustible area above the facing must not protrude more than 3/4" from the facing. If it does, it is
considered a mantel and must meet the mantel requirements listed in this manual.
FOR HORIZONTAL TERMINATION
Inside Corner Detail
❑v Vent Terminal
MINIMUM DISTANCES
® Air Supply Inlet
Area Where Terminals Not Permitted
Figure 8 - Horizontal Vent Termination Location
A = Clearance above the grade, a veranda, porch, deck, or balcony [*12" (305mm) minimum].
B = Clearance to window or door that may be opened [*12" (305mm) minimum]
C = Clearance to permanently closed window [*minimum 12" (305mm) recommended to prevent condensation on window]
D = Vertical clearance to ventilated soffit located above the terminal within a horizontal distance of two (2) feet (610mm) from
the centerline of the terminal [18" (457mm) minimum].
E= Clearance to unventilated soffits [12" (305mm) minimum]. Clearance to vinyl soffit [30" (762mm)].
F = Clearance co an outside corner [*6" (152mm) minimum].
G = Clearance to an inside corner [*6" (152mm) minimum ]
H = *Nor to be installed above a gas meter/regulator assembly within three (3) feet (914mm) horizontally from the centerline of
the regulator.
I = Clearance to service regulator vent outlet [*3' (914mm) minimum].
J = Clearance to non-mechanical air supply inlet to building or the combustion air inlet to any other appliance [*12"
(305mm)minimum].
K= Clearance to a mechanical air supply inlet [*6' (18296hm) minimum].
L = Clearance above a paved sidewalk or paved driveway located on public property ["*7' (2133mm) minimum].
M = Clearance under veranda, porch, deck, or balcony [*12" (305mm) minimum-].
N = Clearance above a roof shall extend a minimum of 24" (610mm) above the highest point when it passes through rhe roof
surface and any other obstruction within a horizontal distance of 18" (457mm).
* As specified in CAN/CGA B149 Installation Codes. Note: Local codes or regulations may require different clearances.
** A vent must not terminate directly above a sidewalk or paved driveway, which is located between two single-family dwellings
and serves both dwellings.
*** Only permitted if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor.
Always maintain minimum clearances around vent systems. The minimum clearances to
combustibles for horizontal vent pipe are 3" at the top and 1" at the sides and bottom of
the vent system until the pipe penetrates the nearest vertical wall. A 1 " minimum clearance
all around the pipe must be maintained. Do not pack the open air spaces with insulation
or other materials. This could cause high temperatures and may present a fire hazard.
15
VERTICAL THROUGH -THE -ROOF APPLICATIONS — RIGID VENTING ONLY
This Gas Fireplace has been approved for,
• Vertical installations up to 50' (15m) in height. Up to a 10' (3m) horizontal vent run can be installed within the vent system
using a maximum of two 90° elbows. See Figure 25.
40' Maximum Height
8' Minimum Height
Restrictor
Disk
�{- 10' –
I Maximum
Support St
Every 3'
1 i . .I Ii , 1
40' Maximum Height
8' Minimum Height
Restrictor
Disk
Figure 25- Support Straps for Horizontal Runs
• Up to two 450 elbows may be used within the
horizontal run. For each 45° elbow used on the
horizontal plane, the maximum horizontal length
must be reduced by 18" (450mm).
Example: Maximum horizontal length
No elbows 10' (3m)
1x45° elbows = 8.5' (2.6m)
2x45° elbows = 7' (2.1 m)
• A minimum of an 8' (2.5m) vertical rise is
required.
• Two sets of 450elbows offsets may be used within
the vertical sections. From 0 to a maximum of 8'
(2.5 m) of vent pipe can be used between elbows.
See Figure 26.
• 8 7 Series fireplaces allow for offsets. This
application will require that you first determine the
roof pitch and use the appropriate starter kit.
• The maximum angular variation allowed in the
system is 270°. See Figure 26
• The minimum height of the vent above the high-
est point of penetration through the roof is 2'
(610mm).
22
1 _
2
3 \
4
Restrictor= e®
Disk
Support
- 10' —tel_ Straps
Maximum Every
m=omw — 5'Vertical
I
Support S raps
Every 3'
o RESTRICTOR DISC
NOTE: The restrictor disc
included with the installation
instructions should be used
on vertically terminating
installations only.
Install the restrictor disc into
the flue collar of the appliance
with the bar horizontal.
Example: Elbow 1
= 90°
Elbow 2
= 45°
Elbow 3
= 45°
Elbow 4
= 90°
Total Angular Variation
= 270°
Figure 26'- Maximum Elbow Usage