09-0331 (SOTB)P.O. BOX 1504
78-495 CALLE TAMPICO
LA QUINTA, CALIFORNIA 92253
Application Number: 09-00000331
Property Address: 55915 TURNBERRY WY
APN: 767-560-005- - -
Application description: STRUCTURES OTHER THAN BUILDINGS
Property Zoning: LOW DENSITY RESIDENTIAL
Application valuation: 3000
Applicant:. Architect or Engineer:
BUILDING & SAFETY DEPARTMENT
BUILDING PERMIT
--------------------------------------------------
LICENSED CONTRACTOR'S DECLARATION
I hereby affirm under penalty of perjury that I am licensed under provisions of Chapter 9 (commencing with
Section 7000) of Division 3 of the Business and Profe . e, �myense is in full force and effect.
License Clas�s:j/B License 42
Dat ' r�>t b ntractor.
OWNER -BUILDER DECLARATION
hereby affirm under penalty of perjury that I am exempt from the Contractor's State License Law for the
following reason (Sec. 7031.5, Business and Professions Code: Any city or county that requires a permit to
construct, alter, improve, demolish, or repair any structure, prior to its issuance, also requires the applicant for the
permit to file a signed statement that he or she is licensed pursuant to the provisions of the Contractor's State _
License Law (Chapter 9 (commencing with Section 7000) of Division 3 of the Business and Professions Code) or,
that he or she is exempt therefrom and the basis for the alleged exemption. Any violation of Section 7031.5 by
. any applicant for a permit subjects the applicant to a civil penalty of not more than five hundred dollars ($500).:
(_) I, as owner of the property, or my employees with wages as their sole compensation, will do the work, and
the structure is not intended or offered for sale (Sec. 7044, Business and Professions Code: The
Contractors' State License Law does not apply to an owner of property who builds or improves thereon,
and who does the work himself or herself through his or her own employees, provided that the
improvements are not intended or offered for sale. If, however, the building or improvement is sold within
one year of completion, the owner -builder will have the burden of proving that he or she did not build or
improve for the purpose of sale.).
(_ 1 I, as owner of the property, am exclusively contracting with licensed contractors to construct the project (Sec.
7044, Business and Professions Code: The Contractors' State License Law does not apply to an owner of
property who builds or improves thereon, and who contracts for the projects with a contractor(s) licensed
pursuant to the Contractors' State License Law.).
1 1 I am exempt under Sec. , B.&P.C. for this reason
Date: Owner:
CONSTRUCTION LENDING AGENCY
I hereby affirm under penalty of perjury that there is a construction lending agency for the performance of the
work for which this permit is issued (Sec. 3097, Civ. C.I.
Lender's Name: '
Lender's Address:
LQPERMIT
Owner:
STEVE FOUNTAIN
55915 TURNBERRY WAY
LA QUINTA, CA 92253
Contractor:
DURKTON, MARK
69683 PLEASANT GROVE
CATHEDRAL CITY, CA 9
(760)328-7276
Lic.'No.: 505442
VOICE (760) 777-7012
FAX (760) 777-7011
INSPECTIONS (760) 777-7153
Date: 4/14/09
APR 3 0 2009 ID
CITYdF LA
---------------------------
WORKER'S COMPENSATION DEC T'
I hereby affirm under penalty of perjury one of the following declarations:
I have and will maintain a certificate of consent to self -insure for workers' compensation, as provided
for by Section 3700 of the Labor Code, for the performance of the work for which this permit is
issued.
I have and will maintain workers' compensation insurance, as required by Section 3700 of the Labor
Code, for the performance of the work for which this permit is issued. My workers' compensation
insurance carrier and policy number are:
Carrier EXEMPT Policy Number EXEMPT
I certify that, in the performance of the work for which this permit is issued, I shall not employ any
person in any manner so as to become subject to the workers' compensation laws of California,
and agree that, if I should become subject to the workers' compensation provisions of Section
3700 of the Labo1lC�CgI1 e, h with comp y those provisions.
ate licanr. 1 I
WARNING: FAILURE TO SECURETVWORKERS' COMP TION COVERAGE IS UNLAWFUL, AND SHALL
SUBJECT AN EMPLOYER TO CRIMINAL PENALTIES AND CIVIL FINES UP TO ONE HUNDRED THOUSAND
DOLLARS ($100,000). IN ADDITION TO THE COST OF COMPENSATION, DAMAGES AS PROVIDED FOR IN ,r
SECTION 3706 OF THE LABOR CODE, INTEREST, AND ATTORNEY'S FEES.
APPLICANT ACKNOWLEDGEMENT
IMPORTANT Application is hereby made to the Director of Building and Safety for a permit subject to the
conditions and restrictions set forth on this application.
1. Each person upon whose behalf this application is made, each person at whose request and for
whose benefit work is performed under or pursuant to any permit issued as a result of this application,
the owner, and the applicant, each agrees to, and shall defend, indemnify and hold harmless the City
of La Quinta, its officers, agents and employees for any act or omission related to the work being
performed under or following issuance of this permit.
2. Any permit issued as a result of this application becomes.null and void if work is not commenced
within 180 days from date of issuance of such permit, or cess rk for 180 days will subject
permit to cancellation.
I certify that 1 have read this application and state that the above inf mation is correct. agree to comply with all
city and county ordinances and state laws relating to building co n, and hereby resen
of t county to enter upo the above-mentioned prop rty fo i e ion p
Date• nature (Applicant or Agent):
Application Number . . . . . 09-00000331
Permit . . .
