Loading...
BCOM2018-004978-495 CALLE TAMPICO U 4ACII LA QUINTA, CALIFORNIA 92253 DESIGN & DEVELOPMENT DEPARTMENT BUILDING PERMIT Permit Type/Subtype: BUILDING COMMERCIAL/REMODEL Application Number: BCOM2018-0049 Property Address: 50855 WASHINGTON ST STE 2H APN: 770020017 Application Description: FRENCH ROTISSERIE / KITCHEN FIRE DAMAGE REMODEL Property Zoning: Application Valuation: $5,000.00 VOICE (760) 777-7125 FAX (760) 777-7011 INSPECTIONS (760) 777-7153 Owner: LQ INV 17165 NEWHOPE ST FOUNTAIN VALLEY, CA 92253 Applicant: Contractor: SIPOVAC CONSTRUCTION INC SIPOVAC CONSTRUCTION INC 72651 THEODORA LANE D 0 72651 THEODORA LANE PALM DESERT, CA 92260 JAN 2 4 2019 PALM DESERT, CA 92260 (760)567-2347 CITY OF LA QUINTA Llc. No.: 581636 DESIGN & DEVELOPMENT DEPARTMENT LICENSED CONTRACTOR'S DECLARATION I hereby affirm under penalty of perjury that I am licensed under provisions of Chapter 9 {commencing with Section 7000) of Division 3 of the Business and Professions Code, and my License is in full force and effect. License Class: License No.: 581636 Dat Contract OWNER -BUILDER DECLARATION I hereby affirm under penalty of perjury that I am exempt from the Contractor's State License Law for the following reason (Sec. 7031.5, Business and Professions Code: Any city or county that requires a permit to construct, alter, improve, demolish, or repair any structure, prior to its issuance, also requires the applicant for the permit to file a signed statement that he or she is licensed pursuant to the provisions of the Contractor's State License Law (Chapter 9 (commencing with Section 7000) of Division 3 of the Business and Professions Code) or that he or she is exempt therefrom and the basis for the alleged exemption. Any violation of Section 7031.5 by any applicant for a permit subjects the applicant to a civil penalty of not more than five hundred dollars ($500).: () I, as owner of the property, or my employees with wages as their sole compensation, will do the work, and the structure is not intended or offered for sale. (Sec. 7044, Business and Professions Code: The Contractors' State License Law does not apply to an owner of property who builds or improves thereon, and who does the work himself or herself through his or her own employees, provided that the improvements are not intended or offered for sale. If, however, the building or improvement is sold within one year of completion, the owner -builder will have the burden of proving that he or she did not build or improve for the purpose of sale.). () I, as owner of the property, am exclusively contracting with licensed contractors to construct the project. (Sec. 7044, Business and Professions Code: The Contractors' State License Law does not apply to an owner of property who builds or improves thereon, and who contracts for the projects with a contractor(s) licensed pursuant to the Contractors' State License Law.). (_) I am exempt under Sec. B.