Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
BRES2019-0106
78-495 CALLE TAMPICO LA QUINTA, CALIFORNIA 92253 Permit Type/Subtype: Application Number: Property Address: APN: Application Description: Property Zoning: Application Valuation: c&t,, 4 4v QumAj DESIGN & DEVELOPMENT DEPARTMENT BUILDING PERMIT BUILDING RESIDENTIAL/REMODEL BRES2019-0106 78371 TALKING ROCK TURN 770300042 POWELL / REMODEL AT COURTYARD AND REAR OF DWELLING $125,000.00 Applicant: FEDDERLY & ASSOCIATES 78206 VARNER ROAD STE D #248 PALM DESERT, CA 92211 Q n JUN 1 ." 2019 Gi1Y GF L�,; LICENSED CONTRACTOR'S DECLARATION I hereby affirm under penalty of perjury that I am licensed under provisions of Chapter 9 (commencing with Section 70001 of Division 3 of the Business and Professions Code, and my License is in full force and effect. License Class: B License No.: 744091 Date: a Contractor: OWNER -BUILDER DECLARATION hereby affirm under penalty of perjury that I am exempt from the Contractor's State License Law for the following reason (Sec. 7031.5, Business and Professions Code: Any city or county that requires a permit to construct, alter, improve, demolish, or repair any structure, prior to its issuance, also requires the applicant for the permit to file a signed statement that he or she is licensed pursuant to the provisions of the Contractor's State License Law (Chapter 9 (commencing with Section 7000) of Division 3 of the Business and Professions Code) or that he or she is exempt therefrom and the basis for the alleged exemption. Any violation of Section 7031.5 by any applicant for a permit subjects the applicant to a civil penalty of not more than five hundred dollars ($500).: (_) I, as owner of the property, or my employees with wages as their sole compensation, will do the work, and the structure is not intended or offered for sale. (Sec. 7044, Business and Professions Code: The Contractors' State License Law does not apply to an owner of property who builds or improves thereon, and who does the work himself or herself through his or her own employees, provided that the improvements are not intended or offered for sale. If, however, the building or improvement is sold within one year of completion, the owner -builder will have the burden of proving that he or she did not build or improve for the purpose of sale.). (_) I, as owner of the property, am exclusively contracting with licensed contractors to construct the project. (Sec. 7044, Business and Professions Code: The Contractors' State License Law does not apply to an owner of property who builds or improves thereon, and who contracts for the projects with a contractor(s) licensed pursuant to the Contractors' State License Law.). (_) I am exempt under Sec. B.&P.C. for this reason Owner: CONSTRUCTION LENDING AGENCY I hereby affirm under penalty of perjury that there is a construction lending agency for the performance of the work for which this permit is issued (Sec. 3097, Civ. C.). Lender's Name: Lender's Add VOICE (760) 777-7125 FAX (760) 777-7011 INSPECTIONS (760) 777-7153 Date: 6/12/2019 Owner: STEPHEN AND DARLA POWELL 78371 TALKING ROCK TURN LA QUINTA, CA 92253 Contractor: SUN VISTA DEVELOPMENT CORPORATION P0BOX 1144 LA QUINTA, CA 92247 (760)771-4722 Llc. No.: 744091 WORKER'S COMPENSATION DECLARATION I hereby affirm under penalty of perjury one of the following declarations: I have and will maintain a certificate of consent to self -insure for workers' compensation, as provided for by Section 3700 of the Labor Code, for the performance of th ❑ far which this permit is issued. ave and will maintain workers' compensation insurance, as required by Section 3700 of the Labor Code, for the performance of the work for which this permit is issued. My workers' compensation insurance carrier and policy number are: Carrier: STATE COMPENSATION INSURANCE FUND Policy Number: 637385 I certify that in the performance of the work for which this permit is issued, I shall not employ any person in any manner so as to become subject to the workers' compensation laws of California, and agree that, if I should become subject to the workers' compensation provisions of Section 3700 of the Labor Code, I shall forthwith comply with those provisions. Date. Z Applicant: WARNING: FAILURE TO SECURE WORKERS' COMPENSATION COVERAGE IS UNLAWFUL, AND SHALL SUBJECT AN EMPLOYER TO CRIMINAL PENALTIES AND CIVIL FINES UP TO ONE HUNDRED THOUSAND DOLLARS ($100,000). IN ADDITION TO THE COST OF COMPENSATION, DAMAGES AS PROVIDED FOR IN SECTION 3706 OF THE LABOR CODE, INTEREST, AND ATTORNEY'S FEES. APPLICANT ACKNOWLEDGEMENT IMPORTANT: Application is hereby made to the Building Official for a permit subject to the conditions and restrictions set forth on this application. 1. Each person upon whose behalfthis application is made, each person at whose request and for whose benefit work is performed under or pursuant to any permit issued as a result ofthis application , the owner, and the applicant, each agrees to, and shall defend, indemnify and hold harmless the City of La Quinta, its officers, agents, and employees for any act or omission related to the work being performed under or following issuance of this permit. 2. Any permit issued as a result of this application becomes null and void if work is not commenced within 180 days from date of issuance of such permit, or cessation of work for 180 days will subject permit to cancellation. I certify that I have read this application and state that the above information is correct. I agree to comply with all city and county ordinances and state laws relating to building construction, and hereby authorize representatives of this city to enter upon the above - mentioned property for inspection purposes. Date: �Z Signature (Applicant or Agent): Date: 6/12/2019 Application Number: BRES2019-0106 Property Address: 78371 TALKING ROCK TURN APN: 770300042 Application Description: POWELL / REMODEL AT COURTYARD AND REAR OF DWELLING Property Zoning: Application Valuation: $125,000.00 Applicant: FEDDERLY & ASSOCIATES 78206 VAR NER ROAD STE D #248 PALM DESERT, CA 92211 Owner: STEPHEN AND DARLA POWELL 78371 TALKING ROCK TURN LA QUINTA, CA 92253 Contractor: SUN VISTA DEVELOPMENT CORPORATION P0BOX 1144 LA QUINTA, CA 92247 (760)771-4722 Llc. No.: 744091 Detail: POWELL / REMODEL AT COURTYARD AND REAR OF HOME. REPLACE DOORS AND WINDOWS, CONSTRUCT NEW FIREPLACE, REDESIGN REAR COVERED PATIO AREA. DOES NOT INCLUDE CONSTRUCTION OF POOL OR EXTERIOR FIRE PITS. 2016 CALIFORNIA BUILDING CODES. DESCRIPTION ACCOUNT CITY AMOUNT BSAS SB1473 FEE 101-0000-20306 0 $5.00 Total Paid for BUILDING STANDARDS ADMINISTRATION BSA: $5.00 DESCRIPTION ACCOUNT CITY AMOUNT RESIDENTIAL, EA ADDITION 1,000SF 101-0000-42403 0 $13.61 DESCRIPTION ACCOUNT CITY AMOUNT RESIDENTIAL, EA ADDITION 1,000SF, PC 101-0000-42600 0 $5.60 DESCRIPTION ACCOUNT CITY AMOUNT RESIDENTIAL, FIRST 1,000SF 101-0000-42403 0 $160.10 DESCRIPTION ACCOUNT CITY AMOUNT RESIDENTIAL, FIRST 1,000SF, PC 101-0000-42600 0 $52.83 Total Paid for ELECTRICAL - NEW CONSTRUCTION: $232.14 DESCRIPTION ACCOUNT CITY AMOUNT PLAN CHECK DEPOSIT - ADDITION/REMODEL 101-0000-42600 1 $125.00 Total Paid for PLAN CHECK DEPOSIT - ADDITION/REMODEL: $125.00 DESCRIPTION ACCOUNT CITY AMOUNT 101-0000-42600 ($125.00) DESCRIPTION ACCOUNT CITY AMOUNT REMODEL, EA ADDITIONAL 500 SF 101-0000-42400 0 $72.03 DESCRIPTION ACCOUNT CITY AMOUNT REMODEL, EA ADDITIONAL 500 SF PC 101-0000-42600 0 $57.63 DESCRIPTION ACCOUNT CITY AMOUNT REMODEL, FIRST 100 SF 101-0000-42400 0 $54.43 DESCRIPTION ACCOUNT CITY AMOUNT REMODEL, FIRST 500 SF PC 101-0000-42600 0 $125.00 DESCRIPTION ACCOUNT CITY AMOUNT REMODEL, FIRST 500 SF PC 101-0006--42600 0 $23.89 Total Paid for REMODEL: $207.98 DESCRIPTION ACCOUNT CITY AMOUNT SMI - RESIDENTIAL 101-0000-20308 0 $16.25 Total Paid for STRONG MOTION INSTRUMENTATION SMI: $16.25 DESCRIPTION ACCOUNT CITY AMOUNT TECHNOLOGY ENHANCEMENT FEE 502-0000-43611 0 $5.00 Total Paid for TECHNOLOGY ENHANCEMENT FEE: $5.00 -- GEIM nff/e DESERT - PERMIT # PLAN LOCATION: Project Address:-7�- 31 1 TA I V4 n pot V- Turn Project Description: Pool, Remodel, Add't, Elect, Plumb, Mech APN #: I7 D- ,w 1/l+i, oor 12-Made4 ' Nto drl V ow a s (1 W ktb- Arc S i WAU W ,1 A '- r p ll ApplicantName: FtA(��1de,610yl,S Y1 aw aleIaA I Address: -NIMP Wrl6i( I2A -;k- D - 24 j J Mal d Do aBEO DQQ1 City, ST, Zip: pa( m beG6,e+ CA t,12211 + Ace f l e omves swiffgwsll Telephone: '� (Op' '(12j' �J20Jr & voriW � Un e recLa4I h OwftA*-S bk-fih to Email: N l C Cg ��dd� I �� Valuation of Project $ 125 00 D - Oa Contractor Name: Fea dL✓1 �SSUCleS New SFD Construction: Address: I g2C)(P V aqof RA D , Conditioned Space SF City, St, Zip PA I m W q,.)