BUILDING PERMIT
Additional desc .
Permit Fee . . . .
54.00
Plan'Check Fee
35.10
Issue Date . . . .
Valuation . . .
. 3000
Expiration Date
10/11/09
r Qty Unit Charge
Per
Extension
BASE FEE
45.00
1.0.0 9.0000
----------------------------------------------------------------------------
THOU BLDG 2,001-25;000
9.00
Permit . . .
MECHANICAL
Additional desc..
Permit Fee . . . .
21.50
Plan Check Fee
5.38
Issue Date . . . .
Valuation . . .
. 0
Expiration Date
10/11/09
Qty Unit Charge
Per
Extension
BASE FEE
15.00
1.00 6.5000
----------------------------------------------------------------------------
EA MECH OTHER
MECH EQUIPMENT
6.50
Permit . . .
PLUMBING
Additional desc .
Permit Fee . . . .
18.00
Plan Check Fee
4.50
Issue Date . . . .
'Valuation . . .
. 0
Expiration Date
10/11/09
Qty Unit Charge
Per
Extension
BASE FEE
15.00
1.00 3.0000
EA PLB GAS PIPE
1-4 OUTLETS
3.00
----------------------------------------------------------------------------
Special Notes and Comments
ADD VENT -FREE EXTERIOR
FIREPLACE WITH
ENCLOSURE AT REAR"PATIO
=
---------------------------
Other Fees . . . . .
------------------------------------------------
. . . . BLDG STDS ADMIN (SB1473)
1.00
ENERGY
REVIEW FEE
3.51
Fee summary Charged
---------------------------
Paid
----------
Credited
--------------------
Due ,
Permit Fee Total
93.50
.00 .00
93.50
Plan Check Total
44.98
.00 .00
44.98
Other Fee Total
4.51
.00 00
4.51
Grand Total
142.99
.00 .00
142.99
LQPERMIT
�- GO'. '` ,' 1.• F`'SITA
FAIRWAYS ASSOCIATION
March 13, 2009
Steve & Marcia Fountain
P.O. Bog 5940
La Quinta, CA 92248
Re: Architectural Application- 55-915 Tumberry Way - APPROVAL
Dear Mr. & Mrs. Fountain:
The Architectural Committee reviewed your,plans submitted for the vent free fireplace and
art niche.
I am pleased to notify you that the Architectural Committee has approved your application
as submitted
If you should have any questions in regard to this correspondence please do not hesitate to
contact the Association at any time. _
Sincerely,
On Behalf of the PGA WEST Association
A rhitectural I I.an&cape Committee daj-
By: Jamie Saldivar
PGA WEST Fairways Operations Manager
For the Architectural Committee
Cc: File
Post Office Box 1690 - La Quinta, California 92247 - Phone (760) 776-5100 - Fax (760) 776-5111
A.
i
Napoleon GSS36N 36" Vent -Free Outdoor Fireplace 40,060 BTU's
Page l' of 3
p ( m I My Account -I Memberships I Contact Us I Helo
Ventin Dlre( t. J Cart ��—
�Trurar�kAWftua3sap*,s,om ;' CheckOUt�
0 Items 'a '
Home Range Hoods Bath Fans Heating Ventilation Air Conditioners Skylights Brands SALE
Call Us Toll Free (800) 482-3514 1 * 5EARCH
A.
_. .. s..
Li
AIR `OUTDOOR
,CONDITIONERS . >{Ef{T1I<ICa .. , ..:..: REGISTERS ,:, RANGEHOODS
EXHAUST FANS . THERMOSTATS VENTILATION
You are: Home > Brands > Napoleon > Fireplaces > Napoleon «Back to Search Results Print Page Bookmark
GSS36N
Napoleon GSS36N 36" Vent -Free Outdoor Fireplace 40,000 BTU's
t\ l
4UALITY FIREPLACES
Watch ~. Zoom ._ 360 ' -� Audio
Movie Image View Details
Product Details for the Napoleon GSS36N
$1,889.10
Originally $2,099.00, You Save 10%
Shipping: Free Shipping on LTL freight
orders over $1,999.00! See Details
In stock items generally ship in 3 to 4
6t ARAs days.
Stainless Steel
Finish:
•
field Tet CA
13131300 Be the first Live Chat
to review this product Send to a Friend
Return Policy 1 Ask A Question
110% Low Price Guarantee
36" Vent -Free Outdoor Fireplace. For quality outdoor living nothing sets
the standard like the GSS36N. This stunning stainless steel outdoor
fireplace requires no venting and installs almost anywhere! An optional
remote control is also available
• 100% stainless steel construction
• Protective stainless steel cover included
• Up to 40,000 BTU's and 99.9% efficiency
• Stainless steel upper and lower louvers
• LP conversion kit is available
• Millivolt remote control valve with built-in adjustable flame heat control
• Zero clearance to combustibles
Technical Specs
BTU Output
40000
Depth
13.75
Efficiency
99.90%
Fuel Type
Natural Gas
Height
33, 35.5
Overall (W x H x
37 3/4" x 33"
D)
x 13 3/4"
Vent Free
Yes
Visible Height
33
http://www.ventingdirect.com/index.cfnVpage/product:display/productld/GSS36N/manufact... 4/7/2009
t
Specifications
• 40,000 BTUs 33th• . t -
}G
• 99.9% Efficiency
• Natural Gas
37 3r,
Natural Gas to Propane conversion kit
• 12" stainless steel gas flex connector and shut off
(25/crtn) _-
• Tested in Canada and the US as an outdoor gas `VVVI
fireplace
• Listed to UL CR97-003 and CSA CAN 1-2.21 and
IASUS4
• 54S GAS
Min
Tested in Canada and the US as an outdoor gas fireplace T
Listed to UL CR97-003 & CSA CAN 1-2.21 & IASUS4
' ' _ .Line dimenstons`are to'be used'as'a.gutde only Please cgnsuit your insLallahon nianual,:�,,
`r t,fgr updated aid,precisetmeasuremeuts before proeeediog to install or, frame your. Napoleon F>repla�es �r.. d
Check atI Locat and Naiaonatr�uildm' `Codes and Gas:Re Cations'
ri
CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS, CR97-003, CAN1-2.21-M65, IAS U.S. 4-96.
