Loading...
0201-158 (AR)LICENSED CONTRACTOR DECLARATION I hereby affirm -under penalty of perjury that I am licensed under provisions of Chapter 9 (commencing with Section 7000) of Division 3 of the Business and Professionals Code, and my License is in full force and effect. License # Lic. Class Exp. Date Date Signature of Contractor OWNER -BUILDER DECLARATION I hereby affirm under penalty of perjury that I am exempt from the Contractor's License Law for the following reason: ;( ) I, as owner of the property, or my employees with wages as their sole compensation, will do the work, and the structure is not intended or offered for sale (Sec. 7044, Business & Professionals Code). ( ) I, as owner of the property, am exclusively contracting with licensed contractors to construct the project (Sec. 7044, Business & Professionals Code). t () I am exempt under Section , B&P.C. for this, �.ea_son Date Signature of Owner l {, i-/ •' WORKER'S COMPENSATION DECLARATION I hereby affirm under penalty of perjury one of the following declarations: ( ) I have and will maintain a certificate of consent to self-insure,for workers' compensation, as provided for by Section 3700 of the Labor Code, for the performance of the work for which this permit is issued. ( ) I have and will maintain workers' compensation insurance, as required by Section 3700 of the Labor Code, for the performance of the work for which this permit is issued. My workers' compensation insurance carrier & policy no. are: Carrier Policy No. (This section need not be completed if the permit valuation is for $100.00 or less). I certify that in the performance of the work for which this permit is issued, I shall not employ any person in any manner so as to become subject to the workers' compensation laws of California, and agree that if I should become subject to the workers' compensation provisions of Section 3700 of the Labor Code, I shall forthwith comply with those provisions:, Date: Applicant Warning: Failure to secure Workers' Compensation coverage is unlawful and shall subject an employer to criminal penalties and civil fines up to $100,000, in addition to the cost of compensation, damages as provided for in Section 3706 of the Labor Code, interest and attorney's fees. IMPORTANT Application is hereby made to the Director of Building and Safety for a permit subject to the conditions and restrictions set forth on his, application. 1. Each person upon whose behalf this application is made & each person at whose request and for whose benefit work is performed under or pursuant to any permit issued as a result of this applicaton agrees to, & shall, indemnify & hold harmless the City of La Quinta, its officers, agents and employees. 2. Any permit issued as a result of this application becomes null and void if work is not commenced within 180 days from date of issuance of such permit, or cessation of work for 180 days will subject permit to cancellation. I certify that I have read this.application and state that the above information is correct. I agree to comply with all City, and State laws relating to the building construction, and hereby authorize representatives of this City to enter upon? _ the above-mentioned property for inspection purposes. Signature (Owner/Agent) ! `t ='.- •_ - ` t Date BUILDING PERMIT PERMIT# DATE / VALUATION LOT 0201-151 TRACT M48-1 JOB SITE APN ADDRESS Rfir. 1-9:&�'�A�AL C5��?.���r��` D� �� X xr9 r�P OWNER CONTRACTOR / DESIGNER / EN (NEER 55415 ROYAL fit OWMIR 1A Q111`14TA 92253 USE OF PERMIT CCiNV ?I:T i tlIX) 4i!'ti.{:.tt'.9N IP.ftY INTO 0;CK7A 1'0N R7C.N:W (3:311 S. R) C,°1JrsFt' M BONUS WOW CON-VE11 3rJ9.60 41 SKETWATED 00.9TOF C0,1'I.t9"Mt'JCrXM :$912.}0.go Y1rt ,, r ?Lm C;11FIC K FEE 101-000-439-31 R V591126 Ci]N,�'1'I?.iJ±w PIOi�I .i��ir 5:02 •�b�1CJ-�"r? �-a`aEifi $fit^+.OU Iv1W".'11MCA;f "It 101.000-421-000 $21.00 =C RICAL I+E9 101-000-420-000 $2J.0 STR01+10 MC' TION P.Ts - TWISID 101.000.241-000 •4 f D kt. T(,z' . �Li'd X011' AND 1;°LAV C':i:T">:CR I $11319 LFUN M13-PAWF'.C�RV $0,00 tb 21 2602 , .t Y ..� � � ; ► 31. .1 CITY �'QL1K"71 RECEIPT DATE ^BY ��t DA I AL I INS E OR j� INSPECTION RECORD OPERATION DATE INSPECTOR OPERATION DATE INSPECTOR BUILDING APPROVALS MECHANICAL APPROVALS Set Backs Underground Ducts Forms & Footings Ducts Slab Grade Return Air Steel Combustion Air Roof DeckExhaust Fans O.K. to Wrap / v F.A.U. Framing Compressor Insulation Vents Fireplace P.L. Grills Fireplace T.O. Fans & Controls Party Wall Insulation Condensate Lines Party Wall Firewall Exterior Lath / O Dryvrall - Int. Lath Final Final BLOCKWALL APPROVAL POOLS - SPAS steel Set Backs Electric Bond Footings Main Drain Bond Beam Approval to Cover Equipment Location Underground Electric Underground Plbg. Test Final Gas Piping PLUMBING APPROVALS Gas Test Electric Final Waste Lines Heater Final Water Piping Plumbing Final Plumbing Top Out Equipment Enclosure Shower Pans O.K. for Finish Plaster Sewer Lateral Pool Cover Sewer Connection Encapsulation Gas Piping Gas Test Appliances Final Final Utility Notice (Gas) ELECTRICAL APPROVALS Temp. Power Pole Underground Conduit Rough Wiring Low Voltage Wiring Fbdures Main Service Sub Panels Exterior Receptacles G.F.I. Smoke Detectors Temp. Use of Power Final Utility Notice (Perm) COMMENTS: It, WE —7 W, Bin I City of La Quints Building 8r Safety Division ' . P.O: Box 1504, 78-495 Calle Tampico La Quinta, CA 92253 - (760) 777-7012 Building Permit Application and Tracking Sheet Permit # 62 61 I -G>18 Project Address: e�eoL!x—(�::-,40wner's Name: (--0 A. P. Number: '76'7 - 5? -0 008 V Address: -Si 41 Legal Description:_ gjT2A!;X City, ST, Zip: Contractor:is Telephone: . .. ............................. . ........................... . .. ........ ... ........ -X, ... . . . . . . . . . . . . . Address: Project Description: ity, ST, Zip: City, Te Telephone: XXXXX ........... t. State Lic. # Arch., Engr., Designer: [Address: City Lic. "J City, ST, Zip: Telephone: State Lic. #: Name of Contact Person: ........... .. ................. ........ ...... . X .......... . ..... ......... ..................... X .......... nstruction Type: OccupancN. Pr oject type (circle one): New Add'n Alter Repair Demo Sq. Ft.: ZA�Sbz3q # Stories: -T Units. Telephone 4 of Contact Person: inEstimated Value of Project: X 30 6/07 APPLICANT: DO NOT WRITE BELOW THIS LINE N Submittal R e q'd Rec'd TRACKING PERMIT FEES 2 Plan Sets I— Plan Check submitted 141-110, Item Amount Structural CaIcs. Reviewed, read., for corrections 40'/2.VFY Plan Check Deposit Truss CaIcs. Called Contact Person I Plan Check Balance 7_ Title 24 CaIcs. Plans picked up tS Construction Flood plain plan Plans resubmittedA ollo7l0j. Mechanical Grading plan 2,d Review, ready for corrections issue Z t9 Electrical Subcontactor List Called Contact Person Z�AVOZ, Plumbing Grant Deed Plans picked up S.M.I. H.O.A. Approval Plans resubmitted Grading IN HOUSE:- Review, ready for corrections/issue Developer Impact Fee Planning Approval Called Contact Person A.I.P.P, Pub. Wks. Appr Date of permit issue School Fees Total Permit Fees Sc2; pT ,vE T�t Ivi (Al Gj NAN 1° r1116 DooR vg TyPf )( �ET-�CTor�- e♦ r %Xi- 67F i -- Eclachella Valley Ui*d School District P.O. Box 847, Thermal, CA 92274 (760) 398-5909 — Fax (760) 398-1224 • This Box For District Use Only DEVELOPER FEES PAID AREA: AMOUNT: RCPT #: CK #: CASH: IMT1A -S: DATE: CERTIFICATE OF COMPLIANCE (California Education Code 17620) Project Name: Date: January 28, 2002 Owner's Name: Rita M. Pacheco Phone No. 564-9557 Project Address: 55415 Royal St pGi- orgg, La Ouinta, CA 92253 Project Description: r_nnvPrt garagEhay into rP _ room APN: 767-520-008 Tract #: Type of Development: Residential XXXXX Commercial Lot #'s: Total Square Feet of Building Area: 330 sq. ft. Industrial Certification of Applicant/Owners: The person signing certifies that the above information is correct and makes this statement under penalty of rjury and further represents that he/she is authorized to ign on behalf of the owner/developer. Dated: Signature: SCHOOL DISTRICT'S REQUIREMENTS FOR THE ABOVE PROJECT HAVE BEEN OR WILL BE SATISFIED IN ACCORDANCE WITH ONE OF THE FOLLOWING: (CIRCLE ONE) Education Code Gov. Code Project 17620 65995 Approval Number of Sq.Ft. 330 Amount per Sq.Ft. $ Amount Collected $ -0- Building Permit Application Completed: Yes/No Agreement Existing Not Subject to Fee Prior to 1/1/87 Requirement Note: Pursuant to AB -181, any room addition or enclosures of 500 sq. ft. or lessare, exempt from developer fees. By: Foch "Tut" Pensis, Assistant Superintendent Administrative Services Administrator in Charge 44 C Certificate issued by: E1 vi ra Mattson Signature: Office Technician NOTICE OF 90 DAY PERIOD FOR PROTEST OF FEES AND STATEMENT OF FEES Section 66020 of the Government Code asserted by Assembly Bill 3081, effective January 1, 1997, requires that this District provide (1) a written notice to the project appellant, at the time of payment of school fees, mitigation payment or other exactions ("Fees"), of the 90 -day period to protest the imposition of these Fees and (2) the amount of the fees. Therefore, in accordance with section 66020 of the Government code and other applicable law, this Notice shall serve to advise you that the 90 -day protest period in regard to such Fees or the validity thereof, commences with the payment of the fees or performance of any other requirements as described in section 66020 of the Government code. Additionally, the amount of the fees imposed is as herein set forth, whether payable at this time or in whole or in part prior to issuance of a Certificate of Occupancy. As in the latter, the 90 days starts on the date hereof. This Certificate of Compliance is valid for thirty (30) days from the date of issuance. Extension will be granted only for good cause, as determined by the School District, and up to three (3) such extensions may be granted. At such time as this Certificate expires, if a building permit has not been issued for the project that is the subject of this Certificate, the owner will be reimbursed all fees that were paid to obtain this Certificate of Compliance. MV:c/mydocs/devfees/certificate of compliance 07/24/01 INSTALLATION CERTIFICATE CF -6R Site Address Permit Number DUCT LEAKAGE AND DESIGN DIAGNOSTICS DUCT LEAKAGE REDUCTION Pressurization Test Results (CFM @ 25 PA) Test Leakage (CFM) 373 Fan Flow If Fan Flow is Calculated as 400 cfm/ton x number of tons, or as 21.7 x Heating Capacity in Thousands of Btu/hr, enter calculated value here If fan flow is measured, enter measured value here Leakage Fraction = Test Leakage/(Measured or Calculated Fan Flow) _ ,b Pass if leakage fraction 9-- ❑ le5I S�•yj 4-/ 1?141lbdv% o2s/a Pass Fail ❑ For AEROSOL TYPE SEALANTS ONLY - The following diagnostic testing was completed: Duct Fan Pressurization at rough -in measured leakage (CFM) CHECK AFTER FINISHING WALL: ❑ Yes ❑ No ❑ Pressure pan test or House pressurization test ❑ Yes ❑ No ❑ Visual Inspection of Duct Connections ❑ ❑ Pass Fail ❑ THERMOSTATIC EXPANSION VALVE (TXV) ❑ Yes ❑ No Thermostatic Expansion Valve (or Commission approved equivalent) is installed and Access is provided for inspection ❑ ❑ Yes is a pass Pass Fail / - ❑ DUCT DESIGN 1 • ❑ Yes ❑ No ACCA Manual D Design calculations have been completed, Duct Design is on the plans and duct installation matches plans. 41-14 2• ❑ Yes ❑ No TXV is installed or Fan flow has been verified. If no TXV, verified fan flow matches design from CF -1R. Measured Fan Flow = ❑ ❑ Yes for both 1 and 2 is a Pass Pass Fail ❑ I, the undersigned, verify that the above diagnostic test results and the work I performed associated with the test(s) is in conformance with the requirements for compliance credit. [The builder shall provide the HERS provider a copy of the CF -6R signed by the builder employees or sub -contractors certifying that diagnostic testing and installation meet the requirements for compliance credit.] TestsSignature, Date Installing Subcontractor (Co. Name) OR Performed General Contractor (Co. Name) COPY TO: Building Department HERS Provider (if applicable) Building Owner at Occupancy U CITY OF LA QUINT fy CONTRACTOR U �` L JOB ADDRESS 5") 7 01Y A-( MIT NUMBER QZ-0 OWNER__ Rr'r)r '• XT:fif 6'0 BUILDER ✓�✓� This form shall be posted on the job with the Building InspieAlion Card at all t mea Ina cone cuoueIp aca. Only persons appearing on this list or their employees are authorized to work on this job. Any changes to thls list must be approved by the Building Division prior to commencement of work. Failure to comply will result in a stoppage of work and/or the voidance of building permit. For each applicable trade, all information requested below must be completed by applicant. "On File" is not an accentable res onse. ` Trade 1 Cleasitication - - Contre�tor . ' •-: :t::.. ' :• . tple.CorrIIactefa Ciceiiae>' .:......,.......- .... ...... . k r t;Mty 4Qmhxurad4a'•.:.:.�°.;•::",.:.';.:'<". -.