/+ , 6A g27-1( Garage SF Telephone: IUD - 113_ 6"6 Patio/Porch SF Email: N'l to le- G @ f ed d erg I . cpnq Fire Sprinklers SF State Lic: I Ulgft j City Bus Lic: 6i q-1 I Arch/Eng Name: Construction Type: V b Occupancy: ?) Address: Grading: City, St, Zip Telephone: Bedrooms: Stories: ( # Units: Email: State Lic: City Bus Lic: Property Owner's Name: �Ve Ao W&i I New Commercial / Tenant Improvements: Address: TA 114 n 'r Total Building SF City, ST, Zip A � n-� cps g2253 Construction Type: Occupancy: Telephone: Email: 78495 CALLE TAMPICO LA QU I NTA, CA 92253 760-777-7000 OFFICE USE ONLY # Submittal Req'd Req'd Plan Sets Structural Calcs Truss Calcs Title 24 Calcs Soils Report Grading Plan (PM10) Landscape Plan Subcontractor List Grant Deed HOA Approval School Fees Burrtec Debris Plan Planning approval Public Works approval Fire approval City Business License -cCORDING REQUESTED BY Lawyers Title - IE WHEN RECORDED MAIL THIS DOCUMENT AND TAX STATEMENTS TO: Stephen W. Powell, Trustee and Darla Jean Powell, Trustee r� APN: 770-300-042-3 Escrow No: PDL15897-LT139-CM Title No: 618640602 GRANT DEED THE UNDERSIGNE❑ GRANTOR(S) DECLARi=(S) DOCUMENTARY TRANSFER TAX IS $ -- ©- _oompttted-on-Wl ►ralu ornmy-ed -.-- -- - -- -_-- . ❑O City of La Quinta, AND RECEIVED MAY 21 1019 CTIY OF LA %INTA DESIGN AND DEVELOPMENT DEPARTMENT FOR A VALUABLE CONSIDERATION, receipt of which is',e,eby ackno-aiedged, Longwood Capital Management, LLC a Texas Limited Liabf.=ty Ccmpany ' LCM! hereby GRANT(S) to Stephen W. Pote'T 3 Dar'a �ea= �_�e=-. _=st_e_ �_ W. and Darla Je;;- Purac' l Trust aice' -��i _= --2 the following described real property in the City of La Quinta, Coe,-ry of n:.e-=:e; Sate cr CALIFORNIA: For legal description of the real property herein, see Exhibit A attached hereto and made a part hereof. Commonly known as: 78371 Talking Rock Turn , La Quinta, CA 92253 Dated: February 28, 2018 1gngwoo4 Capital Management, LLC a Texas Limited Liability Company (LCM) By: D. S t e?pli;en en t i e s `� { A notary public or other officer completing this certificate verifies only the identity of the individual who signed the { document to which this certificate is attacbed, and not the truthfulness, accuracy, or validity of that document. i STATE OF 49 LLEDRU?A- t ;Lca S - 4� ) -� SS. COUNTY OF On f" l C�~"C �i,. 1 before me, r appeared 3irvr z i c S a o-.t- ° I- ~ ,� : iyYrsr'l '-F;! " who proved to me on the basis of satisfactoryevidence) to be the person(s) whose name(s) is/are subscribed to the within instrument and acknowledged to me that he/she/they executed the same in his/her/their authorized capacity(ies), and that by his/her/their signature(s) on the instrument the person(s), or the entity upon behalf of which the person(s) acted, executed the instrument. I certify under PENALTY OF PERJURY under the laws of the State of-Gafff€ ,rnia•that the foregoing paragraph is true and correct. WITNESS my hand and official seal.`°pY'`` JANICE DEANS _ Notary ID # 12414779-8 ,, L r _ K C- My Commission Expires -�> ( n„��,n*° March 8, 2018 Signature ' l}u`C. - ;,✓ir>tL •1 r�2• � : �.t.-rU' i'l•'r•4 :�•-. _ '`C: , _• r�-MC � :-r�s' ��!�c.. � Exhibit A THE LAND REFERRED TO HEREIN IS S7UA =0 DESCRIBED AS FOLLOWS: LOT 59 OF TRACT NO. 28470-2. SHOWN BY MAP ON FILE IN B02 - --- --=- -- ---- = � _ - - COUNTY RECORDER OF S4-7--, CC_% ASSE5502.'S ��� __ ,_`•'EE=.----"=-----�-_ RECEIVED MAY 21 2019 Cif [ OF LA QUIWA DESIG4 AND DEVEtOPi V DEPART4 EV TRADITION" HOMFOWNEWS ASSOCIAI-ION May 10, 2019 RECEIVED MAY 21 2019 CITY OF LA QUINTA Mr. and Mrs_ Steve Powell 78371 Talking Rock Turn DESIGN AND DEVELOPMENT DEPARTMENT La Quinta, CA 92253 Re: Lot 59, Tr. 28470-2 at 78371 Talking Rock Turn Architectural, Site and Landscape Remodel — Construction Documents42 Dear Mr. and Mrs. Powell: This correspondence shall serve as notification from the Tradition Architectural Design Review Committee ("ADRC") that the revised construction remodel documents were reviewed at the May 2, 2019 meeting. The project was approved to start construction subject to the following comments being addressed: 1. The color and material samples must be provided prior to purchase and installation, including the paint color LRV. In addition, a large stone sample will be required as the specification is noted as "Modern Materials" which is typically a thin -cut, dry -stack stone product which does not match the hatching call -outs indicated on the elevations. 2. The exterior light fixture was approved, subject to the bulb wattage being provided prior to purchase and installation. 3. The raised wall at the back of the pool is indicated as 18" on the Construction Plan; however, detail D/L-5 shows the wall as 24". Please indicate the finish grade elevation to help clarify what surface the 18" height is being measured from for construction. 4. If your review fee has not been provided, please submit it to the Association immediately. Please contact Brook Marshall at 760-219-8057 or by email at DRCFacilitator@gmail.com with any questions, or to schedule a Pre -Construction Meeting prior to any demolition or construction starting in the field. Sincerely, MAAByTRADITIONARC/IJMTE&a— Title:CTURAL AND DESIGN REVIEW COMMITTEE : 4 i I-W Date: % l o it q cc: Lance Fedderly ADRC File Pursuant to Cal. Civil Code, any rejection by the ADRC may be appealed to the Board of Directors for the Association. If you wish to pursue an appeal, please contact the Association's property manager so that you may be put on the ned meeting age•ada. DESERT RESORT MANAGMENT POST OFFICE BOX 14387 . PALM DESERT, CALIFORNIA 92255-4387 42-635 MELANIE PLACE, SUITE 103 . PALM DESERT, CALIFORNIA 92211 TELEPHONE (760) 340-1161 . FAX (760) 346-9918 Authorization to Pull Construction Permit Stephen Powell 78-371 Talking Rock Turn La Quinta, CA 92253 June 11, 2019 City of La Quinta Design & Development Department 78-495 Calle Tampico La Quinta, CA 92253 To Whom It May Concern: I, Stephen Powell, trustee of the STEPHEN W. AND DARLA JEAN POWELL TRUST dated January 19, 2006, as amended, hereby authorize Bill Letty of Sun Vista Construction, LLC to pull the permit from The City of La Quinta Design & Development Department for our residence remodel at 78-371 Talking Rock Turn in La Quinta. Your attention and cooperation in this matter is greatly appreciated. Best Regards, 4,' - � �D Stephen Powell RECENF_LF: JUN 12 2019 CITY OF LA QUINTA DESIGN AND DEVELOPMENT DEPARTMENT May 6, 2019 To Whom It May Concern: We, Stephen W. Powell and Darla Jean Powell, Trustees of the Stephen W. and Darla Jean Powell Trust dated January 19, 2006 as amended, authorize the scope of work as submitted to the City of La Quinta by Fedderly Et Associates for the property at 78-371 Talking Rack Turn in La Quinta (APN:700-300-042-3). Thank you Stephen Powell Darla Jean Powell Step RECEIVED MAY 21 2019 CITY OF LA QUINTA DESIGN AND DEVELOPMENT DEPARTMEN71 I BUILDING ENERGY ANALYSIS REPORT I PROJECT: Powell Residence 78-371 Talking Rock Turn La Quinta, CA 92253 Project Designer: Fedderly & Associates 38-747 Nopales Road Palm Desert, CA 92211 (760) 773-5205 Report Prepared by: Jon d. Scott Scott Design and Title 24, Inc, 74818 Velie Way Suite 8 Palm Desert, CA 92260 (760) 200-4780 fWES2.01c) - o104, Job Number: Date: 5/20/2019 CITY OF LA QUINTA BUILDING DIVISION REVIEWED FOR CODE COMPLIANCE DATE flo tvM By The EnergyPro computer program has been used to perform the calculations summarized in this compliance report. This program has approval and is authorized by the California Energy Commission for use with both the Residential and Nonresidential 2016 Building Energy Efficiency Standards. This program developed by EnergySoft Software — www.energysoft.com. I TABLE OF CONTENTS I Cover Page 1 Table of Contents 2 Form CF-1 R-PRF-01-E Certificate of Compliance 3 Form RMS-1 Residential Measures Summary 10 Form MFA R Mandatory Measures Summary 11 HVAC System Heating and Cooling Loads Summary 15 Room Load Summary 16 Room Heating Peak Loads 17 Room Cooling Peak Loads 18 CERT( TE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE' HOD Project Name: Powell C is culation Date/Time: 09:56, Mon, May 20, 2019 Calculation Description: Title 24 Analysis Input File Name: Powell-Traditions-Fedderly-19.ribdl6x CIF jRF-01 Page 1 of 7 GENERAL INFORMATION 01 Project Name Powell 02 Calculation Description Title 24 Analysis 03 Project Location 78-371 Talking Rock Turn 04 City La Quinta 05 Standards Version Compliance 2017 06 Zip Code 92253 07 Compliance Manager Version BEMCmpMgr 2016.3.1 (1149) 08 Climate Zone CZ15 09 Software Version EnergyPro 7.2 10 Building Type Single Family 11 Front Orientation (deg/Cardinal) 160 12 Project Scope Addition and/or Alteration 13 Number of Dwelling Units 1 14 Total Cond. Floor