QUALITY FIREPLACES
0 if
Awiem000a W440V� PU44eU
OUTDOOR GAS APPLIANCE
INSTALLATION AND OPERATION INSTRUCTIONS FOR
OUTDOOR GAS FIREPLACE
NATURAL GAS MODEL GSS36N
PROPANE GAS MODEL GSS36P
CERTIFIED FOR CANADAAND UNITED STATES USING ANSI 1 CSA METHODS
WARNING: If the information in these instructions is not followed exactly, a fire or
explosion may result causing property damage, personal injury or death.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapours and liquids in the vicinity of
this or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance. • Immediately call your gas supplier from
• Do not touch any electrical switch. a neighbour's phone. Follow the gas
• Close propane bottle or shut-off gas supplier's instructions.
supply. • If you cannot reach your gas supplier,
• Do not use any phone in your build call the fire department.
ing or near the appliance.
Installation and service must be performed by a qualified installer, service agency or
the gas supplier.
THIS FIREPLACE MUST BE INSTALLED OUTSIDE.
APPLY SERIAL NUMBER LABEL FROM CARTON
Ah'`pifJtib,, �e,1TaLlY j
HPBA 'SD C`F�1uS ` Sari al Nn, X X X X X X 0 0 0 0 0 0 17-71
900, -2000 d'�.�Ln.�• MODEL NO.
W415-0369 / E / 02.16.07
.2
PG 3-4 INTRODUCTION'
9 OPERATION / MAINTENANCE
Warranty
Operating Instructions
General Instructions
Maintenance
General Information
Venturi Adjustment
5-6 INSTALLATION
10 REPLACEMENTS
Gas Installation
Ordering Replacement Parts
Combustion and Ventilation Air Provisions
Replacement Parts
Clearance to Combustibles
11-12 TROUBLE SHOOTING GUIDE
Framing
Mantle Clearances
Nailing Tab Installation
7-8 FINISHING
Log Placement
Curtain Mesh
Hood Installation
Logo Placement
Louvre Installation
PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE
IIWARNING II
• Under no circumstances should this fireplace be modified.
• Provide adequate ventilation and combustion air. Provide adequate accessibility clearance for servicing
and operating the fireplace. Never obstruct the front opening of the fireplace.
• If fireplace keeps shutting off, have it serviced. Keep burner and control compartment clean.
• Do not burn wood or other materials in this fireplace.
• Adults and especially children should be alerted to the hazards of high surface temperatures and should
stay away to avoid burns or clothing ignition. Keep young children and animals away when the fireplace
is hot.
• Clothing or other flammable material should not be placed on or near the fireplace.
• Any safety screen or guard removed for servicing must be replaced prior to operating the fireplace.
• It is imperative that the control compartments, burners and circulating air passageways in the fireplace
are kept clean. The fireplace should be inspected before use and at least annually by a qualified service
person. The fireplace area must be kept clear and free from combustible materials, gasoline and other
flammable vapours and liquids.
• Furniture or other objects must be kept a minimum of 4 feet away from the front of the fireplace.
• Do not use this fireplace if any part has been under water. Immediately call a qualified service technician
to inspect the fireplace and to replace any part of the control system and any gas control which has been
under water.
• Do not allow wind to blow directly into the fireplace. Avoid any drafts that alter burner flame patterns.
• Do not use any accessory not approved for use with this fireplace.
ANY CHANGE TO THIS FIREPLACE OR ITS CONTROLS CAN BE DANGEROUS
AND IS PROHIBITED.
No I t: Changes, other than editorial, are denoted by a vertical line in the margin.
W415-0369 / E / 02.16.07
3
NAPOLEON® gas appliances are manufactured under the strict Standard of the world recognized
ISO 9001 : 2000 Quality Assurance Certificate.
NAPOLEON® products are designed with superior components and materials, assembled by trained
craftsmen who take great pride in their work. The burner and valve assembly are leak and test -fired at a
quality test station. Once assembled the complete appliance is thoroughly inspected by a qualified technician
before packaging to ensure that you, the customer, receives the quality,product that you expect from
NAPOLEON' .
NAPOLEON® GAS APPLIANCE 5 YEAR LIMITED WARRANTY
All stainless steel components of your new NAPOLEON°gas appliance are warranted against defects for
five years.
All parts such as gas valves, logs, gasketing are covered and NAPOLEON® will provide replacement parts
free of charge, during the first year of the limited warranty.
Labour related to warranty repair is covered free of charge during the first year. Repair work, however,
requires the prior approval of an authorized company official. Labour costs to the account of NAPOLEON°
are based on a predetermined rate schedule and any repair work must be done through an authorized
NAPOLEON'dealer.