�:.,C :Bu s;t:lcerjse Company Name Classification Ucenaa Number Exp. Date (e g- A. 8, C -BI lxxxxxx) (xxlxxlxx) Carrier Name le.g. State Fund. CalCompl Policy Number (Format Varies) Exp. Date pxlxxhuc) Ucensa Number Exp. Date fxxxx) (xxfxxlxx) EARTHWORK (C-12) - FRAMING Smet.:STE {C -Ft}- >— MasoNaY (1:•281 ' esM ell,e`S 3 G-2 o Fu 68 - 0 / PLUNIa(NQ 1C-36) ' 1,41r}I..0LASTER ica q DRYWALL IC -91 . fi44C is-ati>.60 u h4o 0 a� Ei.'TRIGAL:jC-1Q) '791/1/'7 8MBET IVIE7AL' _IC�431''' i I 8t:f1Y`IiO�•: t31¢P: jG-4��' .::, e 1!NTlPtti .C�AAIWIC "i(k�:IG-54T":_ i FC[d�tNG' �3i��• - aa4gS5�4Rnt olL i l% CN 1 i �4�� +� ►Jai aQ Pi�J fay-,�rf�uGpas�� . Z • 4141%u, NV q poc-10mle- Th ler, eq&NM-D kw 0gTctA 16Cit• �• �- 3$ tNSv�Oc�te►1 to R�i c c.+c Act���, tf DoE d • '� �N S ►�� 0 . icD u • FA c1oR- e• 6 1ZaltR. fog-: I. 'Duc -w Tl a U �CaEN� O=Sw' . 1< Nl� 30�) 3<x W -s' OLS VSO (DO 3s'x 6¢�' •� Q-% I u • 0"Eg : ?qA w 'Iac "E c c • CbIN4C2.50a of 141 GA04E, CITY Gr LA(QUI "FA BUILDING & SAFETY DEEPT. A, F1 P R, 6V E D FOR CONSTRUCTION DA T E I, / 22/ 0'2- BY I efflc%,- 5� A RE -INSPECTION FEE OF' $30 WILL BE CHARGED IF THE APPROVED PLANS AND JOB CARD ARE NOT ON THE SITE FOR A SCHEDULED INSPECTION. NO EXCEPTIONS! "AN ADEOUATELY SIZED DEBRIS CONTAINER IS REOUIRED ON THE JOB SITE DURING ALL PHASES OF CONSTRUCTION AND MUST BE EMPTIED AS NECESSARY FAILURE TO DO SO r,!AY CAUSE THE CITY TO HAVE THE CONTAINER DUMPED AT THE EXPENSE OF THE OWNER/ CONTRACTOR" Card �.� � �►J a s 5_� _ Q 6Logc1k -To u4L tNG t-tCaK flygL E LA r N 1 i_ Com. Srl,��� ( dvvr- �Su:F-Ct-os�a(a) D eLar l�bfe J �Su 7�U��9 Wti<<s IA.)5Ct r4•'('L. Ile,1 2 - C NV_ GAP-A61S (E) I 21 2 i PK0 N -i" OWNER / BUILDER INFORMATION Dear Property Owner: An application for a building permit has been submitted in your name listing yourself as the builder of the property improvements specified. For your protection you should be aware that as "Owner/ Builder" you are the responsible party of record on such a permit. Building permits are not required to be signed by property owners unless they are personally performing their own work. If your work is being performed by someone other than yourself, you may protect yourself from possible liability if that person applies for the proper permit in his or her name. Contractors are required by law to be licensed and bonded by the State of California and to have a business license from the City or County. They are also required by law to put their license number on all permits for which they apply. If you plan to do your own work, with the exception of various trades that you plan to subcontract, you should be aware of the following information for your benefit and protection: If you employ or otherwise engage any persons other than your immediate family, and the work (including materials and other costs) is $200.00 or more for the entire project, and such persons are not licensed as contractors or subcontractors, then you may be an employer. If you are an employer, you must register with the State and Federal Government as an employer,and you are subject to several obligations including State and Federal income tax withholding, federal social security taxes, worker's compensation insurance, disability insurance costs and unemployment compensation contributions. There may be financial risks for you if you do not carry out these obligations, and these risks are especially serious with respect to worker's compensation insurance. For more specific information about your obligations under Federal Law, contact the Internal Revenue Service (and, if you wish, the U.S. Small Business Adminstration). For more specific information about your obligations under State Law, contact the Department of Benefit Payments and the Division of Industrial Accidents. If the structure is intended for sale, property owners who are not licensed contractors are allowed to perform their work personally or through their own employees, without a licensed contractor or subcontractor, only under limited conditions. A frequent practice of unlicensed persons professing to be contractors is to secure an "Owner/ Builder" building permit, erroneously implying that the property owner is providing his or her own labor and material personally. Building permits are not required to be signed by property owners unless they are performing their own work personally. Information about licensed contractors may be obtained by contacting the Contractors' State License Board in your community or at 1020 N. Street, Sacramento, California 95814. Please complete and return the enclosed owner -builder verification form so that we can confirm that you arc aware of these matters. The building permit will not be issued until the verification is returned. Very truly yours, CITY OF LA QUINTA DEPT. OF BUILDING AND SAFETY 78-495 Calle Tampico La Quinta, CA 92253 (760)777-7012 FAX: (760) 777-7011 f= �. t9, � OWNER'S SIGNATURE/ DATE ss- vis q a. a s PROPERTY ADDRE Ot2,01 - ►t PERMIT NUMBER(s) 4 PSA FAIRWAYS ASSOCIATION December 26, 2001 Mrs. Rita M. Pacheco 55-415 Royal St. George La Quinta CA 92253 Re: 55-415 Royal St. George Dear Mrs. Pacheco, At the December 17, 2001 meeting of the ArchitectUral/Landscape Committee, your replacement of the garage door has been approved upon the following conditions: A. You must be in compliance with all city codes and ordinances. B. You must also comply with the CC&R's that allow owners to leave a vehicle in the driveway for no longer than 72 hours or it will be in violation. If you have any questions, you may contact me at 760-564-3858. Sincerely, Donna M accio Association- Manager P.O. BOX 13710 - PALM DESERT, CALIFORNIA 92255 - Tel. (760) 776-5100 - Fax (760) 776-5111 email: pgawest@monarchgrp.com TITLE 2 4 Energy Conservation Standards Compliance Report PACHECO RESIDENCE ADDITION ,55-415 ROYAL ST. GEORGE. - LQ January 4, 2002 • Job Number: 20375A Prepared For.