BRES2016-0135 Title 241r
BUILDING ENERGY ANALYSIS REPORT
PROJECT:
Hayes :Residence
61 016 Desert Rose Drive, Trilogy Country Club
La Quinta, CA 92253
Project Designer:
Andrzej W. Weber Architect
2276 Via Alba
Palm Desert, CA 92260
760.340.3002
Report Prepared by:
Wayne Seward
Bear Technologies Consulting, Inc.
7774 Calle Mejor
Carlsbad, CA 92009
760.635.2327
e -
ITY OF LA QUIP PA
CT.
ETY
BUILDING & SAFET
APPROVED
FOR C NSTRUCTION Job Number:
��
RECEIVED
1,11 � - 16Q2045.4-2
D!ATE
(p Date:
MAY 13 2016
CITY OF
5/12/2016
LAS QUINTA
COMMUNITY DEVELOPMENT
The EnergyPro computer program has been used to perform the calculations summarized in this compliance report. This program has approval and is
authorized by the California Energy Commission for use with both the Residential and Nonresidential 2013 Building Energy Efficiency Standards.
This program developed by EnergySoft, LLC — www.energysoft.com.
6.7
TABLE OF CONTENTS
Cover Page 1
Table of Contents 2
Form -CF -1 R -PRF -01-E Certificate of Compliance 3
Form RMS -1 Residential Measures Summary 13
Form MF -1 R Mandatory Measures Summary 15
HVAC System Heating and Cooling Loads Summary 19
EnergyPro 6.7 by EnergySoft Job Number: ID: 16Q2045.4-2 User Number: 5956
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD
Project Name: Hayes Residence
Calculation Description: Title 24 Analysis
Calculation Date/Time: 16:22, Thu, May 12, 2016
Input File Name: 16Q2045.4-2.xml
CF1R-PRF-01
Page 1 of 10
GENERAL INFORMATION
ENERGY USE SUMMARY
01
Project Name Hayes Residence
04
05
02
Calculation Description Title 24 Analysis
08
-
03
Project Location 61 016 Desert Rose Drive, Trilogy Country Club
Compliance Margin
04
City La Quinta
05
Standards Version Compliance 2015
06
Zip Code 92253
07
Compliance Manager Version BEMCmpMgr 2013-4 (744)
08
Climate Zone CZ15
09
Software Version EnergyPro 6.6
10
Building Type Single Family
11
Front Orientation (deg/Cardinal) 335
12
Project Scope Addition and/or Alteration
13
Number of Dwelling Units 1
14
Total Cond. Floor Area (ft2) 2937
15
Number of Zones 2
16
Slab Area (ft2) 2937
17
Number of Stories 1
18
Addition Cond. Floor Area 136
19
Natural Gas Available Yes
20
Addition Slab Area (ft) 136
21
Glazing Percentage (%) 16.3%
COMPLIANCE RESULTS
01 Building Complies with Computer Performance
02 This building DOES NOT require HERS Verification
Registration Number: Registration Date/Time: HERS Provider:
CA Building Energy Efficiency Standards - 2013 Residential Compliance Report Version - CF1R-04072016-744 Report Generated at: 2016-05-12 16:23:32
ENERGY USE SUMMARY
04
05
06
07
08
Energy Use (kTDV/ft2-yr)
Standard Design
Proposed Design
Compliance Margin
Percent Improvement
Space Heating
3.39
3.27
0.12
3.5%
Space Cooling
191.99
191.47
0.52
0.3%
IAQ Ventilation
0.00
0.00
0.00
0.0%
Water Heating
10.40
10.40
0.00
0.0%
Photovoltaic Offset
—
0.00
0.00
—
Compliance Energy Total
205.78
205.14
0.64
0.3%
Registration Number: Registration Date/Time: HERS Provider:
CA Building Energy Efficiency Standards - 2013 Residential Compliance Report Version - CF1R-04072016-744 Report Generated at: 2016-05-12 16:23:32
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD
Project Name: Hayes Residence
Calculation Description: Title 24 Analysis
Calculation Date/Time: 16:22, Thu, May 12, 2016
Input File Name: 16Q2045.4-2.xml
REQUIRED SPECIAL FEATURES
The following are features that must be installed as condition for meeting the modeled energy performance for this computer analysis.
NO SPECIAL FEATURES REQUIRED
HERS FEATURE SUMMARY
CFI R -PRF -01
Page 2 of 10
The following is a summary of the features that must be field -verified by a certified HERS Rater as a condition for meeting the modeled energy performance for this computer analysis. Additional detail is
provided in the building components tables below.
Building -level Verifications:
— None —
Cooling System Verifications:
• — None —
HVAC Distribution System Verifications:
• — None —
Domestic Hot Water System Verifications:
• —None —
ENERGY DESIGN RATING
This is the sum of the annual TDV energy consumption for energy use components included in the performance compliance approach for the Standard Design Building (Energy Budget) and the annual
TDV energy consumption for lighting and components not regulated by Title 24, Part 6 (such as domestic appliances and consumer electronics) and accounting for the annual TDV energy offset by an
on-site renewable energy system.