CONDITIONS AND LIMITATIONS
NAPOLEON® warrants its products against manufacturing defects to the original purchaser only — i.e., the individual or legal entity (registered customer) whose name appears
on the warranty registration card filed with NAPOLEON® -- provided that the purchase was made through an authorized NAPOLEON® dealer and is subject to the following
conditions and limitations:
This limited warranty applies only while the unit remains at the site of original installation, and only if the unit is installed in Canada or the United States.
This factory warranty is nontransferable and may not be extended whatsoever by any of our representatives.
Installation must be done in accordance with the installation instructions included with the product and all local and national building and fire codes.
This limited warranty does not cover damages caused by misuse, lack of maintenance, accident, alterations, abuse or neglect and parts installed from other manufacturers will
nullify this warranty.
This limited warranty further does not cover any scratches, dents, corrosion or discolouring caused by excessive heat, abrasive and chemical cleaners, mechanical breakage
of logs and embers.
In the first year only, this warranty extends to the repair or replacement of warranted parts which are defective in material or workmanship provided that the product has been
operated in accordance with the operation instructions and under normal conditions.
After the first year, with respect to this Limited Warranty, NAPOLEON® may, at its discretion, fully discharge all obligations with respect to this warranty by refunding to the original
warranted purchaser the wholesale price of any warranted but defective part(s).
After the first year, NAPOLEON®w ll not be responsible for installation, labour or any other costs or expenses related to the reinstallation of a warranted part, and such expenses
are not covered by this warranty.
Notwithstanding any provisions contained in this Limited Warranty, NAPOLEON'S responsibility under this warranty is defined as above and it shall not in any event extend to
any incidental, consequential or indirect damages.
This warranty defines the obligations and liability of NAPOLEON® with respect to the NAPOLEON® gas appliance and any other warranties expressed or implied with respect
to this product, its components or accessories are excluded.
This limited warranty does not cover damages resulting from the use of components not supplied with the appliance, or the use of fuel other than those specified.
Any damages to appliance due to weather, long periods of dampness, condensation, damaging chemicals or cleaners will not be the responsibility of NAPOLEON&
The bill of sale or copy will be required together with a serial number and a model number when making any warranty claims from your authorized dealer. The warranty registration
card must be returned within fourteen days to register the warranty.
NAPOLEON® reserves the right to have its representative inspect any product or part thereof prior to honouring any warranty claim.
W415-0369 / E / 02.16.07
rd
THIS GAS FIREPLACE SHOULD BE INSTALLED AND
SERVICED BYA QUALIFIED INSTALLER to conform with
local codes. Installation practices vary from region to region
and it is important to know the specifics that apply to your
area.
Installation practices vary from region to region and it is
important to know the specifics that apply to your area, for
example: in Massachusetts State:
• The appliance off valve must be a `T handle gas cock.
• The flexible connector must not be longer than 36 inches.
• The appliance is not approved for installation in a bedroom
or bathroom unless the unit is a direct vent sealed combustion
product.
• WARNING: This product must be installed by a licensed
plumber or gas fitter when installed within the commonwealth of
Massachusetts.
• Un -vented room heater shall be installed in accordance with 527
CMR 30.00 and 248 CMR 3.00 through 7.00.
• Sellers of un -vented propane or natural gas-fired space/room
heaters shall provide to each purchaser a copy of 527 CMR 30.00
upon the sale of the unit from
httpYlwww.napoleonfirep/aces.com1webshare/installation manualsi
mass requirements.pdf
• A carbon monoxide detector is required in all rooms containing
gas fined appliances.
The installation must conform with Local codes or in the
absence of local codes, with the National Fuel Gas Code
ANSI Z223.1 /IN FPA 54 in the United States or CSA B149.1,
Natural and Propane Installation code in Canada.
The fireplace and its individual shutoff valve must be discon-
nected from the gas supply piping system during any pressure
testing of that system at test pressures in excess of 1/2 psig
(3.5 kPa). The fireplace must be isolated from the gas supply
piping system by closing its individual manual shutoff valve
during any pressure testing of the gas supply piping system
at test pressures equal to or less than 1/2 psig (3.5 kPa).
When the fireplace is installed directly on combustible mate-
rial other than wood flooring, the fireplace shall be installed on
a metal or wood panel extending the full width and depth.
35 W
33"
W415-03691 E / 02.16.07
FOR YOUR SATISFACTION, THIS FIREPLACE HAS BEEN
TEST -FIRED TO ASSURE ITS OPERATION AND QUAL-
ITY! Maximum input is 40,000 BTU/hr for natural gas and
propane. When the fireplace is installed at elevations above
2,000ft, and in the absence of specific recommendations
from the local authority having jurisdiction, the certified high
altitude input rating shall be reduced at the rate of 4% for
each additional 1,000ft.
It is highly recommended to protect the logs from mois-
ture (rain, snow). Cover the rfrebox when not in use.
This (replace is only for use with the type of gas indi-
cated on the rating plate. This rfreplace is not convertible
for use with other gases, unless a certified kit is used.
Minimum inlet gas supply pressure is 4.5 inches water col-
umn for natural gas and 11 inches water column for propane.
Maximum inlet gas pressure is 7 inches water column for
natural gas and 13 inches water column for propane. Manifold
pressure under flow conditions is 3.5 inches water column for
natural gas and 10 inches water column for propane.