Area (ft) 6432 15 Number of Zones 1 16 Slab Area (ft2) 6432 17 Number of Stories 1 18 Addition Cond. Floor Area (ft) 0 19 Natural Gas Available Yes 20 Addition Slab Area (ft) 0 21 Glazing Percentage (%) 24.0% COMPLIANCE RESULTS 01 Building Complies with Computer Performance 02 This building DOES NOT require HERS Verification ENERGY USE SUMMARY 04 05 06 07 08 Energy Use (kTDV/ft2-yr) Standard Design Proposed Design Compliance Margin Percent Improvement Space Heating 4.74 5.43 -0.69 -14.6% Space Cooling 201.11 186.58 14.53 7.2% IAQ Ventilation 0.00 0.00 0.00 0.0% Water Heating 5.82 5.82 0.00 0.0% Photovoltaic Offset -- 0.00 0.00 - Compliance Energy Total 211.67 197.83 13.84 6.5% REQUIRED SPECIAL FEATURES The following are features that must be installed as condition for meeting the modeled energy performance for this computer analysis. NO SPECIAL FEATURES REQUIRED Registration Number: Registration Date/Time: HERS Provider: CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version - CF1 R-06232018-1149 Report Generated at: 2019-05-20 09:57:05 CERT( ,TE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE iHOD Project Name: Powell Calculation Date/Time: 09:56, Mon, May 20, 2019 Calculation Description: Title 24 Analysis Input File Name: Powell-Traditions-Fedderly-19.ribdl6x CF "RF-01 Page 2 of 7 HERS FEATURE SUMMARY The following is a summary of the features that must be field -verified by a certified HERS Rater as a condition for meeting the modeled energy performance for this computer analysis. Additional detail is provided in the building components tables below. Building -level Verifications: --None— Cooling System Verifications: -- None -- HVAC Distribution System Verifications: -- None -- Domestic Hot Water System Verifications: --None -- BUILDING - FEATURES INFORMATION 01 02 03 04 05 06 07 Number of Dwelling Number of Ventilation Number of Water Project Name Conditioned Floor Area (ft) Units Number of Bedrooms Number of Zones Cooling Systems Heating Systems Powell 6432 1 3 1 0 1 ZONE INFORMATION 01 02 03 04 05 06 07 Zone Name Zone Type HVAC System Name Zone Floor Area (ft2) Avg. Ceiling Height Water Heating System 1 Water Heating System 2 residence Conditioned HVAC1 6432 12.3 DHW Sys 1 n/a OPAQUE SURFACES 01 02 03 04 05 06 07 08 09 10 11 Name Zone Construction Azimuth Orientation Gross Area (ft2) Window & Door Area (ft) Tilt (deg) Wall Exception Status Verified Existing Condition NE Wall residence R-13 Wall 250 Left 1026 184.04 90 n/a Existing No SE Wall residence R-13 Wall 340 Back 1149 689 90 n/a Existing No SW Wall residence R-13 Wall 70 Right 1026 328.6 90 n/a Existing No NW Wall residence R-13 Wall 160 Front 1149 340.8 90 n/a Existing No Interior Surface residence R-0 Interior Wall 365 0 n/a Existing No Roof residence Default 1978 to present.. 6432 n/a Existing No Registration Number: Registration Dateffime: HERS Provider: CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version - CF1 R-06232018-1149 Report Generated at: 2019-05-20 09:57:05 CERTt ,TE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE HOD Project Name: Powell Calculation Description: Title 24 Analysis Calculation Date/Time: 09:56, Mon, May 20, 2019 Input File Name: Powell-Traditions-Fedderly-19.ribd16x CF —)RF-01 Page 3 of 7 ATTIC 01 02 03 04 05 06 07 08 09 10 Name Construction Type Roof Rise Roof Reflectance Roof Emittance Radiant Barrier Cool Roof Status Verified Existing Condition Attic residence Attic Roofresidence Ventilated 1 0.1 0.85 No No Existing No Registration Number: Registration DatefFime: HERS Provider: CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version - CF1 R-06232018-1149 Report Generated at: 2019-05-20 09:57:05 CERTI,' ,TE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE Project'Name: Powell Calculation Description: Title 24 Analysis 'HOD Caiculation DatelTime: 09:56, Mon, May 20, 2019 Input File Name: Powell-Traditions-Fedderly-1 9.ribdl 6x CF IRF-01 Page 4 of 7 FENESTRATION / GLAZING 01 02 03 04 05 06 07 08 09 10 11 Name Surface (Orientation -Azimuth) Width (ft) Height (ft) Multiplier Area (ft) U-factor SHGC Exterior Shading Status Verified Existing Condition 5--1 NE Wall (Left-250) - 1 60.0 0.30 0.20 Insect Screen (default) New n/a EXISTING DR WNDW SLDR. 2 NE Wall (Left-250) - - 1 36.0 0.71 0.60 Insect Screen (default) Existing No EXISTING DR WNDW SLDR.-3 NE Wall (Left-250) -- 1 22.8 0.71 0.60 Insect Screen (default) Existing No EXISTING DR WNDW SLDR-4 NE Wall (Left-250) - - 1 11.0 0.71 0.60 Insect Screen (default) Existing No EXISTING DR WNDW SLDR-5 NE Wall (Left-250) -- 1 9.1 0.71 0.60 Insect Screen (default) Existing No EXISTING DR WNDW SLDR-6 NE Wall (Left-250) -- - 1 9.1 0.71 0.60 Insect Screen (default) Existing No b-7 NE Wall (Left-250) - 1 36.0 0.30 0.20 Insect Screen (default) New n/a EXISTING DR WNDW SLDR-8 SE Wall (Back-340) 1 18.0 0.71 0.60 Insect Screen (default) Existing No 3--9 SE Wall (Back-340) - 1 140.0 0.30 0.20 Insect Screen (default) New n/a 2--10 SE Wall (Back-340) 1 300.0 0.30 0.20 Insect Screen (default) New n/a 1-11 SE Wall (Back-340) - - 1 150.0 0.30 0.20 Insect Screen (default) New n/a EXISTING DR WNDW SLDR-12 SE Wall (Back-340) 1 12.0 0.71 0.60 Insect Screen (default) Existing No EXISTING DR WNDW SLDR-13 SE Wall (Back-340) -- 1 12.0 0.71 0.60 Insect Screen (default) Existing No EXISTING DR WNDW SLDR-14 SE Wall (Back-340) - -- 1 57.0 0.71 0.60 Insect Screen (default) Existing No EXISTING DR WNDW SLDR-15 SW Wall (Right-70) - - 1 84.0 0.71 0.60 Insect Screen (default) Existing No EXISTING DR WNDW SLDR-16 SW Wall (Right-70) - 1 49.0 0.71 0.60 Insect Screen (default) Existing No EXISTING DR WNDW SLDR-17 SW Wall (Right-70) -- - 1 35.0 0.71 0.60 Insect Screen (default) Existing No EXISTING DR WNDW SLDR-18 SW Wall (Right-70) - - 1 18.0 0.71 0.60 Insect Screen (default) Existing No EXISTING DR WNDW SLDR-19 SW Wall (Right-70) - - 1 11.0 0.71 0.60 Insect Screen (default) Existing No 4-20 SW Wall (Right-70) - - 1 50.0 0.30 0.20 Insect Screen (default) Altered n/a EXISTING DR WNDW SLDR-21 SW Wall (Right-70) - 1 15.8 0.71 0.60 Insect Screen (default) Existing No EXISTING DR WNDW SLDR-22 SW Wall (Right-70) - - 1 15.8 0.71 0.60 Insect Screen (default) Existing No 4-23 SW Wall (Right-70) - - 1 50.0 0.30 0.20 Insect Screen (default) Altered n/a a-24 NW Wall (Front-160) - 1 60.0 0.30 0.20 Insect Screen (default) Altered n/a EXISTING DR WNDW SLDR-25 NW Wall (Front-160) - - 1 10.8 0.71 0.60 Insect Screen (default) Existing No 6-26 NW Wall (Front-160) -- - 1 72.0 0.30 0.20 Insect Screen (default) Altered n/a a-27 NW Wall (Front-160) 1 60.0 0.30 0.20 1 Insect Screen (default) Altered n/a EXISTING DR WNDW SLDR-28 NW Wall (Front-160) 1 57.0 0.71 1 0.60 1 Insect Screen (default) Existing No Registration Number: Registration Date/Time: HERS Provider: CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version - CF1 R-06232018-1149 Report Generated at: 2019-05-20 09:57:05 CERTI, %TE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE HOD Projeci-game: Powell Calculation Date/Time: 09:56, Mon, May 20, 2019 Calculation Description: Title 24 Analysis Input File Name: Powell-Traditions-Fedderly-19.ribd16x CF "RF-01 Page 5 of 7 EXISTING DR WNDW SLDR-29 NW Wall (Front-160) 1 24.0 0.71 0.60 Insect Screen (default) Existing No EXISTING DR WNDW SLDR-30 NW Wall (Front-160) 1 57.0 0.71 0.60 Insect Screen (default) Existing No OPAQUE SURFACE CONSTRUCTIONS 01 02 03 04 05 06 07 Total Cavity Winter Design Construction Name Surface Type Construction Type Framing R-value U-factor Assembly Layers • Cavity/Frame: no insul. /2x4 Top Chrd 2x4 Top Chord of Roof Truss @ 24 Roof Deck: Wood Siding/sheathing/decking Attic Roofresidence Attic Roofs Wood Framed Ceiling in. O.C. none 0.644 Roofing: Light Roof (Asphalt Shingle) • Inside Finish: Gypsum Board Ceilings (below Cavity/Frame: R-9.1 /2x4 Default 1978 to present.. attic) Wood Framed Ceiling 2x4 @ 16 in. O.C. R 11 0.083 Over Ceiling Joists: R-1.9 insul. • Inside Finish: Gypsum Board • Cavity/Frame: R-13/2x4 R-13 Wall Exterior Walls Wood Framed Wall 2x4 @ 16 in. O.C. R 13 0.101 Exterior Finish: 3 Coat Stucco • Inside Finish: Gypsum Board • Cavity/Frame: no insul. /2x4 R-0 Interior Wall Interior Walls Wood Framed Wall 2x4 @ 16 in. O.C. none 0.277 Other Side Finish: Gypsum Board SLAB FLOORS 01 02 03 04 05 06 07 08 09 Name Zone Area (ft2) Perimeter (ft) Edge Insul. R-value Carpeted Fraction Heated Status Verified Existing Condition Slab residence 6432 356 None 0.8 No Existing No BUILDING ENVELOPE - HERS VERIFICATION 01 02 03 04 Quality Insulation Installation (QII) Quality Installation of Spray Foam Insulation Building Envelope Air Leakage CFM50 Not Required Not Required Not Required n/a WATER HEATING SYSTEMS 01 02 03 04 