- RITA PACHECO 55-415 ROYAL ST. GEORGE LA QUINTA, CA 92253 760-564-9557 CIN OF LA Q U I N TA BUILDING & SAFETY DEPT. APPROVED FOR CONSTRUCTAON DATE 22 D BY _ adlin's enterprises ♦®v®®®. Catherine M. Madlin, Certified Energy Analyst Post Office Box 1443 v Palm Springs, CA 92263 760-322-5004 / 323-3644 (fax) E-mail: CMadlin@aol.com Madlin-'s enterprises Catherine M. Madlin, Certified Energy Analyst v 760-322-5004 / 323-3644 (fax) V V ®O ®® Title 24 Energy Conservation Standards Compliance Report This proposed project has been reviewed for compliance with the 2001 State of California Energy Conservation Standards, Title 24, by Madlin's Enterprises. The building design described in this compliance portfolio is in conformance with the standards as outlined in the attached compliance forms and documentation. Date: January 4, 2002 Job Number: 20375A Prepared For: RITA PACHECO Project Name: PACHECO RESIDENCE ADDITION Project Location: 55-415 ROYAL ST. GEORGE - LQ Method of Compliance: MICROPAS V6.1 CERTIFIED COMPUTER PROGRAM Orientation Of Entry: EAST Certified Energy Analyst Catherine M. Madlin NR 98-90-544 r r /I R 98-90-144 C A D E C California Associadon of Building Energy Consultants • Post Office Box 1443 v Palm Springs, Ca 92263 v Madlin-'s enterprises Catherine M. Madlin, Certified Energy Analyst v 760-322-5004 / 323-3644 (fax) ®®®. ®® ;. S rQN ©F �IJ�,DTN �+ PONEI�TT NLLN GQMFETANGE EQCIiREMENTS job Name PACHECO RESIDENCE ADDITION job No. / File No. 20375A Method of Compliance Micropas V6.1 Computer Simulation Total Conditioned Square Footage 330 Sq.Ft. (Per Owner's Drawings) Total Glazing % (Floor/Glass Area Ratio) 9.4% Insulation: Roof / Ceiling R-38 Insulation: Walls R-19 Insulation: Floor - Slab on Grade None Required Insulation: H.V.A.C. Ducts/Location/Testing R-4.2 / Attic / Duct Testing Required: Extg + Add System only: 25% Adjusted Loss Rate Glazing U Value / Type: Operable & Fixed 0.60, Dual Pane, Wood Frame (CEC Default Value) Glazing: Solar Heat Gain Coefficient (Uncoated) 0.65 Operable & Fixed Glazing: Exterior Shading Overhangs As Shown Thermal Mass Square Footage & % Not Required H.V.A.C. System Type Existing System(s) Domestic Hot Water Heater Existing System(s) Other Requirements None v Post Office Box 1443 v Palm Springs, Ca 92263 v Madli y s en terpfises Catlzenne M. Madlin, Certified Enemy Analyst v 760-322-5004 / 323-3644 (fax) v v v v v v . Title 24 Compliance Forms CERTIFICATE OF COMPLIANCE: RESIDENTIAL Page 1 CF -1R Project Title.......... PACHECO.ADD Date..01/04/02 09:03:01 Project Address 55-415 ROYAL ST G 0 ******* J •••••••• E RGE INDIAN WELLS *v6.01* Documentation Author... CATHERINE M. MADLIN ******* Building Permit Madlin's Enterprises P.O. Box 1443 Plan Check Date Palm Springs, CA 92262 760-322-5004 Field Check/ Date Climate Zone.. ..... 15 Compliance Method...... MICROPAS6 v6.01 for 2001 Standards by Enercomp, Inc. MICROPAS6 v6.01 File -20375A6 Wth-CTZ15S92 Program -FORM CF -1R User#-MP0207 User-Madlin's Enterprises Run -NO DUCT TESTING GENERAL INFORMATION Conditioned Floor Area..... 330 sf Building Type .............. Single Family Detached Construction Type ......... Addition Alone Building Front Orientation. Front Facing 90 deg (E) Number of Dwelling Units... 1 Number of Stories.. ....... 1 Floor Construction Type.... Slab On Grade Glazing Percentage......... 9.4 % of floor area • Average Glazing U -factor... 0.6 Btu/hr-sf-F Average Glazing SHGC....... 0.65 Average Ceiling Height..... 10 ft BUILDING SHELL INSULATION Component Frame Cavity Sheathing Total Assembly Type Type R -value R -value R -value U -factor Location/Comments Wall Wood R-17.8 R-0 R-17.8 0.065 Door None R-0 R-0 R-0 0.330 Roof Wood R-11 R-27 R-38 0.025 SlabEdge None R-0 R-0 F2=0.760 SlabEdge None R-0 R-0 F2=0.510 FENESTRATION Over - Area. U- Interior Exterior hang/ Orientation (sf) Factor SHGC Shading Shading Fins Window Front (E) 15.5 0.600 0.650 Standard Standard Yes Window Front (E) 15.5 0.600 0.650 Standard Standard Yes SLAB SURFACES Area Slab Type (sf) Standard Slab 330 CERTIFICATE OF COMPLIANCE: RESIDENTIAL Page 2 CF -1R Project Title.......... PACHECO.ADD Date..01/04/02 09:03:01 MICROPAS6 v6.01 File -20375A6 Wth-CTZ15S92 Program -FORM CF -1R User#-MP0207 User-Madlin's Enterprises Run -NO DUCT TESTING HVAC SYSTEMS DUCT TESTING DETAILS Duct Measured Supply Leakage Target Duct Surface Area Equipment Type (% fan CFM/CFM25) (ft2) Furnace./ ACSplitTXV 6% / 13.9 n/a SPECIAL FEATURES AND MODELING ASSUMPTIONS -i ***.Items in this section should be documented on the plans, *** *** installed to manufacturer and CEC specifications, and *** *** verified during plan check and field inspection. *** This building incorporates Tested Duct Leakage. This building incorporates either Tested Refrigerant Charge and Airflow (RCA) or a Thermostatic Expansion Valve (TXV) on the specified air conditioning system(s). HERS REQUIRED VERIFICATION ***.Items in this section require field testing and/or *** *** verification by a certified home energy rater under *** *** the supervision of a CEC-approved HERS provider using *** *** CEC approved testing and/or verification methods.and *** *** must be reported on the CF -6R installation certificate. *** This building incorporates Tested Duct Leakage. Target CFM leakage values measured at 25 pascals are shown in DUCT TESTING DETAILS above or may be calculated as documented on the CF -6R. If the measured CFM is above the target, then corrective action must be taken to reduce the duct leakage and then must be retested. Alternatively, the compliance calculations could be redone without duct testing. If ducts are not installed, then HERS verification is not necessary for Tested Duct Leakage. This building incorporates either Tested Refrigerant Charge and Airflow (RCA) or a Thermostatic Expansion Valve (TXV) on the specified air conditioning system(s). If a cooling system is not installed, then HERS verification is not necessary for the RCA or TXV. Refrigerant Tested ACCA Equipment Minimum Charge and • Duct Duct Duct Manual Thermostat Type Efficiency Airflow Location R -value Leakage D Type Furnace 0.780 AFUE n/a Attic R-4.2 Yes No Setback ACSplitTXV 10.00 SEER Yes Attic R-4.2 Yes No Setback DUCT TESTING DETAILS Duct Measured Supply Leakage Target Duct Surface Area Equipment Type (% fan CFM/CFM25) (ft2) Furnace./ ACSplitTXV 6% / 13.9 n/a SPECIAL FEATURES AND MODELING ASSUMPTIONS -i ***.Items in this section should be documented on the plans, *** *** installed to manufacturer and CEC specifications, and *** *** verified during plan check and field inspection. *** This building incorporates Tested Duct Leakage. This building incorporates either Tested Refrigerant Charge and Airflow (RCA) or a Thermostatic Expansion Valve (TXV) on the specified air conditioning system(s). HERS REQUIRED VERIFICATION ***.Items in this section require field testing and/or *** *** verification by a certified home energy rater under *** *** the supervision of a CEC-approved HERS provider using *** *** CEC approved testing and/or verification methods.and *** *** must be reported on the CF -6R installation certificate. *** This building incorporates Tested Duct Leakage. Target CFM leakage values measured at 25 pascals are shown in DUCT TESTING DETAILS above