No external electricity (110 volts or 24 volts) is required
for the gas system operation.
Expansion / contraction noises during heating up and cooling
down cycles are normal and are to be expected.
Use only accessories designed for and,
listed with your specific fireplace.
NATIONAL
FIREPLACE
We recommend that our gas
INSTITUTE'
hearth products be installed
and serviced by profes-
sionals who are certified in
the U.S. by the National
Fireplace Institute® (NFl) as
CERTIFIED
NFI Gas Specialists.
www.nficartdiod.org
5'la" GAS
INLET
3"
T
�2r
N1 12j 1a" 13 Ile
I. 31 ala"
INSTALLATION
NOTE. If the unit is installed using a propane cylinder
as a source of fuel, the cylinder must be retained. A
stand for a standard 201b cylinder is available from your
NAPOLEON® Dealer.
1: Move the fireplace into position and secure using the
nailing tabs and/or secure to the floor through the '14"o holes
located at either end of the base.
2. Install rigid black pipe, 1/2" type -L copper tubing or, if
local codes permit, a 3/8" flex connector and shutoff valve
to the gas line and the fireplace gas valve. Seal and tighten
securely. An adapter fitting is required between the gas valve
and the copper tubing or flex connector.
DO NOT KINK FLEX CONNECTOR.
FLEXIBLE SHUT OFF
�105N ECTOR VALV
A AP 'R
FITTING
FiC;i1RF: 2 CK
3. Check for gas leaks by brushing on a soap and water
solution.
DO NOT USE OPEN FLAME.
4. For ease of accessibility, an optional remote wall switch
may be installed in a convenient location. Route a 2 strand,
solid core millivolt wire through the electrical hole located at
the bottom left side of the unit. The recommended maximum
lead length depends on wire size:
WIRE SIZE MAX. LENGTH
14gauge 100 feet
16gauge 60 feet
18gauge 40 feet
Attach the two leads to terminals 1 and 3 located on the
gas valve.
0
Do not connect either the wall switch, thermostat or gas
valve to electricity (110 volts).
5
This fireplace is intended for installation on an outdoor patio
or in your yard. It must never be installed inside the warm air
envelope of your structure.
It is highly recommended that this fireplace be installed in a
"sheltered" area. Direct wind will cause an erratic flame and
possible pilot or main burner outage.
An erratic flame could also lead to excessive carboning
(black soot), this condition is not a safety issue but is visu-
ally undesirable.
Typical installation may include covered patio, screened
porch, gazebo or an outside the wall of a house.'
NOTE: Ensure the area has adequate ventilation.
Sides, back, bottom & top 0 inches
Recessed 13% inches
Top of unit to ceiling 48
It is recommended that the walls of the fireplace enclosure be ,
finished. This would ensure that clearance to combustibles
is maintained within the cavity.
"If installing a propane fireplace the propane cylinder
must always be on the exterior of such a structure.
W415-0369 / E 102.16.07
When roughing in the fireplace, .raise the fireplace to ac-
commodate for the thickness of the finished floor materials,
It is best to frame your fireplace after it is positioned. Use i.e. tile, carpeting, hard wood, which if not planned for will
2x4's and frame to local building codes. FIGURE 4-6. interfere with the opening of the lower access door and the
FiC installation of many decorative flashing accessories.
Objects placed in front of the fireplace should be kept a
minimum of 4 feet away from the front face.
MANTLE CLEARANCES
Combustible mantle clearance can vary according to the
mantle depth. Use the graph to help evaluate the clearance
needed.
35 314 F!GI� . '�jIII jI'�'�f'''
I 1 / - "\1AkI . rl ift 111 '
17" 1 4W
16" 2 K
14"12_
TOP OF UNIT
17
16
15
14
13
12
MANTLE WIDTH
LE
COMBUSTIBLE
E MATERIALS
STUD
II
FiGT?RF:. 9 '
OUT SIDE +
314
To install the fireplace face
flush with the finished sur -
CHASE
13
face, position the framework
.
E
to accommodate the thick-
ness of the finished surface.
Bend out the four nailing
37.112'„
tabs, attached on either side _
FiCiIRF 7
of the fireplace and.secure _
to the 2x4 framing. The '.
tabs will facilitate the instal-'
13 31a" :rim
INSIDE
lation of either a 3/4^ or a 1"
CHASE
finished surface thickness.
t
The nailing tabs must not
I
be removed.
�---- 371/2 6"
2MIN.
4
Combustible materials may be installed flush with the front
of the fireplace but must not cover any of the outer frame
face -areas of the fireplace. Non-combustible material (brick,
stone or ceramic tile) may protrude in these areas.
It is not necessary to install a hearth extension with this
fireplace system.
W415-0369 / E / 02.16.07
9
FINISHING
LOG PLACEMENT
PHAZERT"".logs.are exclusive to NAPOLEON® Fireplaces;
arid.provde a unique'and realistic glowing effect that is'dif-' ;
ferent;in,every, installation: .
Log colours may vary. During the initial use'of the fireplace, .'..
,
the colours will become'more uniform:as'colour pigments,
burn in'during the heat activated curing process `
FiGiJ
,
:
a
x
3. Place the bottom of fhe left crossover log, (#4) against
the left fireboxsideana pulled forward tothe grate :.