&P.C. for this reason Date: Owner: CONSTRUCTION LENDING AGENCY I hereby affirm under penalty of perjury that there is a construction lending agency for the performance of the work for which this permit is issued (Sec. 3097, Civ. C.). Lender's Name: Lender's Address: Date: 1/24/2019 WORKER'S COMPENSATION DECLARATION I hereby affirm under penalty of perjury one of the following declarations: I have and will maintain a certificate of consent to self -insure for workers' compensation, as provided for by Section 3700 of the Labor Code, for the performance of the ork for which this permit is issued. have and will maintain workers' compensation insurance, as required by Section 3700 of the Labor Code, for the performance of the work for which this permit is issued. My workers' compensation insurance carrier and policy number are: Carrier: STATE COMPENSATION INSURANCE FUND Policy Number: 9087965 I certify that in the performance of the work for which this permit is issued, I shall not employ any person in any manner so as to become subject to the workers' compensation laws of California, and agree that, if I should become subject to the workers' compensation provisions of Section 3700 of the Labor Code, I shall forthwith comply with those provisloos. Date:Applican WARNING: FAILURE TO SECURE WORKERS' COMPENSATION COVERAGE IS UNLAWFUL, AND SHALL SUBJECT AN EMPLOYER TO CRIMINAL PENALTIES AND CIVIL FINES UP TO ONE HUNDRED THOUSAND DOLLARS ($100,000). IN ADDITION TO THE COST OF COMPENSATION, DAMAGES AS PROVIDED FOR IN SECTION 3706 OF THE LABOR CODE, INTEREST, AND ATTORNEY'S FEES. APPLICANT ACKNOWLEDGEMENT IMPORTANT: Application is hereby made to the Building Official for a permit subject to the conditions and restrictions set forth on this application. 1. Each person upon whose behalf this application is made, each person at whose request and for whose benefit work is performed under or pursuant to any permit issued as a result of this application , the owner, and the applicant, each agrees to, and shall defend, indemnify and hold harmless the City of La Quinta, its officers, agents, and employees for any act or omission related to the work being performed under or following issuance of this permit. 2. Any permit issued as a result of this application becomes null and void if work is not commenced within 180 days from date of issuance of such permit, or cessation of work for 180 days will subject permit to cancellation. I certify that I have read this application and state that the above information is correct. I agree to comply with all city and county ordinances and state laws relating to building construction, and hereby authorize representatives of this city to enter upon the above -mentioned property for inspection purposes. Date: ignature (Applicant orAgen Date: 1/24/2019 Application Number: BCOM2018-0049 Property Address: 50855 WASHINGTON ST STE 2H APN: 770020017 Application Description: FRENCH ROTISSERIE / KITCHEN FIRE DAMAGE REMODEL Property Zoning: Application Valuation: $5,000.00 Applicant: SIPOVAC CONSTRUCTION INC 72651 THEODORA LANE PALM DESERT, CA 92260 Owner: LQ INV 17165 NEWHOPE ST FOUNTAIN VALLEY, CA 92253 Contractor: SIPOVAC CONSTRUCTION INC 72651 THEODORA LANE PALM DESERT, CA 92260 (760)567-2347 Llc. No.: 581636 Detail: FRENCH ROTISSERIE / REPAIR DUE TO FIRE DAMAGE. REPLACE TYPE I HOOD, GREASE DUCT, EXHAUST FAN, MAKEUP AIR UNIT, LIGHT FIXTURES, GAS LINE AND T-BAR CEILING AND REPAIR ROOF PENETRATION BY FIRE SUPPRESSION PERSONNEL. 