05 06 07 08 Name System Type Distribution Type Water Heater Number of Heaters Solar Fraction N Status Verified Existing Condition DHW Sys 1 DHW Standard DHW Heater 1 2 0 Existing No Registration Number: Registration Date/Time: HERS Provider: CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version - CF1 R-06232018-1149 Report Generated at: 2019-05-20 09:57:05 CERT' \TE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE HOD ProjectlWame: Powell Ca''iculation Date/Time: 09:56, Mon, May 20, 2019 Calculation Description: Title 24 Analysis Input File Name: Powell-Traditions-Fedderly-1 9.ribdl 6x CIF �RF-01 Page 6 of 7 WATER HEATERS 01 02 03 04 05 06 07 08 09 10 11 12 Input Rating I Tank Standby Heater Tank Uniform Energy Pilot / Insulation Loss / First Hour Tank Location Element Number Volume Factor / Energy Thermal R-value Recovery Rating / NEEA Heat Pump or Ambient Name Type Tank Type of Units (gal) Factor / Efficiency Efficiency (IntlExt) Eff Flow Rate Brand / Model Condition DHW Heater 1 Gas Small Storage 2 1 50 1 0.55 EF I — 75 kBtu/hr 0 n/a n/a I n/a I n/a SPACE CONDITIONING SYSTEMS 01 02 03 04 05 06 07 08 Distribution Verified Existing SC Sys Name System Type Heating Unit Name Cooling Unit Name Fan Name Name Status Condition HVAC1 Other Heating and Cooling Heating Component 1 Cooling Component 1 HVAC Fan 1 Air Distribution Existing No System System 1 HVAC - DISTRIBUTION SYSTEMS 01 02 03 04 05 06 07 08 09 10 Insulation Supply Duct Return Duct Verified Existing HERS Name Type Duct Leakage R-value Location Location Bypass Duct Status Condition Verification Air Distribution Ducts located in attic Existing (not (Ventilated and 4.2 Attic Attic None Existing No n/a System 1 Unventilated) specified) IAQ (Indoor Air Quality) FANS 01 02 03 04 05 06 Dwelling Unit IAQ CFM IAQ Watts/CFM IAQ Fan Type IAQ Recovery Effectiveness(%) HERS Verification SFam IAQVentRpt 0 0.25 Default 0 Not Required Registration Number: Registration DateMme: HERS Provider: CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version - CF1 R-06232018-1149 Report Generated at: 2019-05-20 09:57:05 CERTI( TE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE r �OD Project fame: Powell Calculation Date/Time: 09:56, Mon, May 20, 2019 Calculation Description: Title 24 Analysis Input File Name: Powell-Traditions-Fedderly-19.ribd16x CF ;RF-01 Page 7 of 7 DOCUMENTATION AUTHOR'S DECLARATION STATEMENT 1. 1 certify that this Certificate of Compliance documentation is accurate and complete. Documentation Author Name: Documentation Author Si acre: Jon d. Scott Jon d. Scott Company: Signature Date: Scott Design and Title 24, Inc, 5/20/2019 Address: CEA/HERS Certification Identification (If applicable): 74818 Velie Way Suite 8 city/stat�51:m Desert, CA 92260 Phone: (760) 200-4780 RESPONSIBLE PERSON'S DECLARATION STATEMENT I certify the following under penalty of perjury, under the laws of the State of California: 1. 1 am eligible under Division 3 of the Business and Professions Code to accept responsibility for the building design identified on this Certificate of Compliance. 2. 1 certify that the energy features and performance specifications identified on this Certificate of Compliance conform to the requirements of Title 24, Part 1 and Part 6 of the California Code of Regulations. 3. The building design features or system design features identified on this Certificate of Compliance are consistent with the information provided on other applicable compliance documents, worksheets, calculations, plans and specifications submitted to the enforcement agency for approval with this building permit application. Responsible ❑esIgner Name: Responsible Designer Signature: Lance Fedderly Company: Date Signed: Fedderly & Associates Address: License: 38-747 Nopales Road City/State/Zip: Palm Desert, CA 92211 Phone: (760) 773-5205 Registration Number: Registration DateMme: HERS Provider: CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version - CF1 R-06232018-1149 Report Generated at: 2019-05-20 09:57:05 RESIDENTIAL MEASURES SUMMARY RMS-1 Project Name Powell Residence Building Type m Single Family ❑ Addition Alone ❑ Multi Family m Existing+ Addition/Alteration Date 512012019 Project Address 78-371 Talking Rock Turn La Quinta California Energy Climate Zone CA Climate Zone 15 Total Cond. Floor Area 6,432 Addition 0 # of Units 1 INSULATION Construction Type Cavity Area ft Special Features Status Roof Wood Framed Attic R 11 6,432 Existing Wall Wood Framed Wall Wood Framed R 13 R 13 842 460 Existing Existing Wall Wood Framed R 13 697 Existing Wall Wood Framed R 13 808 Existing Slab Unheated Slab -on -Grade - no insulation 6,432 Perim = 356' Existing Demising Wood Framed - no insulation 365 Existing FENESTRATION Orientation Area ft2 Total Area: 1,542 Glazing Percentage. 24.0% NeWfAltered Average U-Factor. U-Fac SHGC Overhang Sidefins Exterior Shades 0-30 Status Left (VV) 96.0 0.300 0.20 none none Bug Screen New Left (W) 88.0 0.710 0.60 none none Bug Screen Existing Rear (N) 99.0 0.710 0.60 none none Bug Screen Existing Rear (N) 590.0 0.300 0.20 none none Bug Screen New Right (E) 228.6 0.710 0.60 none none Bug Screen Existing Right (E) 100.0 0.300 0.20 none none Bug Screen Altered Front (S) 192.0 0.300 0.20 none none Bug Screen Altered Front (S) 148.8 0.710 0.60 none none Bug Screen Existing HVAC SYSTEMS Qty. Heating Min. Eff Cooling Min. Eff Thermostat Status 5 Central Furnace 80% AFUE Split Air Conditioner 12.0 SEER Setback Existing HVAC DISTRIBUTION Location Heating Cooling Duct Duct Location R-Value Status HVAC Ducted Ducted Attic 4.2 Existing WATER HEATING Qty. Type Gallons Min. Eff Distribution Status Ener Pro 7.2 by Ene Soft User Number: 6712 ID: Page 10 of 21 _to, k 2016 Low -Rise Residential Mandatory Measures Summary NOTE: Low-rise residential buildings subject to the Energy Standards must comply with all applicable mandatory measures, regardless of the compliance approach used. Review the respective section for more information. 'Exceptions may apply, Revised 041ZUI Building Envelope Measures: § 110.6(a)l: Air Leakage. Manufactured fenestration, exterior doors, and exterior pet doors must limit air leakage to 0.3 cfm/ft' or less when tested per NFRC-400 or ASTM E283 or AAMA/WDMA/CSA 101/I.S.2/A440-2011.' § 110.6(a)5: Labeling. Fenestration products must have a label meeting the requirements of § 10-111(a). § 110.6(b): Field fabricated exterior doors and fenestration products must use U-factors and solar heat gain coefficient (SHGC) values from TABLES 110.6•A and 110.6-B for compliance and must be caulked andfor wealherstri ed.' Air Leakage. All joints, penetrations, and other openings in the building envelope that are potential sources of air leakage must be caulked, § 110.7: asketed, or weather stripped. § 110.8(a): Insulation Certification by Manufacturers. Insulation specified or installed must meet Standards for Insulating Material. § 110.8(g): Insulation Requirements for Heated Slab Floors. Heated slab floors must be insulated per the requirements of § 110.8(g). Roofing Products Solar Reflectance and Thermal Emittance. The thermal emittance and aged solar reflectance values of the roofing § 110.8(i): material must meet the requirements of § 110.8 i when the installation of a cool roof is specified on the CF1 R. § 110.80): Radiant Barrier. A radiant barrier must have an emittance of 0.05 or less and be certified to the Department of Consumer Affairs. Ceiling and Rafter Roof Insulation. Minimum R-22 insulation in wood -frame ceiling; or the weighted average U-factor must not exceed 0.043. Minimum R-19 or weighted average U-factor of 0.054 or less in a rafter roof alteration. Attic access doors must have permanently attached § 150.0(a): insulation using adhesive or mechanical fasteners. The attic access must be gasketed to prevent air leakage. Insulation must be installed in direct contact with a continuous roof or ceiling which is sealed to limit infiltration and exfiltration as specified in § 110.7, including but not limited to placing insulation either above or below the roof deck or on top of a drywall ceilinq: § 150.0(b): Loose -fill Insulation. Loose fill insulation must meet the manufacturer's required density for the labeled R-value. Above Grade Wall Insulation. Minimum R-13 insulation in 2x4 inch wood framing wall or have a U-factor of 0.102 or less (R-19 in 2x6 or U- § 150.0(c): factor of 0.074 or less). Opaque non -framed assemblies must have an overall assembly U-factor not exceeding 0.102, equivalent to an installed value of R-13 in a wood framed assembly.' § 150.0(d): Raised -Floor Insulation. Minimum R-19 insulation in raised wood framed floor or 0.037 maximum U-factor.' § 150.0(f): Slab Edge Insulation. Slab edge insulation must meet all of the following: have a water absorption rate, for the insulation material alone without facings, no greater than 0.3%; have a water vapor permeance no greater than 2.0 perm/inch; be protected from physical damage and UV light dalarinrafinn• and when installer/ ac nart of a heated Clad 111mr. mAP_I the rP_auirPmPntS of & 110.8f6. 