Reference Energy Use Energy Design Rating Margin Percent Improvement
Total Energy (kTDV/f2-yr)` 243.60 242.96 0.64 0.3%
includes calculated Appliances and Miscellaneous Energy Use (AMEU)
BUILDING - FEATURES INFORMATION
01
02
03
04
05
06
07
Project Name
Conditioned Floor Area (ft2)
Number of Dwelling
Units
Number of Bedrooms
Number of Zones
Number of Ventilation
Cooling Systems
Number of Water
Heating_ Systems
Hayes Residence
2937
1
4
2
0
1
ZONE INFORMATION
01
02
03
04
05
06
07
Zone Name
Zone Type
HVAC System Name
Zone Floor Area
(ft)
Avg. Ceiling
Height
Water Heating System 1
Water Heating System 2
MAIN HOUSE-CASITA
Conditioned
HVAC Systeml
2801
10
DHW Sys 1
PROPOSED ADDITION
Conditioned
HVAC Systeml
136
10
DHW Sys 1
Registration Number: Registration Date/Time: HERS Provider:
CA Building Energy Efficiency Standards - 2013 Residential Compliance Report Version - CF1R-04072016-744 Report Generated at: 2016-05-12 16:23:32
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD
Project Name: Hayes Residence Calculation Date/Time: 16:22, Thu, May 12, 2016
Calculation Description: Title 24 Analysis
Input File Name: 16Q2045.4-2.xml
CFI R -PRF -01
Page 3 of 10
OPAQUE SURFACES
01
02
03
04
05
06
07
08
09
10
Name
Zone
Construction
Azimuth
Orientation
Gross Area (ft2)
Window & Door
Area (ft2)
Tilt
(deg)
Status
Verified
Existing
Condition
NORTH WALL
MAIN HOUSE-CASITA
(e) ExteriorWall
0
25
60
29.8
90
Existing
No
NORTHEAST WALL
MAIN HOUSE-CASITA
(e) ExteriorWall
45
70
773.3
116.5
90
Existing
No
SOUTHEAST WALL
MAIN HOUSE-CASITA
(e) ExteriorWall
135
160
655.8
158
90
Existing
No
SOUTHWEST WALL
MAIN HOUSE-CASITA
(e) ExteriorWall
225
250
611.7
60.4
90
Existing
No
NORTHWEST WALL
MAIN HOUSE-CASITA
(e) ExteriorWall
315
340
469.5
60
90
Existing
No
IS
MAIN
HOUSE-CASITA» Garage—
(e) ISWall
592
0
Existing
No
ROOF
MAIN HOUSE-CASITA
(e) AtticRoof
2801
Existing
No
SOUTHEAST WALL 2
PROPOSED ADDITION
(n) ExteriorWall
128
153
36
18
90
New
N/A
SOUTHEAST WALL 3
PROPOSED ADDITION
(n) ExteriorWall
160
185
103.3
36
90
New
N/A
SOUTH WALL
PROPOSED ADDITION
(n) ExteriorWall
160
185
36
18
90
New
N/A
ROOF 2
PROPOSED ADDITION
(n) AtticRoof
136
New
N/A
GARAGE WALL NORTHEAST
Garage—
(e) GarageWall
45
70
22.5
0
90
Existing
No
GARAGE WALL
SOUTHWEST
— Garage—
(e) GarageWall
225
250
289.1
112
90
Existing
No
GARAGE WALL
NORTHWEST
— Garage—
(e) GarageWall
315
340
351
56
90
Existing
No
IS 3
—Garage— MAIN
HOUSE-CASITA
(e) ISWall
8
0
Existing
No
ATTIC
01
02
03
04
05
06
07
08
09
10
Radiant
Statu
Verified Existing
Name
Construction
Type
Roof Rise
Roof Reflectance
Roof Emittance
Barrier
Cool Roof
s
Condition
Attic MAIN HOUSE-CASITA
Attic RoofMAIN HOUSE-CASITA
Ventilated
3
0.1
0.85
No
No
Engti
No
Attic PROPOSED ADDITION
Attic RoofPROPOSED
Ventilated
3
0.1
0.85
No
No
New
No
ADDITION
Registration Number: Registration Date/Time: HERS Provider:
CA Building Energy Efficiency Standards - 2013 Residential Compliance Report Version - CF1R-04072016-744 Report Generated at: 2016-05-12 16:23:32
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD
Project Name: Hayes Residence I Calculation Date/Time: 16:22, Thu, May 12, 2016
Calculation Description: Title 24 Analysis
Input File Name: 16Q2045.4-2.xml
CFI R -PRF -01
Page 4 of 10
WINDOWS
01
02
03
04
05
06
07
08
09
10
11
Verified
Multiplie
Existing
Name
Surface (Orientation -Azimuth)
Width(ft)
Height (ft)
r
Area (W)
U -factor
SHGC
Exterior Shading
Status
Condition
E.
NORTH WALL (- specify -0)
-
-
1
29.8
0.40
0.35
Insect Screen (default)
Existing
No
E 2
NORTHEAST WALL (- specify
-
-
1
16.0
0.40
0.35
Insect Screen (default)
Existing
No
E. 3 '
NORTHEAST WALL (- specify
-
-
1
16.0
0.40
0.35
Insect Screen (default)
Existing
No
-45)
E. 4
NORTHEAST WALL (- specify
-
-
1
4.0
0.40
0.35
Insect Screen (default)
Existing
No
E. 5
NORTHEAST WALL (- specify
-
-
1
35.0
0.40
0.35
Insect Screen (default)
Existing
No
E. 6
NORTHEAST WALL (- specify
-
-
1
8.0
0.40
0.35
Insect Screen (default)
Existing
No
E 7
NORTHEAST WALL (- specify
-
-
1
20.0
0.40
0.35
Insect Screen (default)
Existing
No
E 8
SOUTHEAS WALL (- specify
-
-
1
40.0
0.40
0.35
Insect Screen (default)
Existing
No
-135)T
E 9
SOUTHE:AST13 ALL (- specify
-
-
1
12.0
0.40
0.35
Insect Screen (default)
Existing
No
E. 10
SOUTHEAS 1 WALL (- specify
-
-
1
14.0
0.40
0.35
Insect Screen (default)
Existing
No
E 11
SOUTHEAS 1 WALL (- specify
-
-
1
14.0
0.40
0.35
Insect Screen (default)
Existing
No
E. 12
SOUTHEAS ;WALL (- specify
-
-
1
14.0
0.40
0.35
Insect Screen (default)
Existing
No
PROPOSED 30x80 FRENCH DOO
SOUTHEAST135) (-specify
-
-
1
24.0
0.48
0.26
Insect Screen (default)
Altered
N/A
NEW 40x50 SLIDING GLASS W
SOUTHEAS 1 WALL (- specify
-
-
1
20.0
0.30
0.24
Insect Screen (default)
Altered
N/A
E. 13
SOUTHEAST WALL (- specify
-
-
1
20.0
0.40
0.35