2016 BUILDING CODES. FINANCIAL INFORMATION DESCRIPTION ACCOUNT QTY AMOUNT 101-0000-42600 ($11.54) DESCRIPTION ACCOUNT CITY AMOUNT 101-0000-42600 ($26.68) DESCRIPTION ACCOUNT CITY AMOUNT DEVICES, FIRST 20 101-0000-42403 0 $11.54 DESCRIPTION ACCOUNT QTY AMOUNT DEVICES, FIRST 20 101-0000-42403 0 $15.14 DESCRIPTION ACCOUNT CITY AMOUNT DEVICES, FIRST 20 PC 101-0000-42600 0 $26.68 Total Paid for ELECTRICAL: $15.14 DESCRIPTION ACCOUNT CITY AMOUNT FIRE COMMERCIALTI PC 101-0000-42420 0 $240.00 Total Paid for FIRE FEES: $240.00 DESCRIPTION ACCOUNT QTY AMOUNT 101-0000-42600 ($13.34) DESCRIPTION ACCOUNT QTY AMOUNT 101-0000-42600 ($5.34) DESCRIPTION ACCOUNT CITY AMOUNT 101-0000-42600 ($13.34) DESCRIPTION ACCOUNT QTY AMOUNT 101-0000-42600 ($13.34) DESCRIPTION ACCOUNT CITY AMOUNT EVAPORATIVE COOLER 101-0000-42402 0 $13.34 DESCRIPTION ACCOUNT QTY AMOUNT EVAPORATIVE COOLER PC 101-0000-42600 0 $13.34 DESCRIPTION ACCOUNT QTY AMOUNT EXHAUST HOOD 101-0000-42402 0 $13.34 DESCRIPTION ACCOUNT CITY AMOUNT EXHAUST HOOD PC 101-0000-42600 0 $5.34 Total Paid for MECHANICAL: $0.00 DESCRIPTION ACCOUNT CITY AMOUNT PLAN CHECK DEPOSIT - ADDITION/REMODEL 101-0000-42600 1 $125.00 Total Paid for PLAN CHECK DEPOSIT - ADDITION/REMODEL: $125.00 DESCRIPTION ACCOUNT CITY AMOUNT 101-0000-42600 ($13.34) DESCRIPTION ACCOUNT QTY AMOUNT 101-0000-42600 ($26.68) DESCRIPTION ACCOUNT CITY AMOUNT GAS SYSTEM, 1-4 OUTLETS 101-0000-42401 0 $13.34 DESCRIPTION ACCOUNT CITY AMOUNT GAS SYSTEM, 1-4 OUTLETS PC 101-0000-42600 0 $26.68 Total Paid for PLUMBING FEES: $0.00 DESCRIPTION ACCOUNT CITY AMOUNT RECORDS MANAGEMENT FEE - MAJOR 101-0000-42416 0 $21.00 Total Paid for RECORDS MANAGEMENT FEE - MAJOR: $21.00 DESCRIPTION ACCOUNT CITY AMOUNT 101-0000-42600 ($1.40) DESCRIPTION ACCOUNT CITY AMOUNT SMI - COMMERCIAL 101-0000-20308 0 $1.40 Total Paid for STRONG MOTION INSTRUMENTATION SMI: $0.00 DESCRIPTION ACCOUNT CITY AMOUNT TECHNOLOGY ENHANCEMENT FEE 502-0000-43611 0 $5.00 Total Paid for TECHNOLOGY ENHANCEMENT FEE: $5.00 zaO"i�( PERMIT# � PLAN LOCATION: Project Address:SS WF1SI�JC�T61J STE S� Zhu- Project Description: Pool, Remodel, Add't, Elect, Plumb, Mech APN #: C` UHA..• Applicant Name: Address:s �M1 City, ST, Zip: ry _ Telephone: Email: Valuation of Project $ Contractor Name: �-� �, New SFD Construction: Address:C �-� j ! �_ Conditioned Space SF City, St, Zip r"sTelephone: Garage SF ZO s-/ 17 Patio/Porch SF Email: ��1rC� Fire Sprinklers SF State Lic: K ity Bus Lie: Arch/Eng Name: Construction Type: Occupancy: Address: Grading: City, St, Zip Telephone: Bedrooms: Stories: # Units: Email: State Lic: City Bus Lic: Property Owner's Name:UL �l p�, ` New Commercial / Tenant Improvements: Address: S s S mr� J� 5�,�� t+ Total Building SF City, ST, Zip G� v `i ' 7 2 S Construction Type: Occupancy: Telephone: v 7 Email: ��sS` OJ&,'01 78495 CALLS TAMPIcn LA QUINTA, CA 92253 760-777-7000 RA Structural Attn: Reza Asgharpour 77570 Springfield Lane Palm Desert, CA 92211 Re: Work Verification S 3. PUVAC CONSTRUCTION INNOVATION This letter is to verify that the grease duct and the hood combined total weight is 743 pounds for the French Rotissere cafe located at 50855 Washington Street La Quinta, CA 92253. Thank you, Bob Sipovac Owner Sipovac Construction Inc. Lic. 581636 72651 Theodora Lane Palm Desert, Ca 92260 (760) 567-2347 72651 Theodora Ln. Palm Desert, Ca 92260 (760) 360-9700 Fax: (760)406-9734 License# 581636 DIVISION: 07 00 00—THERMAL AND MOISTURE PROTECTION SECTION: 07 8133—MINERAL-FIBER FIR REPORT HOLDER: 3M FIRE PROTECTION PRODU 3M CENTER, BUILDING 223-2N-20 ST. PAUL, MINNESOTA 55144-1000 EVALUATION SUBJECT: iNSPE�na 3M FIRE BARRIER DUCT WRAP 615+ BLANKET FOR GREASE DUCT ENCLOSURE ASSEMBLIES RFC:EIVEG ICC ICG ICCF� � ..r t,� OP QUIn�Ta, E�CQNIMUNTi DEVELOPMENT