1500 1 Vapor Retarder. In Climate Zones 1-16, the earth floor of unvented crawl space must be covered with a Class I or Class II vapor retarder. This § (g) requirement also applies to controlled ventilation crawls ace for bulldln s wi-ripiying with the exce tlon to 2 150.0 d . Vapor Retarder. In Climate Zones 14 and 16, a Class I or Class II vapor retarder must be installed on the condilioned space side of all § 150.0(g)2: insulation in all exterior walls, vented attics, and unvented attics with air -permeable Insulation. Fenestration Products. Fenestration, including skylights, separating conditioned space from unconditioned space or outdoors must have a § 150.0(q): maximum U-factor of 0.58• or the weighted average U-factor of all fenestration must not exceed 0.58.' Fireplaces, Decorative Gas Appliances, and Gas Log Measures: § 150.0(e)lA: Closable Doors. Masonry or factory -built fireplaces must have a closable metal or glass door covering the entire opening of the firebox. § 150.0(e)l B: Combustion Intake. Masonry or factory -built fireplaces must have a combustion outside air intake, which is at least six square inches in area and is eV[pped with a readily accessible ❑ erable and fight-fittingfight-fiffing damper or combustion -air control device' § 150.0(e)1 C: Flue Damper. Masonry or factory -built fireplaces must have a flue damper with a readily accessible control.' Pilot Light. Continuous burning pllot lights and the use of indoor air for cooling a firebox jacket, when that indoor air is vented to the outside of § 150.0(e)2: the building, are prohibited. Space Conditioning, Water Heating, and Plumbing System Measures: § 110.0-§ 110.3: Certification. Heating, ventilation and air conditioning (HVAC) equipment, water heaters, showerheads, faucets, and all other regulated appliances must be certified by the manufacturer to the Energy Commission.' § 110.2(a): HVAC Efficiency. Equipment must meet the applicable efficiency requirements in TABLE 110.2-A through TABLE 110.2-K.' Controls for Heat Pumps with Supplementary Electric Resistance Heaters. Heat pumps with supplementary electric resistance heaters must have controls that prevent supplementary heater operation when the heating load can be met by the heat pump alone; and in which the § 110.2(b): cut -on temperature for compression heating is higher than the cut -on temperature for supplementary heating, and the cut-off temperature for compression heating is higher than the cut-off temperature for supplementary heating.' Thermostats. All unitary heating or cooling systems not controlled by a central energy management control system (FMCS) must have a § 110.2(c): setback thermostat.' Water Heating Recirculation Loops Serving Multiple Dwelling Units. Water heating recirculation loops serving multiple dwelling units must § 110.3(c)5: meet the air release valve, backflow prevention, pump priming, pump isolation valve, and recirculation loop connection requirements of § 110.3(c)5. § 110.3(c)7: Isolation Valves. Instantaneous water heaters with an input rating greater than 6.8 kBTU/hr (2 kW) must have isolation valves with hose bibbs or other fittings on both cold water and not water lines of water heating systems to allow for water tank Ti us hing when the valves are closed. r5l 0.5:Pilot Lights. Continuously burning pilot lights are prohibited for natural gas: fan -type central furnaces; household cooking appliances (appli- ances without an electrical sir volts a connection with ilot li hts that consume less than 150 Btu/hr are exem t); and ool ands a heaters.' Building Cooling and Heating Loads. Heating and/or cooling loads are calculated In accordance with ASHRAE Handbook, Equipment 0.0(h)1: Volume, Applications Volume, and Fundamentals Volume; SMACNA Residential Comfort System Installation Standards Manual; or ACCA Manual J usino desion conditlons soecifled in & 150.0(h)2. 2016 Low -Rise Residential Mandatory Measures Summary § 150.0(h)3A: Clearances. Installed air conditioner and heat pump outdoor condensing units must have a clearance of at least 5 feet from the outlet of any dryer vent. § 150.0(h)3B: Liquid Line Drier. Installed air conditioner and heat pump systems must be equipped with liquid line filter driers if required, as specified by manufacturer's Instructions. § 150.00)1: Storage Tank Insulation. Unfired hot water tanks, such as storage tanks and backup storage tanks for solar water -heating systems, must have R-12 external insulation or R-16 Internal insulation where the internal insulation R-value is indicated on the exterior of the tank. Water piping and cooling system line insulation. For domestic hot water system piping, whether buried or unburied, all of the following must be insulated according to the requirements of TABLE 120.3-A: the first 5 feet of hot and cold water pipes from the storage tank; all piping with a § 150.00)2A: nominal diameter of 3/4 inch or larger; all piping associated with a domestic hot water recirculation system regardless of the pipe diameter; piping from the heating source to storage tank or between tanks; piping buried below grade; and all hot water pipes from the heating source to kitchen fixtures.' § 150.0Q)2B: Water piping and cooling system line insulation. All domestic hot water pipes that are buried below grade must be installed in a water proof and non -crushable casing or sleeve.' § 150.00)2C: Water piping and cooling system line insulation. Pipe for cooling system lines must be insulated as specified in § 150.00)2A. Distribution piping for steam and hvdronic heating systems or hot water systems must meet the requirements in TABLE 120.3-A.' § 150.00)3: Insulation Protection. Insulation must be protected from damage, including that due to sunlight, moisture, equipment maintenance, and wind. Insulation Protection. Insulation exposed to weather must be installed with a cover suitable for outdoor service. For example, protected by § 150.00)3A: aluminum, sheet metal, painted canvas, or plastic cover. The cover must be water retardant and provide shielding from solar radiation that can cause degradation of the material. § 150.00)3B: Insulation Protection. Insulation covering chilled water piping and refrigerant suction piping located outside the conditioned space must have a Class I or Class II vapor retarder. Gas or Propane Systems. Systems using gas or propane water heaters to serve individual dwelling units must include all of the following: a § 150.0(n)l: 120V electrical receptacle within 3 feet of the water heater; a Category III or IV vent, or a Type B vent with straight pipe between the outside termination and the space where the water heater is installed; a condensate drain that is no more than 2 inches higher than the base of the water heater, and allows natural draining without pump assistance; and a gas supply line with a capacity of at least 200,000 Btu/hr. § 150.0(n)2: Recirculating Loops. Recirculating loops serving multiple dwelling units must meet the requirements of § 110.3(c)5. § 150.0(n)3: Solar Water -heating Systems. Solar water -heating systems and collectors must be certified and rated by the Solar Rating and Certification Corporation SRCCI or by a listing agency that is approved by the Executive Director. Ducts and Fans Measures: § 110.8(d)3: Ducts. Insulation installed on an existing space -conditioning duct must comply with § 604.0 of the California Mechanical Code (CMC). If a contractor installs the insulation, the contractor must certify to the customer, in writing, that the insulation meets this requirement. CMC Compliance. All air -distribution system ducts and plenums must be installed, sealed, and insulated to meet the requirements of CMC §§ 601.0, 602.0, 603.0, 604.0, 605.0 and ANSI/SMACNA-006-2006 HVAC Duct Construction Standards Metal and Flexible 3rd Edition. Portions of supply -air and return -air ducts and plenums must be insulated to a minimum installed level of R-6.0 (or higher if required by CMC § 605.0) or a minimum installed level of R-4.2 when entirely in conditioned space as confirmed through field verification and diagnostic testing § 150.0(m)l: (RA3.1.4.3.8). Connections of metal ducts and inner core of Flexible ducts must be mechanically fastened. Openings must be sealed with mastic, tape, or other duct -closure system that meets the applicable requirements