Insect Screen (default)
Existing
No
-135)
E. 14
SOUTHWEST W; LL ( specify
-
-
1
28.2
0.40
0.35
Insect Screen (default)
Existing
No
E. 15
SOUTHWEST(- specify
-
-
1
28.2
0.40
0.35
Insect Screen (default)
Existing
No
W25WALL
Registration Number: Registration Date/Time:
CA Building Energy Efficiency Standards - 2013 Residential Compliance Report Version - CF1R-04072016-744
HERS Provider:
Report Generated at: 2016-05-12 16:23:32
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD
Project Name: Hayes Residence Calculation Date/Time: 16:22, Thu, May 12, 2016
Calculation Description: Title 24 Analysis
Input File Name: 16Q2045.4-2.xml
CF1R-PRF-01
Page 6 of 10
E. 16
SOUTHWEST WALL (- specify
—
—
1
4.0
0.40
0.35
Insect Screen (default)
Existing
No
—225)
E 17
NORTHWEST(- specify
—
—
1
13.0
0.40
0.35
Insect Screen (default)'
Existing
No
5)ALL
E. 18
NORTHWEST WALL (- specify
—
—
1
35.0
0.40
0.35
Insect Screen (default)
Existing
No
—315)
E. 19
NORTHWEST WALL (- specify
—
—
1
4.0
0.40
0.35
Insect Screen (default)
Existing
No
—315)
E. 20
NORTHWEST WALL (- specify
—
—
1
4.0
0.40
0.35
Insect Screen (default)
Existing
No
—315)
E. 21
NORTHWEST(- specify
—
—
1
4.0
0.40
0.35
Insect Screen (default)
Existing
No
5)ALL
NEW 30x60 DOUBLE HUNG WIN
SOUTHEAST WALL 2 (- specify
—
—
1
18.0
0.46
0.32
Insect Screen (default)
New
N/A
—128)
NEW 60x60 FIXED GLASS WIN
SOUTHEAST WALL 3 (- specify
—
—
1
36.0
0.34
0.24
Insect Screen (default)
New
N/A
—160)
NEW 30x60 DOUBLE HUNG WIN
SOUTH WALL (- specify —160)
—
—
1
18.0
0.46
0.32
Insect Screen (default)
New
N/A
2
DOORS
01 02 03 04 05 06
Name Side of Building Area (ft) U -factor Status Verified Existing Condition
E. 22 NORTHEAST WALL 17.5 0.50 Existing No
Registration Number: Registration Date/Time: HERS Provider:
CA Building Energy Efficiency Standards - 2013 Residential Compliance Report Version - CF1R-04072016-744 Report Generated at: 2016 -OS -12 16:23:32
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD
Project Name: Hayes Residence Calculation Date/Time: 16:22, Thu, May 12, 2016
Calculation Description: Title 24 Analysis - . Input File Name: 16Q2045.4-2.xml
CFIR-PRF-01
Page 6 of 10
OPAQUE SURFACE CONSTRUCTIONS
01
02
03
04
05
06
07
Total Cavity
Winter Design
Construction Name
Surface Type
Construction Type
Framing
R -value
U -value
Assembly Layers
• Inside Finish: Gypsum Board
• Cavity/Frame: R-11 /2x6
• Roof Deck: Wood Siding/sheathing/decking
(e) GarageRoof
Cathedral Ceilings
Wood Framed Ceiling
2x6 @ 16 in. O.C.
R11
0.083
Roofing: Light Roof (Asphalt Shingle)
• Inside Finish: Gypsum Board
• Cavity/Frame: R-11 /2x4
(e) ISWall
Interior Walls
Wood Framed Wall
2x4 @ 16 in. O.C.
R11
0.099
Other Side Finish: Gypsum Board
• Inside Finish: Gypsum Board
• Cavity/Frame: R-11 /2x4
• Exterior Finish: Wood
(e) GarageWall
Exterior Walls
Wood Framed Wall
2x4 @ 16 in. O.C.
R11
0.103
Siding/sheathing/decking
• Cavity/Frame: no insul. /2x4 Top Chrd
Attic RoofMAIN
2x4 Top Chord of Roof Truss @ 24
Roof Deck: Wood Siding/sheathing/decking
HOUSE-CASITA
Attic Roofs
Wood Framed Ceiling
in. O.C.
none
0.644
Roofing: Light Roof (Asphalt Shingle)
• Inside Finish: Gypsum Board
Ceilings (below
_
Cavity/Frame: R-9.1 /2x4
(e) AtticRoof
attic)
Wood Framed Ceiling
2x4 @ 24 in. O.C.
R 30
0.032
Over Floor Joists: R-20.9 insul.
• Inside Finish: Gypsum Board
• Cavity/Frame: R-11 /2x4
• Exterior Finish: Wood
(e) ExteriorWall
Exterior Walls
Wood Framed Wall
2x4 @ 16 in. O.C.
R11
0.103
Siding/sheathing/decking
• Cavity/Frame: no insul. /2x4 Top Chrd
Attic RoofPROPOSED
2x4 Top Chord of Roof Truss @ 24
Roof Deck: Wood Siding/sheathing/decking
ADDITION
Attic Roofs
Wood Framed Ceiling
in. O.C.
none
0.644
Roofing: Light Roof (Asphalt Shingle)
• Inside Finish: Gypsum Board
Ceilings (below
Cavity/Frame: R-9.1 /2x4
(n) AtticRoof
attic)
Wood Framed Ceiling
2x4 @ 24 in. O.C.
R 30
0.032
Over Floor Joists: R-20.9 insul.
• Inside Finish: Gypsum Board
• Cavity/Frame: R -15/2x4
• Exterior Finish: Wood
(n) ExteriorWall
Exterior Walls
Wood Framed Wall
2x4 @ 16 in. O.C.
R 15
0.089
Siding/sheathing/decking
Registration Number: Registration Datepme: HERS Provider:
CA Building Energy Efficiency Standards - 2013 Residential Compliance Report Version - CF1R-04072016-744 Report Generated at: 2016-05-12 16:23:32
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD
Project Name: Hayes Residence Calculation Date/Time: 16:22, Thu, May 12, 2016
Calculation Description: Title 24 Analysis
Input File Name: 16Q2045.4-2.xml
CF1R-PRF-01
Page 7 of 10
SLAB FLOORS
01
02
03
04
05
06
07
08
09
Name
Zone
Area (ft)
Perimeter
(ft)
Edge Insul. R -value
Carpeted
Fraction
Heated
Status
Verified
Existing
Condition
SLAB -ON -GRADE
MAIN HOUSE-CASITA
2801
254
None
0.8
No
Existing
No
SLAB -ON -GRADE 2'
PROPOSED ADDITION
136
19
None
0.8
No ..