or may be calculated as documented on the CF -6R. If the measured CFM is above the target, then corrective action must be taken to reduce the duct leakage and then must be retested. Alternatively, the compliance calculations could be redone without duct testing. If ducts are not installed, then HERS verification is not necessary for Tested Duct Leakage. This building incorporates either Tested Refrigerant Charge and Airflow (RCA) or a Thermostatic Expansion Valve (TXV) on the specified air conditioning system(s). If a cooling system is not installed, then HERS verification is not necessary for the RCA or TXV. CERTIFICATE OF COMPLIANCE: RESIDENTIAL Page 3 CF -1R Project Title.......... PACHECO.ADD Date..01/04/02 09:03:01 MICROPAS6 v6.01 File -20375A6 Wth-CTZ15S92 Program -FORM CF -1R User#-MP0207 User-Madlin's Enterprises Run -NO DUCT TESTING REMARKS The values and materials used in this compliance portfolio are the minimum required to show compliance with Title 24 Energy Conservation Standards. The owner may (at his/her option) install better materials without additional compliance calculations. The installing glazing contractor shall provide the required CF -6R Installation Certificate with the installed glazing values and areas. The duct system serving the addition shall be tested by a HERS Certified Rater. The existing -plus -addition duct system shall meet a target leakage rate of 25% as outlined in the 2001 CEC Residential Design Manual, Chapter 7, Page 7-13. The HVAC system is existing. The domestic hot water heaters are existing. CERTIFICATE OF COMPLIANCE: RESIDENTIAL Page 4 CF -1R Project Title.......... PACHECO.ADD Date..01/04/02 09:03:01 MICROPAS6 v6.01 File -20375A6 Wth-CTZ15S92 Program -FORM CF -1R User#-MP0207 User-Madlin's Enterprises Run -NO DUCT.TESTING COMPLIANCE STATEMENT This certificate of compliance lists the building features and performance specifications needed to comply with Title -24, Parts 1 and 6 of the California Code of Regulations, and the administrative regulations to implement them. This certificate has been signed by the individual with overall design responsibility. When this certificate of compliance is submitted for a single building plan to be built in multiple orientations, any shading feature that is varied is indicated in the Special Features Modeling Assumptions section. DESIGNER or OWNER Name.... RITA PACHECO Company. Owner Address. 55-415 ROYAL ST. GEORGE LA QUINTA, CA Phone... 760-564-9557 License. Signed.. (date)] ENFORCEMENT AGENCY Name.... Title... Agency.. Phone... Signed.. (date) DOCUMENTATION AUTHOR Name.... CATHERINE M. MADLIN Company. Madlin's Enterprises Address. P.O. Box 1443 Palm Springs, CA 92262 Phone... 760-322-5004 Signed.. A&w"0010��� (date) Certified Energy Analyst Catherine M. Medlin NR 98-90-544 r r R 98-90-144 rr CAdEC California Association of Building Energy Consultants MANDATORY MEASURES CHECKLIST: RESIDENTIAL (page 1 of 2) MF -1R Note: Lowrise residential buildings subject to the Standards must contain these measures regardless of the compliance approach used. Items marked with an asterisk (*) may be superseded by more stringent compliance requirements listed on the Certificate of Compliance. When this checklist is incorporated into the permit documents, the features noted shall be considered by all parties as minimum component performance specifications for the mandatory measures whether they are shown elsewhere in the documents or on this checklist only. Instructions: Check or initial applicable boxes when completed or enter N/A if not applicable. DESCRIPTION DESIGNER ENFORCEMENT Building Envelope Measures: * §150(a): Minimum R-19 ceiling insulation. § 150(b): Loose fill insulation manufacturer's labeled R -Value. * § 150(c): Minimum R-13 wall insulation in wood framed walls or equivalent U -Factor in metal frame walls (does not apply to exterior mass walls). * §I50(d): Minimum R-13 raised floor insulation in framed floors. §150(1): Slab edge insulation -water absorption rate no greater than 0.3%, water vapor transmission rate no greater than 2.0perm/inch. §118: Insulation specified or installed meets insulation quality standards. Indicate type and form. § 116-17: Fenestration Products, Exterior Doors, and Infiltration/Exfiltration Controls 1. Doors and windows between conditioned and unconditioned spaces designed to limit air leakage. 2. Fenestration products'(except field -fabricated) have label with certified U -Factor, certified Solar Heat Gain Coefficient (SHGC), and infiltration certification. 3. Exterior doors and windows weatherstripped; all joints and penetrations caulked and sealed. § 150(g): Vapor barriers mandatory in Climate Zones 14 and 16 only. §I50(f): Special infiltration barrier installed to comply with § 151 meets Commission quality standards. § 150(e): Installation of Fireplaces, Decorative Gas Appliances and Gas Logs. 1. Masonry and factory -built fireplaces have: a. Closeable metal or glass door b. Outside air intake with damper and control c. Flue damper and control 2. No continuous burning gas pilot lights allowed. Spare Conditioning, Water Heating and Plumbing System Measures: § 110-§ 113: HVAC equipment, water heaters, showerheads and faucets certified by the Commission. . § 150(h): Heating and/or cooling loads calculated in accordance with ASHRAE, SMACNA or ACCA. § I50(i): Setback thermostat on all applicable heating and/or cooling systems. § I500): Pipe and tank insulation 1. Storage gas water heaters rated with an Energy Factor less than 0.58 must be externally wrapped with insulation having an installed thermal resistance of R-12 or greater. 2. First 5 feet of pipes closest to water heater tank, non -recirculating systems, insulated (R-4 or greater) 3. Back-up tanks for solar system, unfired storage tanks, or other indirect hot water tanks have R-12 external insulation or R-16 combined intemal/extemal insulation. 4. All buried or exposed piping insulated in recirculating sections of hot water systems. 5. Cooling system piping below 55° F insulated. 