The op of the log should rest.in the-pocket on the back log
.y
i. Place.the.back log (#1) onto the log
support,tray and in front of the tabs.•The
'
A�IDE�IEVV,
�Aabs'maintain an,airaspace between the,',,
• `log and'freboz back'io facilitate combus=
'
-tion air-.flow. Ensure that the of'the
,back
: log rests against the brackets"on the back
° f
lT B wall of the firebox
_
4.. Position the notch located on the endof,the center log
(#5) againstthe middle grate post. with the other end of ttie
'of=the
log resting in the' left crossover lo'g.
5 Place.th6 bottom of the right crossover'iog (#6),against
9
the right firebox "side 'and pulled forward to the grate. The top .
' f the log should rest in. the pocket provided on the center";
.,log {#5)
'
Blocked burner portscan°cause an incorre'ct'flame pattern,. .
carbon deposits and delayed ignition. PHAZERT" log s.glow • ..,
'wher,expose. to direct flam6 PHAZERT-"':logs available from' .
2. Move the two small logs (#2 & #3) into position,. lining
your NAPOLEON® .dealer.
"up
the studs located on`the burner with theholes on the bottom
of the Iogs.,Ensure` that the small logs,sit flat on the burner.IMPORTANT
" _
IT IS HIGHLY'RECOMMENDED TO'PROTECT
-
"'.THE LOGS FROM-MOISTURE
" r
COVER�.THE FIREBOX WHEN NOT IN USE.
W415 0369 l E f 02.16.07
I
The curtain mesh must be kept fully closed during operation
to ielp prevent accidental burns from occurring.
The heater must not be used when the hood is re-
moved. Hook the hood over the lip of the curtain support
plate.
W415-0369 / E / 02.16.07
Remove the
backing of the
logo supplied
and place on the
screen cover, as
indicated.
L PPER LOUVRES: Insert
HOOD the upper louvres- i ee
slots :)n bo:h brackets.
BRACKET Fress the top flange -rf
SLOT . the hood intothe four c ips
located aloN the top -f
er A,_r,....:,,,� . the urit as shown..
LOWER LOUVRES: -At-
tach each hinge to tf a
firebox with 2 screws.
HINGE SCREEN: Position the nince screen into place ar•d
with the control door =open, secure b the firebo-( usieg three
screws.
NJ
OPERATION / MAINTENANCE
If heater keeps shutting off, have it serviced. Keep burner After extended periods of non -operation such as follow -
and control compartment clean. ing a vacation or a warm weather season, the fireplace
When lit for the first time, the fireplace will emit a slight may emit a slight odour for a few hours. This is caused
odour for a few hours. This is a normal temporary condi- by dust particles burning off.
tion caused by the curing of the logs and the "bum -in" of
internal paints and lubricants used in the manufacturing
process and will not occur again.
A. This fireplace is equipped with a pilot which must be lit by hand
while following these instructions exactly.
B. Before operating smell all around the fireplace area for gas
and next to the floor because some gas is heavier than air and
will settle on the floor.
C. Use only your hand to tum the gas control knob / manual
shut-off knob. Never use tools. If the knob will not tum by hand,
do not try to repair it. Call a qualified service technician. Force or
attempted repair may result in a fire or explosion.
D. Do not use this fireplace if any part has been under water. Im-
mediately call a qualified service technician to inspect the fireplace
and replace any part of the control system and any gas control
which has been under water.
• Do not use a mobile or land phone.
• If you cannot reach your gas supplier, call the fire department.
• Turn off all gas to the fireplace.
• Do not try to light any appliance.
• Immediately call your gas supplier from a
neighbour's phone. Follow the gas supplier's instructions.
MAINTENANCE
CAUTION: Label all wires prior to disconnection when servic-
ing controls. Wiring errors can cause improper and dangerous
operation. Verify proper operation after servicing. This heater
should be inspected and serviced before use and at least an-
nually by a qualified service person. The fireplace area must
be kept clear and free of combustible materials, gasoline or
otherflammable vapours and liquids. The flow of combustion
and ventilation air must not be obstructed.
2. Keep the control compartment, logs, burner, air shutter
opening and the area surrounding the logs clean by vacuum-
ing or brushing, at least once a year.
3. Check to see that all burner ports are burning. Clean out
any of the ports which may not be burning or are not burn-
ing properly.
4. Check to see that the pilot flame is large enough to engulf
the thermocouple and thermopile and promptly ignites the
main burner.
6. Check to see that the main burner ignites completely on all
openings when the gas knob for the burner is turned on. A 5 to
10 second total light -up period is satisfactory. If ignition takes
longer, consult your NAPOLEON® dealer / distributor.
Cleaning Stainless Steel: Do not use abrasive cleaners to
clean any painted, porcelain or stainless steel parts. To clean
stainless surfaces, use a stainless steel cleaner or a non-
abrasive cleaner. Always wipe in the direction of the grain.
When lighting and re -lighting, the gas knob cannot be turned
from pilot to off unless the knob is depressed.
1. Stop! Read the safety information on the operating label.
2. Tum the gas knob clockwise /ter to off.
3. Wait five (5) minutes to clear out any gas. If you smell gas
including near the floor, stop! Follow "b" on the operating label.
If you don't smell gas go to the next step.
4. If fireplace is equipped with flame adjustment valve turn
clockwise to off.
5. Find pilot located in front of back log.
G. Turn gas knob counter -clockwise to pilot.
7. Depress and hold gas knob while lighting the pilot with the
push button igniter. Keep knob fully depressed for one minute,
then release. If pilot does not continue to burn repeat steps 3
through 7.
8. With pilot lit, tum gas knob counter -clockwise *--\ t o
on.