New
No
BUILDING ENVELOPE - HERS VERIFICATION
01 02 03 04
Quality Insulation Installation (QII) Quality Installation of Spray Foam Insulation Building Envelope Air Leakage CFM50
Not Required Not Required Not Required —
WATER HEATING SYSTEMS
01
02
03
04
05
06
07
08
Name
System Type
Distribution Type
Water Heater
Number of
Heaters
Solar
Fraction
M
Status
Verified Existing
Condition
DHW Sys 1
DHW
Standard
DHW Heater 1
1
Annual
Existing
No
WATER HEATERS
01
02
03
04
05
06
07
08
Name
Heater Element Type
Tank Type
Tank Volume
(gal)
Energy Factor or
Efficiency
Input Rating
Tank Exterior
Insulation R -value
Standby Loss
(Fraction)
DHW Heater 1
Natural Gas
Small Storage
50
0.525 EF
28000-Btu/hr
0
0
WATER HEATING - HERS VERIFICATION
01
02
03
04
05
06
07
Name
Pipe Insulation
Parallel Piping
Compact Distribution
Point -of Use
Recirculation with
Manual Control
Recirculation with
Sensor Control
DHW Sys 1
n/a
n/a
n/a
n/a
n/a
n/a
Registration Number: Registration Date/Time: HERS Provider:
CA Building Energy Efficiency Standards - 2013 Residential Compliance Report Version - CF1R-04072016-744 Report Generated at: 2016-05-12 16:23:32
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD
Project Name: Hayes Residence Calculation Date/Time: 16:22, Thu, May 12, 2016
Calculation Description: Title 24 Analysis Input File Name: 16Q2045.4-2.xml
CF1 R -PRF -01
Page 8 of 10
SPACE CONDITIONING SYSTEMS
01
02
03
04
05
06
07
08
09
10
Multi -speed
Heating System
Cooling System
System Type
EER SEER
Zonally Controlled
Compressor
HERS Verification
Cooling Component 1
SplitAirCond - Split air conditioning
10
12
Distribution
Fan
Floor Area
Location
Verified Existing
Name
System Type
Name Ducted
Name Ducted
System
System
Served
Status
Condition
HVAC Systeml
Other Heating and
. Heating
Yes
Cooling
Yes
Air Distribution
HVAC Fan
2937
Existing
No
Cooling System
Component 1
Component 1
System 1
1
HVAC - HEATING SYSTEMS
01 02 03
Name Type Efficiency
Heating Component 1 CntrlFurnace - Fuel -fired central furnace 78 AFUE
HVAC - COOLING SYSTEMS
01
02
03 04
05
06
07
07
08
Efficiency
10
Multi -speed
Name
System Type
EER SEER
Zonally Controlled
Compressor
HERS Verification
Cooling Component 1
SplitAirCond - Split air conditioning
10
12
No
No
N/A
Location
system
Status
Condition
Verification
Air Distribution
Ducts located in attic
HVAC - DISTRIBUTION SYSTEMS
01
02
03
04
05
06
07
08
09
10
Insulation
Supply Duct
Return Duct
Verified Existing
HERS
Name
Type
Duct Leakage
R -value
Location
Location
Bypass Duct
Status
Condition
Verification
Air Distribution
Ducts located in attic
Existing (not
2.1
Attic
Attic
None
Existing
No
N/A
System 1
specified)
IAQ (Indoor Air Quality) FANS
01 02 03 04 05
Name IAQ CFM IAQ Fan Type IAQ Recovery Effectiveness(%) HERS Verification
SFam IAQVentRpt 0 Default 0 Not Required
Registration Number: Registration Date/Time: HERS Provider:
CA Building Energy Efficiency Standards - 2013 Residential Compliance Report Version - CF1R-04072016-744 Report Generated at: 2016-05-12 16:23:32
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD CF1R-PRF-01
Project Name: Hayes Residence Calculation Date/Time: 16:22, Thu, May 12, 2016 Page 9 of 10
Calculation Description: Title 24 Analysis Input File Name:16Q2045.4-2.xml
NOTES
) This report is based on the drawings received on 04/22/2016.
1) DO NOT USE FOR ACTUAL HEATING/COOLING DESIGN. 2) The Title 24 calculations used for this project are used for the purpose of complying with the current Title 24 code provisions
and are intended to be used in order to obtain compliance per Title 24 regulations. They are NOT intended to be used as a substitute for the heating and cooling loads required for the
structure(s) that are normally done by a mechanical engineer(s) of HVAC contractor(s) and in NO CIRCUMSTANCES are to be used in lieu of the normal calculation methods used by a
mechnical engineer(s) of HVAC contractor(s). 3) The assembly components found in this document are for modeling purposes only and may not reflect the actual conditions of the walls,
roof(s), floor(s), windows and doors of the structure. 4) Existing conditions can not be confirmed without 3rd party field verification. 5) Existing Walls, Roof(s), Floor(s), and fenestration
U -factor and SHGC are modeled as specified in Table 2-25 Standard Design for Fenestration in the 2013 Residential ACM Reference Manual.
Registration Number:
CA Building Energy Efficiency Standards - 2013 Residential Compliance
Registration Date/Time:
Report Version - CF1R-04072016-744
HERS Provider:
Report Generated at: 2016-05-12 16:23:32
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD
Project Name: Hayes Residence
Calculation Description: Title 24 Analysis
Calculation DatelTime: 16:22, Thu, May 12, 2016
Input File Name: 16Q2045.4-2.xml
CF1R-PRF-01
Page 10 of 10
DOCUMENTATION AUTHOR'S DECLARATION STATEMENT
1. 1 certify that this Certificate of Compliance documentation is accurate and complete.
Documentation Author Name: Documentation Author Signature:vea�
C" U
Wayne Seward
Company:
Signature Date:
Bear Technologies Consulting, Inc.
5/12/2016
Address:
CEA/HERS Certification Identification (If applicable):
7774 Calle Mejor
City/State/ ip:
Carlsbad, CA 92009
Phone:
760.635.2327
RESPONSIBLE PERSON'S DECLARATION STATEMENT
I certify the following under penalty of perjury, under the laws of the State of California:
1. I am eligible under Division 3 of the Business and Professions Code to accept responsibility for the building design identified on this Certificate of Compliance.
2. 1 certify that the energy features and performance specifications identified on this Certificate of Compliance conform to the requirements of Title 24, Part 1 and Part 6 of the California Code of
Regulations.
3. The building design features or system design features identified on this Certificate of Compliance are consistent with the information pr vided on other applicable compliance documents,
worksheets, calculations, plans and specifications submitted to the enforcement agency for approval with this building permit applicatio .