C� PMG LISTED Look for the trusted marks of Conformity! "2014 Recipient of Prestigious Western States Seismic Policy Council (WSSPQ Award in Excellence" ICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed as an endorsement of the subject of the report or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as to any finding or other matter in this report, or as to any product covered by the report. A Subsidiary of canf coufl i xC A" cavrs t PROOUCf C91IIFM'ATION AocNd�CCl1 ��w IMES Evaluation Report ESR-1255 Reissued May 2016 This report is subject to renewal May 2018. wwwAcc-es.orcl 1 (800) 423-6587 1 (662) 699-0543 A Subsidiary of the International Code Council® DIVISION: 07 00 00—THERMAL AND MOISTURE PROTECTION Section: 07 81 33—Mineral-Fiber Fireproofing REPORT HOLDER: 3M FIRE PROTECTION PRODUCTS 3M CENTER, BUILDING 223-2N-20 ST. PAUL, MINNESOTA 55144-1000 (651) 733-0973 www-3m.comtflm EVALUATION SUBJECT: 3M FIRE BARRIER DUCT WRAP 615+ BLANKET FOR GREASE DUCT ENCLOSURE ASSEMBLIES 1.0 EVALUATION SCOPE Compliance with the following codes: ■ 2012 and 2009 International Building Codee (IBC) ■ 2012 and 2009 Intemational Mechanical Code® (IMC) ■ 2012 and 2009 IAPMO Uniform Mechanical Code (UMC) ■ Other Codes (see Section 8.0) Properties evaluated: ■ Durability ■ Fire resistance ■ Noncombustibility s Surface burning characteristics 2.0 USES The 3M Fire Barrier Duct Wrap 615+ is a flexible blanket used to construct zero -clearance, fire -resistance -rated grease duct enclosure assemblies serving Type I kitchen hoods. The duct wrap material complies with 2012 IMC Section 506.3.11.2 (2009 IMC Section 506.3.10.2) and 2012 IAPMO UMC Sections 507.2.5 and 507.2.6 (2009 IAPMO UMC Sections 507.2.6 and 510.7.3.1), and is an alternative to the one- and two-hour fire -resistance -rated enclosure requirements of 2012 IBC Section 713.4 (2009 IBC Section 708.4) and 2012 IAPMO UMC Section 510.7 (2009 IAPMO UMC Section 510.7.1), when installed in accordance with Section 4.0. 3.0 DESCRIPTION 3.1 Materials: 3.1.1 3M Fire Barrier Duct Wrap 615+ Blanket: The blanket consists of a monolithic layer of proprietary soluble, vitreous alkaline earth oxide (calcium- silicone-, magnesium -oxide) fiber material encapsulated in a foil scrim, having a total nominal thickness of 1112 inches. It is packaged in rolls 25 feet (7.6 m) long and either 24 inches (610 mm) or 48 inches (1219 mm) wide. The blankets have a nominal density of 6 pcf and have a flame -spread index of 25 or less and a smoke -developed index of 50 or less when tested in accordance with ASTM E84_ The 615+ - blanket is classified as noncombustible when tested in accordance with ASTM E136. 3.1.2 Banding Material: Banding material must the minimum 1/2-inch-wide (12.7 mm),, 0.015-inch-thick (3.8 mm) stainless steel or carbon steel strap. Tools used for banding are a hand tensioner and a clip seal crimping tool. 3.1.3 Duct System: The duct must comply with Section 506.3 of the IMC or Sections 510.1, 510.4 or 510.5 of the UMC, as applicable. Under the IMC, grease ducts serving Type I hoods must be constructed either of minimum 0.0575-inch-thick (1.46 mm) (No. 16 gage) steel or of stainless steel at least 0.045 inch (1.14 mm) thick. Under the UMC, grease ducts serving Type I hoods must be constructed either of minimum 0.054-inch-thick (1.37 mm) (No. 16 MSG) steel or of stainless steel not less than 0.043 inch (1.09 mm) (No. 18 MSG) thick. Joints and seams of grease ducts must comply with Section 506.3.2 of the IMC, or Section 510.5.2 of the UMC. Duct supports must comply with Section 506.3.3 of the IMC, or Sections 510.1.6 and 510.5.1 of the 2012 IAPMO UMC (2009 IAPMO UMC Sections 510.1.7 and 510.5.1), as applicable, and Section 4.2.3 of this report. Maximum duct size is 48 inches by 24 inches (1219 mm by 610 mm). 