of UL 181, UL 181A, or UL 181B or aerosol sealant that meets the requirements of UL 723. If mastic or tape is used to seal openings greater than % inch, the combination of mastic and either mesh or tape must be used. Building cavities, support platforms for air handlers, and plenums designed or constructed with materials other than sealed sheet metal, duct board or flexible duct must not be used for conveying conditioned air. Building cavities and support platforms may contain ducts. Ducts installed in cavities and support platforms must not be compressed to cause reductions In the cross -sectional area of the ducts.' Factory -Fabricated Duct Systems. Factory -fabricated duct systems must comply with applicable requirements for duct construction, § 150.0(m)2: connections, and closures; joints and seams of duct systems and their components must not be sealed with cloth back rubber adhesive duct tapes unless such tape is used in combination with mastic and draw bands. § 150.0(m)3: Field -Fabricated Duct Systems. Field -fabricated duct syslems must comply with applicable requirements for: pressure -sensitive tapes, mastics, sealants, and other requirements specified for duct construction. § 150.0(m)7: Backdraft Dampers. All fan systems that exchange air between the conditioned space and the outside of the bul[di ng must have back draft or automatic dampers. § 150.0(m)8: Gravity Ventilation Dampers. Gravity ventilating systems serving conditioned space must have either automatic or readily accessible, manually operated dampers in all openings to the outside, except combustion inlet and outlet air openings and elevator shaft vents. Protection of Insulation. Insulation must be protected from damage, including that due to sunlight, moisture, equipment maintenance, and § 150.0(m)9: wind. Insulation exposed to weather must be suitable for outdoor service. For example, protected by aluminum, sheet metal, painted canvas, or plastic cover. Cellular foam insulation must be protected as above or painted with a coating that is water retardant and provides shielding from solar radiation. § 150.0(m)10: Porous Inner Core Flex Duct. Porous inner core flex duct must have a non -porous layer between the inner core and outer vapor barrier. Duct System Sealing and Leakage Test. When space conditioning systems use forced air duct systems to supply conditioned air to an § 150.0(m)l l occupiable space, the ducts must be sealed and duct leakage tested, as confirmed through field verification and diagnostic testing, in accordance with 150.0 m l land Reference Residential Appendix RA3. Air Filtration. Mechanical systems that supply air to an occupiable space through ductwork exceeding 10 feet In length and through a thermal § 150.0(m)12: conditioning component, except evaporative coolers, must be provided with air filter devices that meet the design, installation, efficiency, pressure drop, and labeling requirements of § 150.0 m 12. a 2016 Low -Rise Residential Mandatory Measures Summary Duct System Sizing and Air Filter Grille Sizing. Space conditioning systems that use forced air ducts to supply cooling to an occupiable space must have a hole for the placement of a static pressure probe (HSPP), or a permanently installed static pressure probe (PSPP) in the § 150.0(m)13: supply plenum. -The space conditioning system must also demonstrate airflow >- 350 CFM per ton of nominal cooling capacity through the return grilles, and an air -handling unit fan efficacy <_ 0.58 WICFM as confirmed by Feld verification and diagnostic testing, in accordance with Reference Residential Appendix RA3.3. This applies to both single zone central forced air systems and every zone for zonally controlled central forced airs stems: Ventilation for Indoor Air Quality. All dwelling units must meet the requirements of ASHRAE Standard 62.2. Neither window operation nor §150.0(o): continuous operation of central forced air system air handlers used in central fan integrated ventilation systems are permissible methods of providing whole-buildIng ventilation. § 150.0(o)1A: Field Verification and Diagnostic Testing. Whole-building.ventilation airflow must be confirmed through field verification and diagnostic testing, in accordance with Reference Residential Appendix RAU. Pool and Spa Systems and Equipment Measures: Certification by Manufacturers. Any pool or spa heating system or equipment must be certified to have all of the following: a thermal efficiency § 110.4(a): that complies with the Appliance Efficiency Regulations; an on -off switch mounted outside of the heater that allows shutting off the heater without adjusting the thermostat setting; a permanent weatherproof plate or card with operating instructions; and must not use electric resistance heating.' § 110.4(b)1: Piping. Any pool or spa heating equipment must be installed with at least 36 inches of pipe between the filter and the heater, or dedicated suction and return lines, or built-in or built-up connections t6 allavi for future solar heating. § 110.4(b)2: Covers. Outdoor pools or spas that have a heat pump or gas heater must have a cover. § 110.4(b)3: Directional inlets and time switches for pools. Pools must have directional inlets that adequately mix the pool water, and a time switch that will allow all pUmDs to be set or programmed to run only during off-peak electric demand periods, § 110.5: Pilot Light. Natural gas pool and spa heaters must not have a continuously burning pilot light. 150.0 § (p)' Pool Systems and Equipment Installation. Residential pool systems or equipment must meet the specified requirements for pump sizing, flow rate, piping, filters, and valves.' Lighting Measures: § 110.9: Lighting Controls and Components. All lighting control devices and systems, ballasts, and luminaires must meet the applicable requirements of 110.9., § 110.9(e): JA8 High Efficacy Light Sources. To qualify as a JA8 high efficacy light source for compliance with § 150.0(k), a residential light source must be certified to the Energy Commission according to Reference Joint Appendix JA8. § 150.0(k)1A: Luminaire Efficacy. All installed luminaires must be high efficacy in accordance with TABLE 150.0-A. )§ Blank Electrical Boxes. The number of electrical boxes that are more than 5 feet above the finished floor and do not contain a luminaire or 150.0(k)l B: other device must be no greater than the number of bedrooms. These electrical boxes must be served by a dimmer, vacancy sensor control, or fanspeed control. Recessed Downlight Luminaires in Ceilings. Luminaires recessed into ceilings must meet all of the requirements for: insulation contact (IC) § 150.0(k)l C: labeling; air leakage; sealing; maintenance; and socket and light source as described in § 150.0(k)1C. A JA8-2016-E light source rated for elevated temperature must be installed by final inspection in all recessed downli ht luminaires in ceilings. § 150.0(k)1 D: Electronic Ballasts. Ballasts for fluorescent lamps rated 13 watts or greater must be electronic and must have an output frequency no less than 20 kHz. Night Lights. Permanently installed night lights and night lights integral to installed luminaires or exhaust fans must be rated to consume no § 150.0(k)l E: more than 5 watts of power per luminaire or exhaust fan as determined in accordance with § 130.0(c). Night lights do not need to be controlled by vacancy sensors. § 150.0(k)1 F: Lighting Integral to Exhaust Fans. Lighting integral to exhaust fans (except when installed by the manufacturer in kitchen exhaust hoods) must meet the applicable requirements of § 150.0(k).' Screw based luminaires. Screw based luminaires must not be recessed downlight luminaires in ceilings and must contain lamps that comply § 150.0(k)1G: with Reference Joint Appendix JA8. Installed lamps must be marked with "JA8-2016" or "JA8-2016-E" as specified in Reference Joint Appendix JA8.' § 150.0(k)1 H: Enclosed Luminaires. Light sources installed in enclosed luminaires must be JA8 compliant and must be marked with "JA8-2016-E." § 150.0(k)2A: Interior Switches and Controls. All forward phase cut dimmers used with LED light sources must comply with NEMA SSL 7A. § 150.0(k)2B: Interior Switches and Controls. Exhaust fans must be switched separately from lighting systems.' § 150.0(k)2C: Interior Switches and Controls. Luminaires must be switched with readily accessible controls that permit the luminaires to be manually switched ON and OFF. § 150.0(k)2D: Interior Switches and Controls. Controls and equipment must be installed in accordance with manufacturer's instructions. § 150.0(k)2E: Interior Switches and Controls. No control must bypass a dimmer or vacancy sensor function if the control is installed to comply with 150.0(k). § 150.0(k)2F: Interior Switches and Controls. Lighting controls must comply with the applicable requirements of § 110.9. Interior Switches and Controls. An energy management control system (EMCS) may be used to comply with dimmer requirements if it: § 150.0(k)2G: functions as a dimmer according to § 110.9; meets the Installation Certificate requirements of § 130.4; meets the EMCS requirements of § 130.5 - and meets all other requirements in § 150.0(k)2. Interior Switches and Controls. An EMCS may be used to comply with vacancy sensor requirements in § 150.0(k) if it meets all of the § 150.0(k)2H: following: it functions as a vacancy sensor according to § 110.9; the Installation Certificate requirements of § 130.4; the EMCS requirements of § 130.5 ; and all other requirements in § 150.0(k)2. § 150.0(k)21: Interior Switches and Controls. A multiscene programmable controller may be used to comply with dimmer requirements in § 150.0(k) if it provides the funcliartallty of a dimmer accordin to § 110.9, and complies with all other applicable requirements in § 150.0(k)2. 