Responsible Designer Name:
Responsible Designer Signature:
Andrzej W. Weber
Company:
Date Signed:
� s
Andrzej W. Weber Architect
Address:
License:
Q ` '3
2276 Via Alba
-.,
City/State/Zip:
Phone:
Palm Desert, CA 92260
760.340.3002
Registration Number: Registration Date/Time:
CA Building Energy Efficiency Standards - 2013 Residential Compliance Report Version - CF1R-04072016-744
HERS Provider:
Report Generated at: 2016-05-12 16:23:32
RESIDENTIAL MEASURES SUMMARY
RMS -1
Project Name
Hayes Residence
Building Type m Single Family ❑ Addition Alone
❑ Multi Family m Existing+ Addition/Alteration
Date
5/12/2016
Project Address
61 016 Desert Rose Drive, Trilogy Country,CA
California Energy Climate Zone
Climate Zone 15
Total Cond. Floor Area
2,937
Addition
136
# of Units
1
INSULATION
Construction Type
Area
Cavity (ft) Special Features Status
Roof Wood Framed Attic
R 30 2,801
Existing
Wall Wood Framed
R11 2,146
Existing
Door Opaque Door
- no insulation 18
Existing
Demising Wood Framed
R11 592
Existing
Slab Unheated Slab -on -Grade
- no insulation 2,801 Perim = 254'
Existing
Roof Wood Framed Attic
R 30 136
New
Wall Wood Framed
R 15 103
New
Demising Wood Framed
R 13 92
New
FENESTRATION
Orientation Area ft2
I Total Area: 479 Glazing Percentage: 16.3 %
U -Fac SHGC OverhangSidefins
New/Altered Average U -Factor: 0.40
Exterior Shades Status
Front (N) 29.8
0.400
0.35 none none
Bug Screen Existing
Lek (NE) 99.0
0.400
0.35 none none
Bug Screen Existing
Rear (SE) 114.0
0.400
0.35 none none
Bug Screen Existing
Rear (SE) 24.0
0.480
0.26 none none
Bug Screen Altered
Rear (SE) 20.0
0.300
0.24 none none
Bug Screen Altered
Right (StM 60.4
0.400
0.35 none none
Bug Screen Existing
Front (NKK 60.0
0.400
0.35 none none
Bug Screen Existing
Rear (SE) 18.0
0.460
0.32 none none
Bug Screen New
Rear (S) 36.0
0.340
0.24 none none
Bug Screen New
Rear (S) 18.0
0.460
0.32 none none
Bug Screen New
HVAC SYSTEMS
Qty. Heating
Min. Eff
Cooling Min. Eff
Thermostat Status
1 Central Furnace
78% AFUE
Split Air Conditioner 12.0 SEER
Setback
Existing
HVAC DISTRIBUTION
Location Heating
Cooling Duct Location
Duct
R -Value Status
HVAC System Ducted
Ducted Attic
2.2
Existing
WATER HEATING
Qty. Type
Gallons Min. Eff Distribution Status
EnerqvPro 6.7 by EnerqySoft User Number: 5956
Run Code: 2016-05-12716:24:02
ID: 16Q2045.4-2
Pae 13 of 19
RESIDENTIAL MEASURES SUMMARY
RMS -1
Project Name
Hayes Residence
Building Type m Single Family ❑ Addition Alone
❑ Multi Family m Existing+ Addition/Alteration
Date
5/12/2016
Project Address
61 016 Desert Rose Drive, Trilogy Count
California Energy Climate Zone
CA Climate Zone 15
Total Cond. Flooddition
2,937 r Area
A 136
# of Units
1
INSULATION
Construction Type
Area
Cavity (ft)Special Features Status
Slab Unheated Slab -on -Grade no insulation 136 Perim = 19' New
FENESTRATION I Total Area: 479 Glazing Percentage- 16.3 �o New/Altered Average U -Factor: 0.40
Orientation Area ftz U -Fac SHGC Overhang Sidefins Exterior Shades Status
HVAC SYSTEMS
Qty. Heating Min. Eff
Cooling Min. Eff Thermostat Status
HVAC DISTRIBUTION
Location Heating
Duct
Cooling Duct Location R -Value Status
WATER HEATING
Qty. Type Gallons Min. Eff Distribution Status
Ener Pro 6.7 by Ener Soft User Number.- 5956
RunCode: 2016-05-12716:24:02 ID: 16Q2045.4-2
Pae 14 of 19
2013 Low -Rise Residential Mandatory Measures Summary
NOTE: Low-rise residential buildings subject to the Standards must comply with all applicable mandatory measures listed, regardless of the
compliance approach used. Exceptions may annly. Review the resnective rnde .certinn 1nr mnro infn-tinn
Building Envelope Measures:
§I 10.6(a)1:
Doors and windows between conditioned and unconditioned spaces are manufactured to limit air leakage.
§ 110.6(a)5:
Fenestration products (except field -fabricated windows) have a label listing the certified U -Factor, certified Solar Heat Gain
Coefficient SHGC , and infiltration that meets the requirements of 10-111 a .
§ 110.7:
Exterior doors and windows are weatherstripped; all joints and penetrations are caulked and sealed.
§110.8(a):
Insulation specified or installed meets Standards for Insulating Material. Indicate type and include on the CF2R.
§ 110 8(i):
The thermal emittance and aged solar reflectance values of the cool roofing material meets the requirements of § 110.8(i) when the
installation of a cool roof is specified on the CFI R.
§ 110.80):
A radiant barrier shall have an emittance of 0.05 or less when the installation of a radiant barrier is specified on the CFI R.
Minimum R-30 insulation in wood -frame ceiling; or the weighted average U -factor shall not exceed 0.031. Minimum R-19 in a
§150.0(a):
rafter roof alteration. Attic access doors shall have permanently attached insulation using adhesive or mechanical fasteners. The
attic access shall be gasketed to prevent air leakage.
§ 150.0(b):
Loose fill insulation shall conform with manufacturer's installed design labeled R -value.
§ 150.0(c):
Minimum R-13 insulation in 2x4 inch wood framing wall or have a U -factor of 0.102 or less (R -l9 in 2x6 or 0.074 maximum U -
factor).
§ 150.0(d):
Minimum R-19 insulation in raised wood -frame floor or 0.037 maximum U -factor.
150.0(g) 1:
In Climate Zones 14 and 16 a Class I1 vapor retarder shall be installed on the conditioned space side of all insulation in all exterior
walls, vented attics and unvented attics with air -permeable insulation.