3.1.4 Sealants: 3M Fire Barrier 1000 N/S Silicone Sealant (Non -Slump) and 3M Fire Barrier 1003 S/L Silicone Sealant (Self -Leveling) are ready -to -use, one -component silicone elastomers used in through - penetration fire -stop assemblies described in Section 4.2.4. The sealants are packaged in cartridges and have a shelf life of 12 months from date of packaging when stored in a clean, dry area with temperatures between 40°F and 90°F (4.4°C and 32.21C). 3.1.5 3M Fire Barrier Grease Duct Access Door and DuctMate ULtimate Door: The rectangular prefabricated access doors are UL listed Hood and Duct Accessories. The access doors are provided in three sizes: 12 inches by 8 inches (305 mm by 203 mm), 14 inches by 10 inches (356 mm by 254 mm) and 22 inches by 22 inches (559 mm by 559 mm). The access door assembly consists of the 3M access door, four 1/4-inch-diameter (6.4 mm) threaded ICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor arc they to be rmtsirned as an endorsement ofthe subject of the report or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express in, wnphe.d, as to anv finding or other matter in this report- or as to anv nroduct covered by the renort- yntay - extension rods, three layers of the 615+ blanket, a No. 16 gage cover plate, and wing nuts and washers. 4.0 INSTALLATION 4.1 General: The Duct Wrap 615+ wrap materials are installed with zero clearance from the ducts, and may be installed with zero clearance from the insulating material to combustible construction. Grease ducts protected with Duct Wrap 615+ are permitted to penetrate nonfire-resistance-rated wall, floor -ceiling and roof -ceiling assemblies, provided the duct is protected from the point of penetration in accordance with this report. The systems are also permitted to penetrate fire -resistance -rated assemblies when the through -penetration is protected in accordance with Section 4.2.4 of this report. The systems comply with the requirements of Section 602.2.1 of the IMC, and Section 602.2 of the UMC for installation in plenums. 4.2 Two-hour Fire -resistance -rated Enclosure Assembly: 4.2.1 Enclosure Assembly: The duct must be installed in accordance with Section 506.3.8 of the IMC or Sections 510.1, 510.4 or 510.5 of the UMC, as applicable. Ducts must have a maximum 48-inch-by-24-inch (610 mm by 1219 mm) cross -sectional opening. A total of two layers of blanket material is installed around the grease duct, using one of the four overlap techniques illustrated in Figure 1. Adjacent blankets on the inside layer are installed with either tight butt -joints between blankets or 3-inch (76 mm) perimeter and longitudinal overlaps. Edge joints of the second layer must be offset 101/2 inches (267 mm) from those of the first layer. The second layer of blanket material must have minimum 3-inch (76 mm) perimeter and longitudinal overlaps. Before the insulation is applied on ducts of 24 inches and larger, 7-inch-long (178 mm), No. 12 gage, copper -coated, mild