2016 Low -Rise Residential Mandatory Measures Summary § 150.0(k)2J: Interior Switches and Controls. In bathrooms, garages, laundry rooms, and utility rooms, at least one luminaire in each of these spaces must be controlled by a vacancy sensor. § 150.0(k)2K: Interior Switches and Controls. Dimmers or vacancy sensors must control all luminaires required to have light sources compliant with Reference Joint Appendix JAB, except luminaires in closets less than 70 square feet and luminaires in hallways.' § 150.0(k)2L: Interior Switches and Controls. Undercabinet lighting must be switched separately from other lighting systems. Residential Outdoor Lighting. For single-family residential buildings, outdoor lighting permanently mounted to a residential building, or to other § 150.0(k)3A: buildings on the same lot, must meet the requirement in item § 150.0(k)3Ai (ON and OFF switch) and the requirements in either item § 150.0(k)3Aii (photocell and motion sensor) or item § 150.0(k)3Aiii (photo control and automatic time switch control, astronomical time clock, or EMCS. Residential Outdoor Lighting. For low-rise multifamily residential buildings, outdoor lighting for private patios, entrances, balconies, § 150.0(k)3B: and porches; and outdoor lighting for residential parking lots and residential carports with less than eight vehicles per site must comply with either § 150.0(k)3A or with the applicable requirements in §§ 110.9.130.0. 130.2, 130.4, 140.7 and 141.0. § 150.0(k)3C: Residential Outdoor Lighting. For low-rise residential buildings with four or more dwelling units, outdoor lighting not regulated by § 150.0(k)3B or § 150.0(k)3D must comply with the applicable requirements in §§ 110.9, 130.0, 130.2, 130.4.140.7 and 141.0. § 150.0(k)3D: Residential Outdoor Lighting. Outdoor lighting for residential parking lots and residential carports with a total of eight or more vehicles per site must comply with the applicable requirements in §§ 110.9,130.0,_130.2, 130.4. 140.7, and 141.0. § 150.0(k)4: Internally illuminated address signs. Internally illuminated address signs must comply with § 140.8; or must consume no more than 5 watts of power as determined according to § 130.0 c . § 150.0(k)5: Residential Garages for Eight or More Vehicles. Lighting for residential parking garages for eight or more vehicles must comply with the applicable requirements for nonresidential garages in §§ 110.9, 130.0, 130.1. 130.4,140.6, and 141.0. Interior Common Areas of Low-rise Multi -Family Residential Buildings. In a low-rise multifamily residential building where the total interior § 150.0(k)6A: common area in a single building equals 20 percent or less of the floor area, permanently installed lighting for the interior common areas in that building must be high efficacy luminaires and controlled by an occupant sensor. Interior Common Areas of Low-rise Multi -Family Residential Buildings. In a low-rise multifamily residential building where the total interior common area in a single building equals more than 20 percent of the floor area, permanently installed lighting in that building must: § 150.0(k)6B: i. Comply with the applicable requirements in §§ 110.9, 130.0, 130.1, 140.6 and 141.0; and ii. Lighting installed in corridors and stairwells must be controlled by occupant sensors that reduce the lighting power in each space by at least 50 percent. The occupant sensors must be capable of turning the light fully on and off from all designed paths of inqress and egress. Solar Ready Buildings: Single Family Residences. Single family residences located in subdivisions with ten or more single family residences and where the § 110.10(a)1: application for a tentative subdivision map for the residences has been deemed complete by the enforcement agency must comply with the re ulrements of § 110.10 b th roug h § 110.10 Le). 1§ 110.10(a)2: Low-rise Multi -family Buildings. Low-rise multifamily buildings must comply with the requirements of § 110.10(b) through § 110.10(d). Minimum Area. The solar zone must have a minimum total area as described below. The solar zone must comply with access, pathway, smoke ventilation, and spacing requirements as specified in Title 24, Part 9 or other Parts of Title 24 or in any requirements adopted by a local jurisdiction. The solar zone total area must be comprised of areas that have no dimension less than 5 feet and are no less than 80 square feet each for buildings with roof areas less than or equal to 10,000 square feet or no less than 160 square feet each for buildings with roof areas § 110.10(b)1: greater than 10,000 square feet. For single family residences the solar zone must be located on the roof or overhang of the building and have a total area no less than 250 square feet. For low-rise multi -family buildings the solar zone must be located on the roof or overhang of the building, or on the roof or overhang of another structure located within 250 feet of the building, or on covered parking installed with the building project, and have a total area no less than 15 perrerit of the total roof area of the building excluding any sk li ht area.' § 110.10(b)2: Orientation. All sections of the solar zone located on steep -sloped roofs must be oriented between 110 degrees and 270 degrees of true north. § 110.10(b)3A: Shading. The solar zone must not contain any obstructions, including but not limited to: vents, chimneys, architectural features, and roof mounted equipment.' Shading. Any obstruction located on the roof or any other part of the building that projects above a solar zone must be located at least twice the § 110.10(b)3B: distance, measured in the horizontal plane, of the height difference between the highest point of the obstruction and the horizontal projection of the nearest point of the solar zone, measured in the vertical plane.' § 110.10(b)4: Structural Design Loads on Construction Documents. For areas of the roof designated as solar zone, the structural design loads for roof dead load and roof live load must be clearly indicated on the construction documents. Interconnection Pathways. The construction documents must indicate: a location for inverters and metering equipment and a pathway for § 110.10(c): routing of conduit from the solar zone to the point of interconnection with the electrical service (for single family residences the point of interconnection will be the main service panel); and a pathway for routing of plumbing from the solar zone to the water -heating system. § 110.10(d): Documentation. A copy of the construction documents or a comparable document indicating the information from § 110.10(b) through 110.1 0c must be provided to the occupant. § 110.10(e)1: Main Electrical Service Panel. The main electrical service panel must have a minimum busbar rating of 200 amps. Main Electrical Service Panel. The main electrical service panel must have a reserved space to allow for the installation of a double pole circuit § 110.10(e)2: breaker for a future solar electric installation. The reserved space must be: positioned at the opposite (load) end from the input feeder location or main circuit location; and permanently marked as "For Future Solar Electric". HVAC SYSTEM HEATING AND COOLING LOADS SUMMARY Project Name 'lowell Residence Date 5/20/2019 System Name HVAC Floor Area 6,432 ENGINEERING CHECKS SYSTEM LOAD Number of Systems 6 COIL CFM Total Room Loads 7,350 Return Vented Lighting Return Air Ducts Return Fan Ventilation 1,319 Supply Fan Supply Air Ducts TOTAL SYSTEM LOAD COOLING PEAK COIL HTG. PEAK Heating System Sensible Latent CFM Sensible Output per System 