9. If equipped with flame adjustment valve, push and turn knob
to high.
10. If equipped with remote on-off switch, main burner may not
come on when you turn the valve to on or high. Remote switch
must be in the on position to ignite burner.
• Push in gas control knob slightly and tum clockwise /e .A to
off. Do not force.
Do not use steel wool, as it will scratch the finish. Stainless
steel parts will discolour when heated, usually to a golden or
brown colour. This discolouration is normal and will not affect
the performance of the appliance.
Air shutter adjustment must only be done by a quali-
fied gas installer!
Closing the air shutter will cause a more yellow flame, but
can lead to carboning. Opening the air shutter will cause a
more blue flame, but can cause flame lifting from the burner
ports. The flame may not appear yellow immediately; allow
15 to 30 minutes for the final flame colour to be established.
Opening the air shutter will also reduce exhaust odours. See
Trouble Shooting Guide.
AIR SHUTTER!
OPENING
VLN IURI
AIR SHUTTER_
OPENINGS F-='
NG 3/16" FiC ORIFICE
LP 1/4"
_ 1-0-
W415-0369 / E / 02.16.07
" WARNING: This is a fast acting thermocouple. It is an integral safety component. ,
Replace only with a fast acting thermocouple supplied by Wolf Steel Ltd.
10
Y
...Contact your, dealer for questions' concerning prices and
When ordering replacement parts always give the following '
policies on replacement parts. Normally all parts can be
information:
ordered our through NAPOLEON® dealer or distributor.
9 Y r -
1.
MODEL &SERIAL NUMBER OF FIREPLACE
2.
INSTALLATION DATE OF FIREPLACE T
,.
3.
PART NUMBER
FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF.
4.
DESCRIPTION OF PART
THE ORIGINAL INVOICE WILL BE REQUIRED -TO HONOUR,
5.
FINISH
1 "
THE CLAIM.
IDENTIFIES ITEMS WHICH ARE NOT ILLUSTRATED. FOR FURTHER INFORMATION, CONTACT YOUR NAPOLEON® DEALER.
REPLACEMENT
# PART NO. DESCRIPTION -
PARTS
PAN BURNER
15
W010-1066
1 W357-0001 PIEZO IGNITER
16
W455-0078
#31 NATURAL GAS BURNER ORIFICE '
2 W680-0004 THERMOPILE16
W455-0042
949 PROPANE GAS BURNER ORIFICE
3 "W680-0005 THERMOCOUPLE ",
17
W335-0033
HOOD
4 W010-0800 NATURAL GAS PILOT ASSEMBLY
18
W565-0062 '
CURTAIN MESH
4 W0IO-0801 PROPANE GAS PILOT ASSEMBLY
19
W555-0040
CURTAIN ROD
5 W455-0069 NATURAL GAS PILOT INJECTOR
20'
WO80-0614
CURTAIN ROD BRACKET "
5 W455-0067 PROPANE GAS PILOT INJECTOR -
21
W500-0209
CURTAIN SUPPORT PLATE
6 W725-0028 NATURAL GAS VALVE
22
W630-0010
BLACK TASSELS
6 W725-0029 PROPANE GAS VALVE
23
W200-0135
'FIREBOX COVER
7` W385-0334 NAPOLEON® LOGO
24
N325-0036.
COVER HANDLE +
8 GL-639OD LOG SET
25'
W660-0005
SWITCH 11_
9, W135-0183OD BACK LOG (#1)
26'
W750-0109
Yle FLAG WIRE ASSEMB
10 • W135 -01840D LEFT MIDDLE LOG (#2)
27'
W750-0110
ala" FLAG WIRE ASSEMBLY
LY
11 W135-0185OD• RIGHT MIDDLE LOG (#3)
28
GVFLSS
LOUVRE KIT-STAINLESSSTEEL
-
,
.
19 w13Ln1AAr)n 1 FFT rRrI,vnvrp I nr, ltM1 -
•• - .
_
" WARNING: This is a fast acting thermocouple. It is an integral safety component. ,
Replace only with a fast acting thermocouple supplied by Wolf Steel Ltd.
11
Main burner goes
Pilot flame is not large enough
- turn up pilot flame.
out; pilot stays on.
or not engulfing the thermo-
- replace pilot assembly.
- check if the push button ignitor needs tightening.
pile
- replace the wire if the wire insulation is broken or frayed.
Thermopile shorting
- clean thermopile connection to the valve. Reconnect.
- replace the electrode if the ceramic insulator is cracked or broken.
- replace thermopile / valve.
Out of propane gas
Remote wall switch wire is too
- shorten wire to correct length or wire gauge.
long; too much resistance in
- spark gap should be 0.150" to 0.175" (5/32" to 11/64" approx.) from
the system.
the electrode tip and the pilot burner. To ensure proper electrode loca-
Faulty thermostat or switch.
- replace.
Pilot goes out when
System is not correctly - purge the gas line.
the gas knob is re-
purged.
- replace the valve.
leased.
Out of propane gas.
-fill the tank.
The gas valve has
an interlock device
Pilot flame is not large
- tum up the pilot flame.
which will not al-
enough
low the pilot burn-
Pilot flame is not engulfing the
- gently twist the pilot head to improve the flame pattern around the
er to be lit until
thermocouple.
thermocouple.
the thermocouple
Thermocouple shorting / - loosen and tighten thermocouple.
has cooled. Allow
faulty.