steel impaling pins must be welded to the duct on the underside of horizontal assemblies and vertical assemblies spaced as illustrated in Figure 1 B. Galvanized, mild steel speed washers must be placed over each impaling pin to secure the blanket. Steel banding straps must be placed circumferentially, 1" 12 inches (38 mm) from the edge of the blanket and at 10'/2 inches (267 mm) on center. Material must not be installed that has been abused or damaged, e.g., stepped on, unintentionally cut or ripped. The tension in the banding straps must be sufficient to firmly retain the blanket materials, but not to unduly compress the blanket, and must not be so great as to cause any cutting or damage or compression to the blanket material. Seven- inch -long (178 mm), No. 12 gage, copper -coated, mild steel impaling pins, welded to the duct as shown in Figure 1 B, can be used as an alternative to steel banding straps on any size duct. 4.2.2 Grease Duct Access Doors: 4.2.2.1 General: Grease duct access doors must comply with Section 506.3. 8 of the IMC, and Section 510.3 of the UMC, as applicable. 4.2.2.2 Prefabricated Access Doors: The 3M Fire Barrier Grease Duct Access Door Assembly or Ductmate Ultimate Doors are installed as illustrated in Figure 3. Three layers of the 615+ blanket must be installed over the access door such that each layer overlaps the preceding layer by 1 inch (25 mm) on all four sides. Edges of the outer layer of insulation blanket must be sealed with aluminum foil tape. A No. 16 gage steel plate the same size as the outer layer of insulation blanket must be 4.2.2.3 Field -fabricated Access Doors: The access doors must be protected with three layers of 3M Fire Barrier Duct Wrap 615+ blanket material as illustrated in Figures 2 and 3. The first layer of blanket is cut the same size as the door, and the subsequent layers must overlap the previous layer by 1 inch (25.4 mm). Access door labels must be applied to all access doors. 4.2.3 Duct Support: Horizontal duct assemblies with maximum cross -sectional openings of 24 inches by 24 inches (610 mm by 610 mm) must be supported with minimum /e-inch-diameter (9.5 mm), all -thread steel rod and 2-inch-by-2-inch-by-'/s•inch (51 mm by 51 mm by 3.2 mm) steel angle, spaced a maximum of 60 inches (1524 mm) on center. A minimum clearance of 0 inch and a maximum clearance of 6 inches (152 mm) is required between the vertical edge of the blanket material surrounding the duct and the steel rod. Horizontal duct assemblies with maximum dimensions of 24 inches by 48 inches (610 mm by 1219 mm) must be supported with minimum '/x inch -diameter (12.7 mm), all -thread steel rod and 2-inch-by-2-inch-by I/4-inch (51 mm by 51 mm by 6.4 mm) steel angle spaced a maximum of 60 inches (1524 mm) on center. A minimum clearance of 0 inch (0 mm) and a maximum clearance of 6 inches (152 mm) is required between the vertical edge of the blanket material surrounding the duct and the steel rod. Vertical assemblies must be supported as shown in Figure 4. Vertical ducts must be supported at every floor line on the top of the slab. 4.2.4 Through -penetration Fire -stop Assemblies: See Table 1 and Figures 4 and 5 for descriptions of various through -penetration firestop assemblies that are used with the 3M Fire Barrier Duct Wrap 615+ system. The forming material placed in the annular space must be compressed to fill the space. The forming material must be recessed the appropriate depth (identified as Sealant Depth in Table 1) for application of the sealant. The sealant must be flush with the wall or floor surface. On floors, the sealant must be overlapped onto the floor approximately 1 inch �25.4 mm) and onto the insulated duct approximately /4 inch (6.4 mm). 