89,000 117.228 8,245 2,510 93.093 Total Output Btuh 445,000 0 Output Btuhls ft 69.2 9,9401 6,614 Cooling System 0 0 Output per System 57,800 49,206 15,169 1,319 60,870 Total Output Btuh 289,000 0 23,414 0 Total Output Tons 24.1 9,940 6,614 Total Output Btuhls ft 44.9 Total Output s ftlTon 267.1 186,312 167,191 Air System CFM per System 2.000 HVAC EQUIPMENT SELECTION Airflow cfm 10,000 Existing HVAC 228,584 36,098 445,000 Airflow (cfm/s ft) 1.55 Airflow cfmlTon 415.2 Outside Air % 13.2% Total Adjusted System Output (Adjusted for Peak Design conditions) TIME OF SYSTEM PEAK 228,584 36,098 445,000 Jan 1 AM Outside Air cfmis ft 0.21 Nate: values above _given at ARI conditions Aug 3 PM HEATING SYSTEM PSYCHROMETRICS Airstream Temperatures at Time of Heating Peak) 26 OF �— Outside Air 1,319 cfm 69 OF 64 OF 105 OF 105 OF Q Heating Coil Supply Fan 10,000 cfm 0 105 F ROOM 70 OF COOLING SYSTEM PSYCHROMETRICS Airstream Temperatures at Time of Cooling Peak 112/78°F Outside Air 1,319 cfm 77/65OF 82/67OF 60159OF 60/59OF _ Cooling Coil Supply Fan 10,000 cfm 61 / 59 OF 54.5%u ROOM il 76/65OF ROOM LOAD SUMMARY Project Name Powell Residence Date 512012019 System Name HVAC Floor Area 6,432 ROOM LOAD SUMMARY ROOM COOLING PEAK COIL COOLING PEAK COIL HTG. PEAK Zone Name Room Name Mult. CFM Sensible Latent CFM I Sensible Latent CFM Sensible residence existing 78-371 Talking Ri 1 7,350 117,226 8,245 7,350 117,226 8,245 2,510 93,093 PAGE TOTAL 1 7.350 117.226 8,245 2,510 93,093 TOTAL 1 7.350 117,226 8,245 2.510 93,093 Total includes ventilation load for zonal systems. ROOM HEATING PEAK LOADS Project Name Date Powell Residence 512012019 ROOM INFORMATION DESIGN CONDITIONS Room Name existing 78-371 Talking Rock Turn Floor Area 6,432.00 ftZ Indoor Dry Bulb Temperature 70 °F Time of Peak Jan 1 AM Outdoor Dry Bulb Temperature 26 OF Conduction 1.064 Area X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X to Ceiling U-Value X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X AT OF = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = 44 Btu/hr Default 1978 to present... 6,432.0 0.0790 44 22,358 R-13 Wall 2,807.6 0.1020 44 12,600 .301.20 dual low a 978.0 0.3000 44 12,910 Existing Window 564.4 0.7100 44 17.633 Slab -On -Grade perim = 356.0 0.7300 44 11,435 Items shown w.th an asterisk (') denote conduction Infiltration:[ 1.00 X Schedule Air Sensible Fraction through an interior surface X 6,432 X Area another room 12.30 X 0.262 Height ACH Page Total / 60 ] X AT 76,935 = 16,158 TOTAL HOURLY HEAT LOSS FOR ROOM 93,093 RESIDENTIAL ROOM COOLING LOAD SUMMARY Project Name Date Powell Residence 512012019 ROOM INFORMATION DESIGN CONDITIONS Room Name existing 78-371 Talking Rock Turn Outdoor Dry Bulb Temperature 112 OF Floor Area 6,432.00 ft2 Outdoor Wet Bulb Temperature 78 OF Indoor Dry Bulb Temperature 76 OF, Outdoor Daily Range: 34 OF Opaque Surfaces Default 1978 to present... R-13 Well R-13 Wall R-13 Wall R-13 Wall Orientation (SE) Area X X X X X X X X X U-Factor 0.0790 X X X X X X X X X CLTD' = = = = = = = = = 6,432.0 56.0 842.0 0.1020 32.1 460.0 0.1020 29.0 697.4 0.1020 31.2 808.2 0.1020 28.2 Page Total Items shown with an asterisk (') denote conduction through an interior surface to another room. 1. Cooling Load Temperature Difference (CLTD) Shaded Unshaded Fenestration 5-1 EXISTING DR WNDW sLiDR.-E2 EXISTING DR WNDW SLDR.-3 EXISTING DR WNDW SLDR-4 EXISTING DR WNDW SLDR-5 EXISTING DR WNDW SLDR-6 b--7 EXISTING DR WNDW SLDR-8 3--9 r1riPntatinn (w) (W) (W) (W) (W) (W) (W) (N) (N) Area X X X X X X X X X GLF + + + + + + + + + Area X X X X X X X X X GLF = = = = = = = = = 0.0 13.4 60.0 24.4 0.0 36.5 36.0 69.4 0.0 36.5 22.8 69.4 0.0 36.5 11.0 69.4 0.0 36.5 9.1 69.4 0.0 36.5 9.1 69.4 0.0 13.4 36.0 24.4 0.0 36.5 18.0 55.8 0.0 13.4 140.0 19.9 Page Total Btu/hr 28,455 2,766 1,361 Z221 37,1211 Btu/hr 1,465 2.500 1,583 764 633 633 879 1,004 2, 779 1Z241 Internal Gain Stulhr Occupants 19•3 Occupants X 245 Btuh/occ. 4. Equipment 6,432 1 Floor Area X 0.50 w/sgft Infiltration: 1.064 X 0.02 X 362.56 X 36 12,: Air Sensible CFM Ei.A AT I TOTAL HOURLY SENSIBLE HEAT GAIN FOR ROOM 117,2261 Latent Gain Btu/hr Occupants 19 3 Occupants X 155 Btuh/occ. = 2,991 Infiltration: 4,771 X 0.88 X 362.56 X 0.00344' = 5,254 Alr Latent CFM ELA AW TOTAL HOURLY LATENT HEAT GAIN FOR ROOM 2,9911 RESIDENTIAL ROOM COOLING LOAD SUMMARY Project Name Date Powell Residence 512012019 ROOM INFORMATION DESIGN CONDITIONS Room Name existing 78-371 Talking Rock Turn Outdoor Dry Bulb Temperature 112 OF Floor Area 6,432.00 ftZ Outdoor Wet Bulb Temperature 78 OF Indoor Dry Bulb Temperature 76 OF, Outdoor Daily Range: 34 OF Surfaces Orientation Area U-Factor CLTD' X X = X X = X X = X X = X X = X X = X X = X X = X X = Page Total Items shown with an asterisk (") denote conduction through an interior surface to another room. 1. Cooling Load Temperature Difference (CLTD) Shaded Unshaded Fenestration 2-10 1-11 EXISTING DR WNDW SLDR 12 EXISTING DR WNDW SLDR-13 EXISTING DR WNDW SLDR-14 EXISTING DR WNDW SLDR-15 EXISTING DR WNDW SLDR-16 EXISTING DR WNDW SLDR-17 EXISTING DR WNDW SLDR-18 {7ripntation (N) (N) (N) (N) (N) (E) (E) (E) (E) Area X X X X X X X X GLF + + + + + + + + Area X X X X X X X X GLF = = = = = = = = 0.0 13.4 300.0 19.9 0.0X 13.4+ 150.0X 19.9= 0.0 36.5 12.0 55.8 0.0 36.5 12.0 55.8 0.0 36.5 57.0 55.8 0.0 36.5 84.0 64.8 0.0 36.5 49.0 64.8 0.0 36.5 35.01 1 64.8 0.0 36.5 18.01 1 64.8 Page Total Btulhr Btulhr 5, 956 2, 978 669 2,178 5, W 3,177 Z269 1,167 25,5091 Internal Gain Btulhr Occupants 19.3 Occupants X 245 Btuh/occ. C Equipment 6,432 1 Floor Area X 0.50 W/sgft Infiltration: i.D64 X 0,88 X 362.56 X 36 = C Alr Sensible CFM ELA 1T I TOTAL HOURLY SENSIBLE HEAT GAIN FOR ROOM 117,2261 Latent Gain Btu/hr Occupants 19•3 Occupants X 155 Btuh/occ. = 2.991 Infiltration: 4,771 X 0.88 X 362.56 X 0.00344 = 5.254 Air Latent CFNI ELA AW I TOTAL HOURLY LATENT HEAT GAIN FOR ROOM 2,9911 RESIDENTIAL ROOM COOLING LOAD SUMMARY Project Name Date Powell Residence 512012019 ROOM INFORMATION DESIGN CONDITIONS Room Name existing 78-371 Talking Rock Turn Outdoor Dry Bulb Temperature 112 OF Floor Area 6,432,00 ft' Outdoor Wet Bulb Temperature 78 OF Indoor Dry Bulb Temperature 76 OF Outdoor Daily Range: 34 OF ue Surfaces Orientation Area X X X X X X X X X U-Factor X X X X X X X X X CLTD' = - = = = = = = = Page Total Items shown with an asterisk (") denote conduction through an interior surface to another room. 1. Cooling Load Temperature Difference (CLTD) Fenestration EXISTING DR WNDW SLDR-19 4-20 EXISTING DR WNDW SLDR-21 EXISTING DR WNDW SLDR 22 4-23 a-24 EXISTING DR WNDw SLDR-25 6--26 a-27 Orientation (E) (E) (E) (E) (E) (S) (S) (S) (S) Shaded Unshaded Area X X X X X X X X X GLF + + + + + + + + + Area X X X X X X X X X GLF = = = = = = = = = 0.0 36.5 11.0 64.8 0.0 13.4 50.0 22.9 0.0 36.5 15.8 64.8 0.0 36.5 15.8 64.8 0.0 13.4 50.0 22.9 0.0 13.4 60.0 15.5 0.0 36.5 10.8 42.7 0.0 13.4 72.0 15.5 0.0 13.4 60.0 1 15.5 Page Total Btu/hr Btu/hr 713 1,144 1,024 11024 1.144 �'IdI+I I �Csirll Internal Gain Btu/hr Occupants 19.3 Occupants X 245 Btuh/occ. 4„ Equipment 6,432 Floor Area X 0.50 w/sgft Infiltration: 1.064 X 0.88 X 362.56 X Air Sensible CFM ELA AT TOTAL HOURLY SENSIBLE HEAT GAIN FOR ROOM 117,226 Latent Gain Btu/hr Occupants 19 3 Occupants X _ 155 Btuh/occ. = 2,991 Infiltration: 4,771 X 0.88 X 362.56 X 0.00344 = 5,254 Air Latent CFM ELA OW TOTAL HOURLY LATENT HEAT GAIN FOR ROOM 2,9911 RESIDENTIAL ROOM COOLING LOAD SUMMARY Project Name Date Powell Residence 512012019 ROOM INFORMATION DESIGN CONDITIONS Room Name existing 78-371 Talking Rock Turn Outdoor Dry Bulb Temperature 112 OF Floor Area 6,432.00 ftZ Outdoor Wet Bulb Temperature 78 OF Indoor Dry Bulb Temperature 76 OF, Outdoor Daily Range: 34 OF Opaque Surfaces Orientation Area U-Factor CLTD' Btu/hr X X = X X = X X = X X = X X = X X = X X = X X = X I X = Page Total 0 Items shown with an asterisk (*) denote conduction through an interior surface to another room. 1. Cooling Load Temperature Difference (CLTD) Shaded Unshaded Fenestration Orientation Area GLF Area GLF Btu/hr EXISTING DR WNDW SLDR-28 (S) 0.0 X 36.5 + 57.0 X 42.7 = 2,433 EXISTING DR WNDW SLDR-29 (S) 0.0 X 36.5 + 24.0 X 42.7 = 1,024 EXISTING DR WNDW SLDR 30 (S) 0.0 X 36.5 + 57.0 X 42.7 = 2,433 X + X = X + X = X + X = X + X = X + X = X + X = Page Total 5,8s0 Internal Gain Btu/hr Occupants _ 19•3 Occupants X 245 Btuh/occ. E ul meet 6,432 Floor Area X 0.50 w/sgft c 70,976 Infiltration: 1.OG4 X 0.88 X L 362.56 X 36 = 12,275 Air Sensible CFM ELA AT TOTAL HOURLY SENSIBLE HEAT GAIN FOR ROOM 117,226 Latent Gain Btu/hr Occupants 19.9 Occupants X 155 Btuh/occ. — 2.991 Infiltration: 4,771 X 0.88 X 362.56 X 0.00344 = 5,254 Air Latent CFM ELA AW TOTAL HOURLY LATENT HEAT GAIN FOR ROOM 2,991