6. Piping insulated between heating source and indirect hot water tank. January 4, 2001 MANDATORY MEASURES CHECKLIST: RESIDENTIAL (Page 2 of 2) MF -1R Note: Lowrise residential buildings subject to the Standards must contain these measures regardless of the compliance approach used. Items marked with an asterisk (*) may be superseded by more stringent compliance requirements listed on the Certificate of Compliance. When this checklist is incorporated into the permit documents, the features noted shall be considered by all parties as minimum component performance specifications for the mandatory measures whether they are shown elsewhere in the documents or on this checklist only. Instructions: Check or initial applicable boxes when completed or enter N/A if not applicable. DESCRIPTION DESIGNER ENFORCEMENT Space Conditioning, Water Heating and Plumbing System Measures: (continued) * § 150(m): Ducts and Fans 1. All ducts and plenums installed, sealed and insulated to meet the requirement of the 1998 CMC Sections 601, 603, 604, and Standard 6-3; ducts insulated to a minimum installed level of R-4.2 or enclosed entirely in conditioned space. Openings shall be sealed with mastic, tape, aerosol sealant, or other duct -closure system that meets the applicable requirements of UL 181, UL 181A, or UL 181B. If mastic or tape is used to seal openings greater than 1/4 inch, the combination of mastic and either mesh or tape shall be used. Building cavities shall not be used for conveying conditioned air. Joints and seams of duct systems and their components shall not be sealed with cloth back rubber adhesive duct tapes unless such tape is used in combination with mastic and drawbands. 2. Exhaust fan systems have back draft or automatic dampers. 3. Gravity ventilating systems serving conditioned space have either automatic or readily accessible, manually operated dampers. § 114: Pool and Spa Heating Systems and Equipment. 1. System is certified with 78% thermal efficiency, on-off switch, weatherproof operating instructions, no electric resistance heating and no pilot light. 2. System is installed with: a At least 36" of pipe between filter and heater for future solar heating. b. Cover for outdoor pools or outdoor spas. 3. Pool system has directional inlets and a circulation pump time switch. §1 15: Gas fired central furnaces, pool heaters, spa heaters or household cooking appliances have no -continuously burning pilot light. (Exception: Non -electrical cooking appliances with pilot < 150 Btu/hr) Lighting Measures: § 150(k)1.: Luminaires for general lighting in kitchens shall have lamps with an efficacy of 40 lumens/watt. or greater for general lighting in kitchens. This general lighting shall be controlled by a switch on a readily accessible lighting control panel at an entrance to the kitchen. § I50(k)2.: Rooms with a shower or bathtub must have either at least one luminaire with lamps with an efficacy of 40 lumens/watt or greater switched at the entrance to the room or one of the alternatives to this requirement allowed in § 150(k)2.; and recessed ceiling fixtures are IC insulation cover approved. January 4, 2001 COMPUTER METHOD SUMMARY Page 1 C -2R Project Title.......... PACHECO.ADD Date..01/04/02 09:03:01 Project Address 55-415 ROYAL ST G ******* •••••••• EORGE INDIAN WELLS *v6.01* Documentation Author... CATHERINE M. MADLIN ******* Building Permit Madlin's Enterprises P.O. Box 1443 Plan Check Date Palm Springs, CA 92262 760-322-5004 Field Check/ Date Climate Zone.. ..... 15 Compliance Method...... MICROPAS6 v6.01 for 2001 Standards by Enercomp, Inc. MICROPAS6 v6.01 File -20375A6 Wth-CTZ15S92 Program -FORM C -2R User#-MP0207 User-Madlin's Enterprises Run -NO DUCT TESTING GENERAL INFORMATION Conditioned Floor Area..... 330 sf Building Type .............. Single Family Detached Construction Type ......... Addition Alone Building Front Orientation. Front Facing 90 deg (E) Number of Dwelling Units... 1 Number of Building Stories. 1 Weather Data Type.......... FullYear Floor Construction Type.... Number of Building Zones... Conditioned Volume......... Slab -On -Grade Area......... Glazing Percentage......... Average Glazing U -factor... Average Glazing SHGC....... Average Ceiling Height..... Floor Area Volume Zone Type (sf) (cf) Slab On Grade 1 3300 cf 330 sf 9.4 % of floor area 0.6 Btu/hr-sf-F 0.65 10 ft BUILDING ZONE INFORMATION # of Dwell Cond- Thermostat Units itioned Type Vent MICROPAS6 ENERGY USE SUMMARY Height Energy Use Standard Proposed Compliance (kBtu/sf-yr) Design Design Margin Space Heating.......... 3.67 2.43 1.24 Space Cooling.......... 70.07 64.95 5.12 Total 73.74 67.38 6.36 *** Water Heating not calculated *** GENERAL INFORMATION Conditioned Floor Area..... 330 sf Building Type .............. Single Family Detached Construction Type ......... Addition Alone Building Front Orientation. Front Facing 90 deg (E) Number of Dwelling Units... 1 Number of Building Stories. 1 Weather Data Type.......... FullYear Floor Construction Type.... Number of Building Zones... Conditioned Volume......... Slab -On -Grade Area......... Glazing Percentage......... Average Glazing U -factor... Average Glazing SHGC....... Average Ceiling Height..... Floor Area Volume Zone Type (sf) (cf) Slab On Grade 1 3300 cf 330 sf 9.4 % of floor area 0.6 Btu/hr-sf-F 0.65 10 ft BUILDING ZONE INFORMATION # of Dwell Cond- Thermostat Units itioned Type Vent Vent Air Height Area Leakage (ft) (sf) Credit 1. ZONE Residence 330 3300 1.00 Yes Setback 2.0 Standard No COMPUTER METHOD SUMMARY Page 2 C -2R Prnipnt Tit1P_ _ Daruron Ann . _. - A /nw /nn nn nn ... MICROPAS6 v6.01 File -20375A6 Wth-CTZ15S92 Program -FORM C -2R User#-MP0207 User-Madlin's Enterprises Run -NO DUCT TESTING Surface Length F2 Insul Solar (ft) Factor R-val Gains Location/Comments 1.ZONE - New 7 SlabEdge 46 8 SlabEdge 23 Orientation 1.ZONE - New 1 Window' Front (E) 2 Window Front (E) 0.760 R-0 No 0.510 R-0 No FENESTRATION SURFACES Area U- Act Exterior Shade Interior Shade (sf) factor SHGC Azm Tilt Type/SHGC Type/SHGC 15.5 0.600 0.650 9.0 90 Standard/0.76 Standard/0.68 15.5 0.600 0.650 90 90 Standard/0.76 Standard/0.68 OVERHANGS AND SIDE FINS Window— ---Overhang Left Fin OPAQUE SURFACES Area Left Area U- Insul Act Asf) Solar Form 3 Location/ Surface (sf) factor R-val Azm Tilt Gains Reference Comments 1.ZONE - New 15.5 3 5.25 8 1 n/a n/a n/a n/a n/a n/a n/a n/a 2 Window 15.5 1 Wall 119 0.065 17.8 90 90 Yes W.19.2X6.16 2 Wall 285 0.065 17.8 180 90 Yes W.19.2X6.16 3 Wall 20 0.065 17.8 270 90 Yes W.19.2X6.16 4 Wall 209 0.065 17.8 90 90 No W.19.2X6.16 5 Door 24 0.330 0 90 90 No None 6 Roof 330 0.025 38 n/a 0 Yes R.38.2X4.24 PERIMETER LOSSES Surface Length F2 Insul Solar (ft) Factor R-val Gains Location/Comments 1.ZONE - New 7 SlabEdge 46 8 SlabEdge 23 Orientation 1.ZONE - New 1 Window' Front (E) 2 Window Front (E) 0.760 R-0 No 0.510 R-0 No FENESTRATION SURFACES Area U- Act Exterior Shade Interior Shade (sf) factor SHGC Azm Tilt Type/SHGC Type/SHGC 15.5 0.600 0.650 9.0 90 Standard/0.76 