5.0 CONDITIONS OF USE The 3M Fire Barrier Duct Wrap 615+ grease duct enclosure assembly described in this report complies with, or is a suitable alternative to what is specified in, those codes listed in Section 1.0 of this report, subject to the following conditions: 5.1 The enclosure systems must be constructed and installed in accordance with this report. In the event of a conflict between this report and the manufacture's instructions, this report governs. 5.2 The blanket materials are manufactured for 3M in Coahuila, Mexico, under a quality control program with inspections by ICC-ES. 6.0 EVIDENCE SUBMITTED Data in accordance with ASTM E2336 and the ICC-ES Acceptance Criteria for Field -applied Grease Duct Enclosure Assemblies (AC101.1), dated December 2012 (editorially revised November 2013). 7.0 IDENTIFICATION The 3M Fire Barrier Duct Wrap 615+ blanket material must bear a label indicating the product name, the 3M Fire Protection Products name and address, clearances in accordance with the applicable code, and the evaluation Enclosure, Do Not Remove" must be printed on the blankets at maximum 24-inch (610 mm) intervals. The 3M Fire Barrier Grease Duct Access Doors are identified by a label bearing the 3M Company name and address, and the product name. The Ductmate Ultimate Doors are identified by a label bearing the Ductmate Industries, Inc.'s name and address, and the product name. Sealants must be identified by the 3M company name and address, and the product name. 8.0 OTHER CODES: In addition to the codes referenced in Section 1.0, the products described in this report were evaluated for compliance with the requirements of the following codes: ■ 2006 International Building Code® (2006 IBC) e 2006 International Mechanical Code® (2006 IMC) * 2006 IAPMO Uniform Mechanical Code (2006 UMC) ■ 2003 International Building Code® (2003 IBC) ■ 2003 International Mechanical Code° (2003 IMC) ■ 2003 IAPMO Uniform Mechanical Code (2003 UMC) The products comply with the above -mentioned codes as described in Sections 2.0 through 7.0 of this report, except the applicable code sections are as follows for the report sections cited: Section 2.0: — Grease duct enclosures: 0 2006 and 2003 IMC Section 506.3.10 — Shaft enclosures: 0 2006 and 2003 IBC Section 707.4 0 2006 and 2003 UMC Section 510.7.1 • Section 3.2 — Joints and seams of grease ducts: 0 2006 and 2003 IMC Section 506.3.2 0 2006 and 2003 UMC Section 510.5.2 — Duct supports: 0 2006 and 2003 IMC Section 506.3.3 0 2006 and 2003 UMC Sections 510.1.7 and 510.5.1 • Section 4. 