§ 150.0(g)2:
In Climate Zones 1-16 with unvented crawl spaces the earth floor of the crawl space shall be covered with a Class 1 or Class II
vapor retarder.
In a building having a controlled ventilation crawl space, a Class I or Class II vapor retarder shall be placed over the earth floor of
§150.0(g)3:
the crawl space to reduce moisture entry and protect insulation from condensation, as specified in the exception to Section
150.0(d).
§150.0(1):
Slab edge insulation shall: have a water absorption rate, for the insulation material alone without facings, no greater than 0.3%;
have water vapor permeance rate is no greater than 2.0 perm/inch, be protected from physical damage and UV light deterioration;
and when installed as part of a heated slab floor meets the requirements of § 110.8
150.0
§ (q)'
Fenestration, including skylights, separating conditioned space from unconditioned space or outdoors shall have a maximum U-
factor of 0.58; or the weighted average U -factor of all fenestration shall not exceed 0.58.
Fireplaces, Decorative Gas Appliances and Gas Log Measures:
§ 150.0(e)IA:
Masonry or factory -built fireplaces have a closable metal or glass door covering the entire opening of the firebox.
§ 150.0(e)IB:
Masonry or factory -built fireplaces have a combustion outside air intake, which is at least six square inches in area and is
equipped with a readily accessible operable, and tight -fitting damper or a combustion -air control device.
§ 150.0(e)]C:
Masonry or factory -built fireplaces have a flue damper with a readily accessible control.
§ 150.0(e)2:
Continuous buming pilot lights and the use of indoor air for cooling a firebox jacket, when that indoor air is vented to the outside
of the building, are prohibited.
Space Conditioning, Water Heating and Plumbing System Measures:
§ 110.0-§ 110.3:
HVAC equipment, water heaters, showerheads, faucets and all other regulated appliances are certified to the Energy Commission.
§ 110.3(c)5:
Water heating recirculation loops serving multiple dwelling units meet the air release valve, backflow prevention, pump isolation
valve, and recirculation loop connection requirements of §I 10.3(c)5.
Continuously burning pilot lights are prohibited for natural gas: fan -type central furnaces, household cooking appliances (appli-
§ 110.5:
ances without an electrical supply voltage connection with pilot lights that consume less than 150 Btu/hr are exempt), and pool
ands a heaters.
§150.0(h)I:
Heating and/or cooling loads are calculated in accordance with ASHRAE, SMACNA or ACCA using design conditions specified
in § 150.0(h)2.
§ 150.0(h)3A:
Installed air conditioner and heat pump outdoor condensing units shall have a clearance of at least five feet from the outlet of any
dryer vent.
§150.0(i):
Heating systems are equipped with thermostats that meet the setback requirements of § 110.2(c).
§ 150.00)IA:
Storage gas water heaters with an energy factor equal to or less than the federal minimum standards shall be externally wrapped
with insulation having an installed thermal resistance of R-12 or greater.
§ 150.00)1 B:
Unfired hot water tanks, such as storage tanks and backup storage tanks for solar water -heating systems, have R-12 external
insulation or R-16 internal insulation where the internal insulation R -value is indicated on the exterior of the tank.
For domestic hot water system piping, whether buried or unburied: the first 5 feet of hot and cold water pipes from the storage
tank, all piping with a nominal diameter of 3/4 inch or larger, all piping associated with a domestic hot water recirculation system
§ I50.00)2A:
regardless of the pipe diameter, piping from the heating source to storage tank or between tanks, piping buried below grade, and
all hot water pipes from the heating source to kitchen fixtures must be insulated according to the requirements of TABLE 120.3-
A.
§ 150.00)2B:
All domestic hot water pipes that are buried below grade must be installed in a water proof and non -crushable casing or sleeve
that allows for installation, removal, and replacement of the enclosed pipe and insulation.
2013 Low -Rise Residential Mandatory Measures Summary
§ 150.00)2C:
Pipe for cooling system lines shall be insulated as specified in § I50.0Q)2A. Piping insulation for steam and hydronic heating
systems or hot waters stems with pressure > 15 psig shall meet the requirements in TABLE 120.3-A.
§ 150.00)3:
Insulation is protected from damage, including that due to sunlight, moisture, equipment maintenance, and wind.
Insulation exposed to weather shall either be rated for outdoor use or installed with a cover suitable for outdoor service. For
§ I50.00)3A:
example, protected by aluminum, sheet metal, painted canvas, or plastic cover. Cellular foam insulation protected as specified or
painted with coating that is water retardant and provides shielding from solar radiation that degrades the material.
Insulation covering chilled water piping and refrigerant suction piping located outside the conditioned space shall have a Class I
§ 150.06)3B:
or Class 11 vapor retarding facing, or the insulation shall be installed at the thickness that qualifies as a Class I or Class II vapor
retarder.
Systems using gas or propane water heaters to serve individual dwelling units shall include: a 120V electrical receptacle within 3
feet of the water heater; a Category III or IV vent, or a Type B vent with straight pipe between the outside termination and the
§ 150.0(n)1:
space where the water heater is installed; a condensate drain that is no more than 2 inches higher than the base of the installed
water heater, and allows natural draining without pump assistance; and a gas supply line with a capacity of at least 200,000
Btu/hr.
§ 150.0(n)2:
Recirculating loops serving multiple dwelling units shall meet the requirements of §I 10.3(c)5.
§150.0(n)3:
Solar water -heating systems and collectors shall be certified and rated by the Solar Rating and Certification Corporation (SRCC)
or by a testing agency approved by the Executive Director.
Ducts and Fans Measures:
All air -distribution system ducts and plenums installed are sealed and insulated to meet the requirements of CMC §601.0, §602.0,
§603.0, §604.0, §605.0 and ANSI/SMACNA-006-2006 HVAC Duct Construction Standards Metal and Flexible 3rd Edition.
Supply -air and return -air ducts and plenums are insulated to a minimum installed level of R-6.0 (or higher if required by CMC
§605.0) or enclosed entirely in directly conditioned space as confirmed through field verification and diagnostic testing
(RA3.1.4.3.8). Connections of metal ducts and inner core of flexible ducts are mechanically fastened. Openings shall be sealed
§ 150.0(m)1:
with mastic, tape, or other duct -closure system that meets the applicable requirements of UL 181, UL 181A, or UL 181 B or
aerosol sealant that meets the requirements of UL 723. If mastic or tape is used to seal openings greater than % inch, the
combination of mastic and either mesh or tape shall be used. Building cavities, support platforms for air handlers, and plenums
defined or constructed with materials other than sealed sheet metal, duct board or flexible duct shall not be used for conveying
conditioned air. Building cavities and support platforms may contain ducts. Ducts installed in cavities and support platforms
shall not be compressed to cause reductions in the cross-sectional area of the ducts.