- clean thermocouple and valve connection.
approximately 60
- replace thermocouple.
seconds for the
- replace valve.
thermocouple to
cool.
Faulty valve.
- replace.
Pilot burning; no
Themostat or switch is de-
- connect ajumperwire across the wall switch terminals; if main burner
gas to main burner;
'HI';
fective.
lights, replace switch / thermostat.
gas knob is on
Wall switch wiring is defec-
- disconnect the switch wires & connect ajumper wire across terminals
wall switch / ther-
tive.
1 & 3; if the main burner lights, check the wires for defects and / or
mostat is on.
replace wires.
Main burner orifice is plugged. - remove stoppage in orifice.
Faulty valve.
- replace.
Pilot will not light. No spark at pilot burner
- check if pilot can be lit by a match
DIL018UAKLR
- check that the wire is connected to the push button ignitor.
fHERMOf`LLE
- check if the push button ignitor needs tightening.
RMOL
- replace the wire if the wire insulation is broken or frayed.
- replace the electrode if the ceramic insulator is cracked or broken.
- replace the push button ignitor.
Out of propane gas
- fill the tank.
Spark gap is incorrect
- spark gap should be 0.150" to 0.175" (5/32" to 11/64" approx.) from
the electrode tip and the pilot burner. To ensure proper electrode loca-
tion, tighten securing nut (finger tight plus 1/4 turn).
No gas at the pilot burner
- check that the manual valve is turned on.
- check the pilot orifice for blockage.
- replace the valve.
- call the gas distributor.
W415-0369 / E / 02.16.07
12
Pilot goes out while Gas piping is undersized. - turn on all gas appliances and see if pilot flame flutters, diminishes or
standing Main extinguishes, especially when main burner ignites.. Monitor appliance
burner is in 'OFF' supply working pressure.
position. - check if supply piping size is to code. Correct all undersized piping.
High Wind. - unit has been exposed to a high wind condition.
A "sheltered" area is recommended for the installation location.
- close mesh screens.
Flames are consist- Unit is over -fired or under- - check pressure readings:
eptly too large or fired. Inlet pressure can be checked by turning screw (A) counter -clockwise
too small. Carbon- 2 or 3 turns and then placing pressure gauge tubing over the test point.
ing occurs. Gauge should read T(minimum 4.5") water column for natural gas or
13" (11" minimum) water column for propane. Check that main burner
is operating on "HI".
Outlet pressure can be checked the same as above using screw (B).
L
i
�0 Gauge should read 3.5" water column for natural gas or 10" water column zJ for propane. Check that main burner is operating on "HI".
LJ AFTER TAKING PRESSURE READINGS, BE SURETOTURN SCREWS
° CLOCKWISE FIRMLY TO RESEAL. DO NOT OVERTORQUE.
r, ? Leak test with a soap and water solution.
Carbon is being de- Air shutter has become - ensure air shutter opening is free of lint or other obstructions.
posited on, logs or blocked
combustion cham-
ber surfaces. Flame is impinging on the - check that the logs are correctly positioned.
logs or combustion cham- - open air shutter to increase the primary air.
ber. - check the input rate: check the manifold pressure and orifice size as
specified by the rating plate values.
- close mesh screens.
Remote wall switch
is in "OFF" position;
main burner comes
on when gas knob
is turned to "ON"
position.
W415-0369 ! E / 02.16.07
Wall switch is mounted up- - reverse.
side down
Remote wall switch is ground- -replace.
ing.
Remote wall switch wire is check for ground (short); repair ground or replace wire.
grounding.
Faulty valve. - replace.
Bin #
City of La Quints
Building U Safety Division
P.O. Box 1"504, 78-495 Calve Tampico
La Quinta, CA 92253 - (760) 777-7012
Building Permit Application and Tracking Sheet
Permit #��
1
Project Address: SG Is
Owner's Name:
A. P. Number:
Address:
Legal Description:
City, ST, Zip: Lfitl SC
Contractor: M '`
Telephone: [
Address: P(sT�
Project Description:
City, ST, zip: G. Cc Gf�- 223
Telephone:'G,"+% A-1 40
State Lic. # : City Lic. #:
Arch., Engr., Designer:
��Jp,rp P
Address:
City, ST, Zip:
Telephone:
State Lic. #:
Name of Contact Person: �17bo
Construction Type: Occupancy:
Project type (circle one): New Add'n Alter Repair Demo
Sq. Ft.: # Stories: # Units:
Telephone # of Contact Person: 5t6 40k Av
I Estimated Value of Project: 1, TjcoD 0—w—
APPLICANT: DO NOT WRITE BELOW THIS LINE
#
Submittal
Req'd
Recd- ..
TRACKING PERMIT FEES
Plan Sets
Plan Check submitted
Item Amount
Structural Calcs.
Reviewed, readyr co rections
Plan Check Deposit
Truss Cales.
Called Contact Person
Plan Check Balance
Energy Calcs.
Plans picked up
Construction
Flood plain plan
Plans resubmitted
Mechanical
Grading plan
2'd Review, ready for corrections/'issue
Electrical
Subcontactor List
Called Contact Person
Plumbing
Grant Deed
Plans picked up
S.M.I.
H.O.A. Approval
Plans resubmitted
Grading
IN HOUSE:-
''d Review, ready for corrections/issue
Developer Impact Fee
Planning Approval
Called Contact Person
A.I.P.P.
Pub. Wks. Appr
Date of permit issue
School Fees
L
L
Total Permit Fees