1: — 2006 and 2003 IMC Section 602.2.1 — 2006 and 2003 UMC Section 602.2 • Section 42.2.1: — 2006 IMC Section 506.3.8 — 2003 IMC Sections 506.3.9 and 506.3.11 — 2006 and 2003 UMC Section 510.3 TABLE 1—THROUGH-PENETRATION FIRESTOP ASSEMBLIES' MAXIMUM DUCT WALL, FLOOR OR ANNULAR SPACE PENETRATION FIRESTOP FIRE -RESISTANCE SIZE CEILING (inches) RATING (inches by inches) CONSTRUCTION (hours) Min. Max. Forming Materials Sealant Depth F-Rating T-Rating (inches) No. 25 gage steel Unfaced 3M Duct 24 x 30, wrapped with 3M Duct Wrap tuds with one layer of s6 6/ Wrap or min. 4 pcf ele, /„-inch gypsum board 3'/2 mineral wool both sides 1 NA through -penetration on both sides compressed 25 percent 24 x 30, wrapped with No 25 gage steel Unfaced 3M Duct Wrap or min. 4 pcf 3M Duct Wrap studs with two layers Is 1 31/2 mineral wool s/8, both sides 2 NA through -penetration of -inch gypsum board on both sides compressed to fill the annular space 2-by-10 wood joists, Unfaced 3M Duct 24 x 30, wrapped with with inch gypsum c n the bottom board o Wrap or min. 4 pcf 3M Dud Wrap side and 1 , 2 /2 mineral wool s /4, top surface 1 1 through -penetration plywood on the top compressed 25 side percent Unfaced 3M Duct 24 x 30, wrapped with , 4 /oncr reinforced Wrap or min. 4 pcf 3M Dud Wrap c concrete slab 11/4 21/2 mineral wool 7/16, top surface 2 2 through -penetration compressed to fill the annular space Unfaced 3M Duct 24 x 30, bare dud !z-inch reinforced Wrap or min. 4 pcf4 3/6, through -penetration concrete slab 1 2 mineral wool top surface 2 2 compressed 25 percent Unfaced 3M Duct 24 x 48, wrapped with 4 ,/2-inch reinforced Wrap or min. 4 pcf 3M Duct Wrap concrete slab 1 41/2 mineral wool 1/4, top surface 2 2 through -penetration compressed 56 percent For SI: 1 inch = 25.4 mm. FIGURE 1A 3M FIRE BARRIER DUCT WRAP 615+ FIGURE 1B 3M FIRE BARRIER DUCT WRAP COMMERCIAL KITCHEN GREASE DUCT SYSTEMS SYSTEMS 1 OR 2 HOUR SHAFT ALTERNATIVE ZERO CLEARANCE TO COMBUSTIBLES COMMERCIAL KITCHEN GREASE DUCT SSY TELESCOPING TECHNIQUE W/BANDING ONLY 1 OR 2 HOUR SHAFT ALTERNATIVE ZERO CLEARANCE TO COMBUSTIBLES FOR DUCTS 24- (60.9 CM) OR LESS TELESCOPING TECHNIQUE WNVELD PINS ONLY r 4 w. 5 ` 6 2 FIGURE 1C TELESCOPING OVERLAP WRAP OPTION FIGURE 1D BUTT JOINT WITH COLLAR OPTION CROSS SECTIONAL VIEW CROSS SECTIONAL VIEW 3 3 ;7Rmrn] 3" [76rx• '�.-l-.. .. 2 T-iHinnli—I I� _ 4 2 A I rir•.•r 1 - 1 A --- FIGURE 1 E CHECKERBOARD OVERLAP OPTION CROSS SECTIONAL VIEW FIGURE 1 F BUTT/OVERLAP OPTION CROSS SECTIONAL VIEW 6 .0 of •ia'4 L. Fot L�W i s 64-' C..,n'- Tu r-- M_., 1 N.t w !�n p 11 Ai7i By 4-fit, of mft FIGURE 2-3M FIRE BARRIER DUCT WRAP 615+ COMMERCIAL KITCHEN GREASE DUCT SYSTEMS, I- OR 2-HOUR, ACCESS DOOR SYSTEM 3" (76 mm) MIN. TYP. 7-7 D It > CIO 2 &LLD FIGURE 3-3M FIRE BARRIER OR DUCTMATE ULTIMATE GREASE ACCESS DOOR 1. �'rtst -Ytl 2. 'Secord Layer 3M -r;rc, Bcrr,:,cr D,L-,t Wrap 613+ 3. Mecham7ca:: I usteners cra 'Washers 4 FIL.Ct 5. Rated 6. IlrestonDrg System Support Channel System :ntcqr'.ty 's by qua:ity of instaliction. FIGURE 4-3M FIRE BARRIER DUCT WRAP 615+ COMMERCIAL KITCHEN GREASE DUCT SYSTEMS, I- OR 2-HOUR, VERTICAL SUPPORT FIGURE 5A NNFIRE BARRIER DUCT WRAP O15+ COMMERCIAL KITCHEN GREASE DUCT SYSTEMS 1OR2HOUR THROUGH PENETRATION SYSTEMS 4-1/2INCH <11.4cm>CONCRETE FLOOR ORWALL " | � /76 rnrn\ l - -^� '���---------- ^..` ^ ^~ .~~` =�� °m �~Ai", *~." '. ~., ~°= ° ~* FIGUFE5B 3NFIRE BARRIER DUCT WRAP O1S+ COMMERCIAL KITCHEN GREASE DUCT SYSTEMS 1OR2HOUR THROUGH PENETRATION SYSTEMS FIRE -RATED GYPSUM WALLBOARD FKGUnE5C F|GVRE5D 3MF|RE BARRIER DUCT WRAP 615+ 3MFIRE BARRIER DUCT WRAP015+ COMMERCIAL KITCHEN GREASE DUCT SYSTEMS COMMERCIAL KITCHEN GREASE DUCT SYSTEMS 1QR2 HOUR THROUGH PENETRATION SYSTEMS 1HOUR THROUGH PENETRATION SYSTEMS 4'1CzINCH (11.4cm)CONCRETE FLOOR ORWALL FIRE RATED WOOD/GYPSUM -FLOOR/CEILING ASSEMBLY (: '' v ~° .1 / ~ 8 mm) ,'3' (76 mm) \ ` -