Factory -Fabricated Duct Systems shall comply with specified requirements for duct construction, connections, and closures; joints
§150.0(m)2:
and seams of duct systems and their components shall not be sealed with cloth back rubber adhesive duct tapes unless such tape is
used in combination with mastic and draw bands.
§ 150.0(m)3-6:
Field -Fabricated Duct Systems shall comply with requirements for: pressure -sensitive tapes, mastics, sealants, and other
requirements specified for duct construction; duct insulation R -value ratings; duct insulation thickness; and duct labeling.
§ 150.0(m)7:
All fan systems that exchange air between the conditioned space and the outside of the building must have backdraft or automatic
dampers.
§ I50.0(m)8:
Gravity ventilating systems serving conditioned space have either automatic or readily accessible, manually operated dampers
except combustion inlet and outlet air openings and elevator shaft vents.
Insulation shall be protected from damage, including that due to sunlight, moisture, equipment maintenance, and wind but not
§ 150.0(m)9:
limited to the following: insulation exposed to weather shall be suitable for outdoor service. For example, protected by aluminum,
sheet metal, painted canvas, or plastic cover. Cellular foam insulation shall be protected as above or painted with a coating that is
water retardant and provides shielding from solar radiation.
§150.0(m)10:
Flexible ducts cannot have porous inner cores.
When space conditioning systems use forced air duct systems to supply conditioned air to an occupiable space, the ducts shall be
§150.0(m)1 l:
sealed and duct leakage tested, as confirmed through field verification and diagnostic testing, in accordance with Reference
Residential Appendix RA3.
Mechanical systems that supply air to an occupiable space through ductwork exceeding 10 feet in length and through a thermal
§ 150.0(m)12:
conditioning component, except evaporative coolers, shall be provided with air filter devices that meet the requirements of
§150.0(m)12.
Space conditioning systems that utilize forced air ducts to supply cooling to an occupiable space shall have a hole for the
placement of a static pressure probe (HSPP), or a permanently installed static pressure probe (PSPP) in the supply plenum. The
§150.0(m)13:
space conditioning system must also demonstrate airflow >_ 350 CFM per ton of nominal cooling capacity through the return
grilles, and an air -handling unit fan efficacy:5 0.58 W/CFM as confirmed by field verification and diagnostic testing, in
accordance with Reference Residential Appendix RA3.
Zonally controlled central forced air cooling systems shall be capable of simultaneously delivering, in every zonal control mode,
§150.0(m)15:
an airflow from the dwelling, through the air handler fan and delivered to the dwelling, of> 350 CFM per ton of nominal cooling
capacity, and operating at an air -handling unit fan efficacy of:5 0.58 W/CFM as confinned by field verification and diagnostic
testing, in accordance with Reference Residential Appendix RA3.
All dwelling units shall meet the requirements of ASHRAE Standard 62.2. Neither window operation nor continuous operation of
§ 150.0(0):
central forced air system air handlers used in central fan integrated ventilation systems are permissible methods of providing the
Whole Building Ventilation.
§ 150.0(o)IA:
Whole Building Ventilation airflow shall be confirmed through field verification and diagnostic testing, in accordance with
Reference Residential Appendix RA3.
Pool and Spa Heating Systems and Equipment Measures:
F
Any pool or spa heating system shall be certified to have: a thermal efficiency that complies with the Appliance Efficiency
§ 110.4(a):
Regulations; an on-off switch mounted outside of the heater that allows shutting off the heater without adjusting the thermostat
setting; a permanent weatherproof plate or card with operating instructions; and shall not use electric resistance heating.
2013 Low -Rise Residential Mandatory Measures Summary
§ 110.4(b)1:
Any pool or spa heating equipment shall be installed with at least 36 inches of pipe between filter and heater or dedicated suction
and return lines, or built-up connections for future solar heating.
§ 110.4(b)2:
Outdoor pools or spas that have a heat pump or gas heater shall have a cover.
§ 110.4(b)3:
Pools shall have directional inlets that adequately mix the pool water, and a time switch that will allow all pumps to be set or pro -
rammed to run only during off-peak electric demand periods.
§ 110.5:
Natural gas pool and spa heaters shall not have a continuous burning pilot light.
§150.0(p):
Residential pool systems or equipment shall meet specified pump sizing, flow rate, piping, filters, and valve requirements.
Lighting Measures:
§110.9:
All lighting control devices and systems, ballasts, and luminaires shall meet the applicable requirements of §110.9.
§150.0(k)IA:
Installed luminaires shall be classified as high -efficacy or low -efficacy for compliance with §I50.0(k) in accordance with TABLE
150.0-A or TABLE 150.0-B, as applicable.
§150.0(k)1B:
When a high efficacy and low efficacy lighting system are combined in a single luminaire, each system shall separately comply
with the applicable provisions of § 150.0(k).
The wattage and classification of permanently installed luminaires in residential kitchens shall be determined in accordance with
§ 150.0(k)I C:
§ 130.0(c). In residential kitchens, the wattage of electrical boxes finished with a blank cover or where no electrical equipment has
been installed, and where the electrical box can be used for a luminaire or a surface mounted ceiling fan, shall be calculated as 180
watts of low efficacy lighting er electrical box.
§ 150.0(k) I D:
Ballasts for fluorescent lamps rated 13 watts or greater shall be electronic and shall have an output frequency no less than 20 kHz.
Permanently installed night lights and night lights integral to installed luminaires or exhaust fans shall be rated to consume no
§150.0(k)IE:
more than 5 watts of power per luminaire or exhaust fan as determined in accordance with § I30.0(c). Night lights do not need to
be controlled by vacancy sensors.
§ 150.0(k)I F:
Lighting integral to exhaust fans (except when installed by the manufacturer in kitchen exhaust hoods) shall meet the applicable
requirements of § 150.0(k).
§ 150.0(k)2A:
High efficacy luminaires must be switched separately from low efficacy luminaires.