Standard/0.68 15.5 0.600 0.650 90 90 Standard/0.76 Standard/0.68 OVERHANGS AND SIDE FINS Window— ---Overhang Left Fin Right Fin— Area Left Rght Surface Asf) Wdth Hgth Dpth Hght Ext Ext Ext Dpth Hght Ext Dpth Hght 1.ZONE - New 1 Window 15.5 3 5.25 8 1 n/a n/a n/a n/a n/a n/a n/a n/a 2 Window 15.5 3 5.25 8 1 n/a n/a n/a n/a n/a n/a n/a n/a SLAB SURFACES Area Slab Type (sf) 1.ZONE Standard Slab 330 COMPUTER METHOD SUMMARY Page 3 C -2R Project Title.......... PACHECO.ADD Date..01/04/02 09:03:01 MICROPAS6 v6.01 File -20375A6 Wth-CTZ15S92 Program -FORM C -2R User#-MP0207 User-Madlin's Enterprises Run -NO DUCT TESTING HVAC SYSTEMS Refrigerant Tested ACCA System Minimum Charge and Duct Duct Duct Manual Duct Type Efficiency Airflow Location R -value Leakage D Eff 1.ZONE Furnace 0.780 AFUE n/a Attic R-4.2 Yes No 0.815 ACSplitTXV 10.00 SEER Yes Attic R-4.2 Yes No 0.703 DUCT TESTING DETAILS Duct Measured Supply Leakage Target Duct Surface Area Equipment Type (% fan CFM/CFM25) (ft2) 1.ZONE Furnace / ACSplitTXV 6% / 13.9 n/a SPECIAL FEATURES AND MODELING ASSUMPTIONS *** Items in this section should be documented on the plans, *** . *** installed to manufacturer and CEC specifications, and *** *** verified.during plan check and field inspection. *** This building incorporates Tested Duct Leakage. This building incorporates either Tested Refrigerant Charge and Airflow (RCA) or a Thermostatic Expansion Valve (TXV) on the specified air conditioning system(s). HERS REQUIRED VERIFICATION *** Items in this section require field testing and/or *** *** verification by a certified home energy rater under *** *** the supervision of a CEC-approved HERS provider using *** *** CEC approved testing and/or verification methods.and *** *** must be reported on the CF -6R installation certificate. *** This building incorporates Tested Duct Leakage. Target CFM leakage values measured at 25 pascals are shown in DUCT TESTING DETAILS above or may be calculated as documented on the CF -6R. If the measured CFM is above the target, then corrective action must be taken to reduce the duct leakage and then must be retested. Alternatively, the compliance calculations could be redone without duct testing. If ducts are not installed, then HERS verification is not necessary for Tested Duct Leakage. This building incorporates either Tested Refrigerant Charge and Airflow (RCA) or a Thermostatic Expansion Valve (TXV) on the specified air conditioning system(s). If a cooling system is not installed, then HERS verification is not necessary for the RCA or TXV. COMPUTER METHOD SUMMARY Page 4 C -2R Project Title.......... PACHECO.ADD Date. -01/04/02 09:03:01 MICROPAS6 v6.01 File -20375A6 Wth-CTZ15S92 Program -FORM C -2R User#-MP0207 User-Madlin's Enterprises Run -NO DUCT TESTING REMARKS The values and materials used in this compliance portfolio are the minimum required to show compliance with Title 24 Energy Conservation Standards. The owner may (at his/her option) install better materials without additional compliance calculations. The installing glazing contractor shall provide the required CF -6R Installation Certificate with the installed glazing values and areas. The duct system serving the addition shall be tested by a HERS Certified Rater. The existing -plus -addition duct system shall meet a target leakage rate of 25% as outlined in the 2001 CEC Residential Design Manual, Chapter 7, Page 7-13. The HVAC system is existing. The domestic hot water heaters are existing. Madlin-'s enterprises Catherine M. Madlij4 Certified Energy Analyst . 760-322-5004 / 323-3644 (fax) ®®®®® ® H. V.A. C. Load Calculation HVAC SIZING Page 1 HVAC Project Title.......... PACHECO.ADD Date..01/04/02 09:03:01 Project Address 55-415 ROYAL ST GEORGE ******* INDIAN WELLS *v6.01* Documentation Author... CATHERINE M. MADLIN ******* Building Permit Madlin's Enterprises P.O. Box 1443 Plan Check Date Palm Springs, CA 92262 760-322-5004 Field Check/ Date Climate Zone.. ..... 15 Compliance Method...... MICROPAS6 v6.01 for 2001 Standards by Enercomp, Inc. MICROPAS6 v6.01 File -20375A6 Wth-CTZ15S92 Program -HVAC SIZING User#-MP0207 User-Madlin's Enterprises Run -NO DUCT TESTING GENERAL INFORMATION FloorArea ................. Volume.. .... ........... Front Orientation.......... Sizing Location............ Latitude... ............... Winter Outside Design...... Winter Inside Design....... Summer Outside Design...... Summer Inside Design....... Summer Range........ ..... Interior Shading Used...... Exterior Shading Used...... Overhang Shading Used...... Latent Load Fraction....... Description 330 sf 3300 cf Front Facing PALM DESERT 33.7 degrees 32 F 70 F 112 F 78 F 34 F No No No 0.20 HEATING AND COOLING LOAD SUMMARY Opaque Conduction and Solar...... Glazing Conduction: .............. Glazing Solar .................... Infiltration ..................... Internal Gain .................... Ducts. .. ................... Sensible Load .................... LatentLoad ...................... 90 deg (E) Heating Cooling (Btuh) (Btuh) 3959 1855 708 634 n/a 1758 1743 1153 n/a 1050 641 645 7051 7094 n/a 1419 Minimum Total Load 7051 8513 Note: The loads shown are only one of the criteria affecting the selection of HVAC equipment. Other relevant design factors such as air flow requirements, outside air, outdoor design temperatures, coil sizing, availability of equipment, oversizing safety margin, etc., must also be considered. It is the HVAC designer's responsibility to consider all factors when selecting the HVAC equipment. HVAC SIZING Page 2 HVAC Project Title.......... PACHECO.ADD Date..01/04/02 09:03:01 MICROPAS6 v6.01 File -20375A6 Wth-CTZ15S92 Program -HVAC SIZING User#-MP0207 User-Madlin's Enterprises Run -NO DUCT TESTING TOTAL HEATING LOAD: 7051 HEATING LOAD CALCULATIONS DESIGN CONDITIONS FOR ZONE '1.ZONE': WINTER DESIGN TEMPERATURES: InsideTemperature ................................ 70.0 F OutsideTemperature ............................... 32.0 F DESIGN TEMPERATURE DIFFERENCES Standard .......................................... 38.0 F CONDUCTIVE HEAT LOSS: U -factor Heat Area (Btu/hr- TD Loss Description Orientation. (sf) sf-F) (F) (Btuh) Wall East 119.0 x 0.0655 x 38.0 = 296 Wall South 285.0 x 0.0655 x 38.0 = 709 Wall West 20.0 x 0.0655 x 38.0 = 50 Shaded Wall n/a 209.0 x 0.0655 x 38.0 = 520 Shaded Wall n/a 24.0 x 0.3300 x 38.0 = 301 Roof Horizontal 330.0 x 0.0247 x 38.0 = 310 SlabEdge n/a 46.0 x 0.7600 x 38..0 = 1328 SlabEdge n/a 23.0 x 0.5100 x 38.0 = 446 CONDUCTIVE TOTALS FOR OPAQUE SURFACES 3959 Double Window East 15.5 x 0.6000 x 38.0 = 354 Double Window East 15.5 x 0.6000 x 38.0 = 354 CONDUCTIVE TOTALS FOR GLAZING SURFACES 708 INFILTRATION: (Type: Medium) 3300 cuft x 0.77 ac/hr x 0.018 Btu/cuft-F x 38.0 = 1743 SUBTOTAL 6410 DUCT HEAT LOSS: Duct Location: Attic 0.10 x 6410 = 641 TOTAL HEATING LOAD: 7051 HVAC SIZING Page 3 HVAC Project Title.......... PACHECO.ADD Date..01/04/02 09:03:01 MICROPAS6 v6.01 File -20375A6 Wth-CTZ15S92 Program -HVAC SIZING User#-MP0207 User-Madlin's Enterprises Run -NO DUCT TESTING COOLING LOAD CALCULATIONS DESIGN CONDITIONS FOR ZONE '1.ZONE': SUMMER DESIGN CONDITIONS: InsideTemperature ................................ Outside Temperature 78.0 F ....................... Temperature Range ................................. ......112.0 34.0 F F DESIGN EQUIVALENT TEMPERATURE DIFFERENCES Standard...... ................................... FrameWalls and Doors 34.0 32.6 F ............................. Ceiling Under Vented Attic ........................ 53.0 F F Frame Partitions .................................. 24.0 F CONDUCTIVE HEAT GAIN: U -factor Heat Area (Btu/hr- TDeq Gain Description Orientation (sf) sf-F) (F) (Btuh) Wall East 119.0 x 0.0655 x 32.6 = 254 Wall South 285.0 x 0•.0655 x 32.6 = 608 Wall West 20.0 x 0.0655 x 32.6 = 43 Shaded Wall n/a 209.0 x 0.0655 x 24.0 = 328 Shaded Wall n/a 24.0 x 0.3300 x 24.0 = 190 Roof Horizontal 330.0 x 0.0247 x 53.0 = 432 CONDUCTIVE TOTALS FOR OPAQUE SURFACES 1855 Double Window East 15.5 x 0.6000 x 34.0 = 317 Double Window East 15.5 x 0.6000 x 34.0 = 317 CONDUCTIVE TOTAL FOR GLAZING SURFACES 634 SOLAR HEAT GAIN: Note: SCapprox = SHGC / 0.87 Shading Heat Area Coeff. Gain Description Orientation (sf) SHGF SCapprox (Btuh) Double Window East 15.5 x 73 x 0.775 = 879 Double Window East 15.5 x 73 x 0.775 = 879 EXTERIOR SOLAR TOTAL (Sext) 1758 INFILTRATION: (Type: Medium) 3300 cuft x 0.57 ac/hr x 0.018 Btu/cuft-F x 34.0 = 1153 INTERNAL GAIN (Ig): 1.00 x ( 2 x 225.0 + 600) = 1050 Dwelling Units People Appliance SUBTOTAL 6449 DUCT HEAT GAIN: Duct Location: Attic 0.10 x 6449 = 645 HVAC SIZING Page 4 HVAC prniprt Tl}lG DAruvrn Ann r_i_ nl/nw1nn nn nn n, MICROPAS6 v6.01 File -20375A6 Wth-CTZ15S92 Program -HVAC SIZING User#-MP0207 User-Madlin's Enterprises Run -NO DUCT TESTING TOTAL HOURLY SENSIBLE HEAT GAIN 7094 LATENT LOAD: 0.20 x 7094 = 1419 TOTAL COOLING LOAD 8513 Madlin-'s enteypfises Catherine M. Madlu; Certified Energy Analyst . 760-322-5004 / 323-3644 (fax) V ITT V V V V Addendums and Notes Catherine M. Madlin, Certified Energy Analyst • 760-322-5004 / 323-3644 (fax) Madlin-'s enterprises TITTTTTT Title 24 Energy Standards Table Reprint Table 7-4 — Target Floor Area of Addition Percent Leakage 100 200 300 400 500 600 700 800 900 1000 1200 1400 1600 1800 2000 for Air Distribution 1000 26 24 22 21 20 19 18 18 17 17 16 15 14 13 13 Ducts Serving 1100 26 24 23 22 21 20 19 18 18 17 16 15 14 14 13 Existing -Plus- Addition Duct 1200 26 24 23 22 21 20 19 19 18 18 17 16 15 14 14 Systems 1300 26 25 23 22 21 21 20 19 19 18 17 16 15 15 14 1400 26 25 24 23 22 21 20 20 19 18 17 17 16 15 15 1500 26 25 24 23 22 21 21 20 19 19 18 17 16 16 15 1600 26 25 24 23 22 22 21 20 20 19 18 17 17 16 15 1700 26 25 24 23 23 22 21 20 20 19 18 18 17 16 16 = 1800 26 25 24 24 23 22 21 21 20 20 19 18 17 17 16 rn E N 1900 26 25 25 24 23 22 22 21 20 20 19 18 17 17 16 W 2000 26 26 25 24 23 22 22 21 21 20 19 18 18 17 17 m 2100 27 26 25 24 23 23 22 21 21 20 20 19 18 17 17 Q 2200 27 26 25 24 23 23 22 22 21 21 20 19 18 18 17 0 2300 27 26 25 24 24 23 22 22 21 21 20 19 18 18 17 LL 2400 27 26 25 24 24 23 23 22 22 21 20 19 19 18 18 Fes- 2500 27 26 25 24 24 23 23 22 22 21 20 20 19 18 18 2600 27 26 25 25 24 23 23 22 22 21 21 20 19 19 18 2700 27 26 25 25 24 24 23 22 22 22 21 20 19 19 18 2800 27 26 25 25 24 24 23 23 22 22 21 20 20 19 18 2900 27 26 25 25 24 24 23 23 22 22 21 20 20 19 19 3000 27 26 26 25 24 24 23 23 22 22 21 21 20 19 19 3100 27 26 26 25 24 24 23 23 23 22 21 21 20 19 19 3200 27 26 26 0 25 24 24 23 23 22 22 21 20 20 19 Note: These target percentages are based on the existing house being constructed before 1999, e.g. the default leakage is 28%. Values are rounded down to the nearest whole percentage. • P.O. Box 1443 • Palm Springs, Ca 92263-1443 v E-mail. Cmadlin@aol.com Y cl- -4 cv C\IL eA 43 cl- -4 cv Madlin 's enterptises Catherine M. Madlin, Certified Energy Analyst • 760-322-5004 / 323-3644 (fax) ....... Manufacturer's Specifications i Madlin's enterpnses Catherine M. Madlin, Certified Energy Analyst Y 760-322-5004 / 323-3644 (fax) ....... Title 24 Energy Standards Table Reprint Table 2-6. a ault enestration Product U -Values (this table to be used by manufacturer's to establish a U -value rating without performance testing) Single PaneFDoublePane Frame Type] Product Type U -value ue2 , Metal Operable 1.28 0.87 Metal Fixed 1.19 0.72 Metal Greenhouse/Garden window 2.26 1.40 Metal Doors 1.25 0.85 Metal Skylight 1.72 0.94 Metal, Thermal Break Operable 0.71. Metal, Thermal Break Fixed 0.60 Metal, Thermal Break Greenhouse/Garden window 1.12 Metal, Thermal'Break Doors 0.64 Metal, Thermal Break Skylight 0.80 on- eta Operable 0.99 0.6 Non -Metal Fixed 1.04 0.57 Non -Metal Doors 0.99 0.55 Non -Metal Greenhouse/Garden windows 1.94 1.06 Non -Metal Skylight 1.47 0.68 1. Metal includes any field -fabricated product with metal cladding. Non-metal framed manufactured fenestration products with metal cladding must add 0.04 to the listed U - value. Non -Metal frame types can include metal fasteners, hardware, and door thresholds. Thermal break product design characteristics are: a. The material used as the thermal break must have a thermal conductivity of not more than 3.6 Btu-inch/hr/ft2/°F, b The thermal break must produce a gap of not less than 0.210", and c All metal members of the fenestration product exposed to interior and exterior air must incorporate a thermal break meeting the criteria in (a) and (b) above. In addition, the fenestration product must be clearly labeled by the manufacturer that it qualifies as a thermally broken product in accordance with this standard. 2. For all dual glazed fenestration products, adjust the listed U -values as follows: a. Subtract 0.05 for spacers of 7/16" or wider. b. Subtract 0.05 for products certified by the manufacturer as low -E glazing. C. Add 0.05 for products with dividers between panes if spacer is less than 7/16" wide. d. Add 0.05 to any product with true divided lite (dividers through the panes). • P.O. Box 1443 v Palm Springs, Ca 92263-1443 v E-mail: Cmadlin@aol.com Y