§ 150.0(k)2B:
Exhaust fans shall be switched separately from lighting systems.
§ 150.0(k)2C:
Luminaires shall be switched with readily accessible controls that permit the luminaires to be manually switched ON and OFF.
§ 150.0(k)2D:
Controls and equipment are installed in accordance with manufacturer's instructions.
§ 150.0(k)2E:
No control shall bypass a dimmer or vacancy sensor function if the control is installed to comply with § I50.0(k).
§ 150.0(k)2F:
Lighting controls comply with applicable requirements of § 110.9.
An Energy Management Control System (EMCS) may be used to comply with dimmer requirements if.. it functions as a dimmer
§150.0(k)2G:
according to §110.9; meets Installation Certificate requirements of §130.4; the EMCS requirements of §130.5; and all other
requirements in § 150.0(k)2.
An Energy Management Control System (EMCS) may be used to comply with vacancy sensor requirements of § 150.0(k) if: it
§ 150.0(k)2H:
functions as a vacancy sensor according to § 110.9; meets Installation Certificate requirements of § 130.4; the EMCS requirements
of § 130.5; and all other requirements in § 150.0(k)2.
§ 150.0(k)21:
A multiscene programmable controller may be used to comply with dimmer requirements of this section if it provides the
functionality of a dimmer according to §110.9, and complies with all other applicable requirements in §150.0(k)2.
§ 150.0(k)3A:
A minimum of 50 percent of the total rated wattage of permanently installed lighting in kitchens shall be high efficacy.
-
Kitchen lighting includes all permanently installed lighting in the kitchen except internal lighting in cabinets that illuminate only
§ 150.0(k)3B:
the inside of the cabinets. Lighting in areas adjacent to the kitchen, including but not limited to dining and nook areas, are
considered kitchen lighting if they are not separately switched from kitchen lighting.
§150.0(k)4:
Permanently installed lighting that is internal to cabinets shall use no more than 20 watts of power per linear foot of illuminated
cabinet.
§ 150.0(k)5:
A minimum of one high efficacy luminaire shall be installed in each bathroom; and all other -lighting installed in each bathroom
shall be high efficacy or controlled by vacancy sensors.
§ 150.0(k)6:
Lighting installed in attached and detached garages, laundry rooms, and utility rooms shall be high efficacy luminaires and
controlled by vacancy sensors.
§150.0(k)7:
Lighting installed in rooms or areas other than in kitchens, bathrooms, garages, laundry rooms, and utility rooms shall be high
efficacy, or shall be controlled by either dimmers or vacancy sensors.
Luminaires recessed into ceilings shall: be listed for zero clearance insulation contact (IC) by Underwriters Laboratories or other
nationally recognized testing/rating laboratory; have a label that certifies that the luminaire is airtight with air leakage less than 2.0
CFM at 75 Pascals when tested in accordance with ASTM E283; be sealed with a gasket or caulk between the luminaire housing
§150.0(k)8:
and ceiling, and shall have all air leak paths between conditioned and unconditioned spaces sealed with a gasket or caulk; and
allow ballast maintenance and replacement without requiring cutting holes in the ceiling.
For recessed compact fluorescent luminaries with ballasts to qualify as high efficacy for compliance with §150.0(k), the ballasts
shall be certified to the Energy Commission to comply with the applicable requirements in § 110.9.
For single-family residential buildings, outdoor lighting permanently mounted to a residential building or other buildings on the
same lot shall be high efficacy, or may be low efficacy if it meets all of the following requirements:
i. Controlled by a manual ON and OFF switch that does not override to ON the automatic actions of Items ii or iii below; and
§ 150.0(k)9A:
ii. Controlled by a motion sensor not having an override or bypass switch that disables the motion sensor, or controlled by a
motion sensor having a temporary override switch which temporarily bypasses the motion sensing function and automatically
reactivates the motion sensor within 6 hours; and
iii. Controlled by one of the following methods:
2013 Low -Rise Residential Mandatory Measures Summary
a. Photocontrol not having an override or bypass switch that disables the photocontrol; or
b. Astronomical time clock not having an override or bypass switch that disables the astronomical time clock, and which is
programmed to automatically turn the outdoor lighting OFF during daylight hours; or
c. Energy management control system which meets all of the following requirements: At a minimum provides the functionality of
an astronomical time clock in accordance with § 110.9; meets the Installation Certification requirements in § 130.4; meets the
requirements for an EMCS in §130.5; does not have an override or bypass switch that allows the luminaire to be always ON; and,
is programmed to automatically turn the outdoor lighting OFF during daylight hours.
For low-rise multifamily residential buildings, outdoor lighting for private patios, entrances, balconies, and porches; and outdoor
lighting for residential parking lots and residential carports with less than eight vehicles per site shall comply with one of the
§ 150.0(k)9B:
following requirements:
i. Shall comply with §150.0(k)9A; or
ii. Shall comply with the applicable requirements in §110.9, §130.0, §130.2, §130.4, §140.7 and §141.0.
§ 150.0(k)9C:
For low-rise residential buildings with four or more dwelling units, outdoor lighting not regulated by § 150.0(k)9B or 150.0(k)9D
shall comply with the applicable requirements in 110.9, 130.0, 130.21 130.4, 140.7 and 141.0.
§ 150.0(k)9D:
Outdoor lighting for residential parking lots and residential carports with a total of eight or more vehicles per site shall comply
with the applicable requirements in § 110.9, § 130.0, § 130.2, § 130.4, § 140.7 and § 141.0.
§ 150.0(k)10:
Internally illuminated address signs shall comply with §140.8; or shall consume no more than 5 watts of power as determined
according to §130.0(c).
§150.0(k)11:
Lighting for residential parking garages for eight or more vehicles shall comply with the applicable requirements for
nonresidential garages in § 110.9, § 130.0, §130. 1, § 130.4, § 140.6, and ' 141.0.
In a low-rise multifamily residential building where the total interior common area in a single building equals 20 percent or less of
§ 150.0(k)12A:
the floor area, permanently installed lighting for the interior common areas in that building shall be high efficacy luminaires or
controlled by an occupant sensor.
In a low-rise multifamily residential building where the total interior common area in a single building equals more than 20
percent of the floor area, permanently installed lighting in that building shall:
§150.0(k)12B:
i. Comply with the applicable requirements in §110.9, §130.0, §130.1, §140.6 and §141.0; and
ii. Lighting installed in corridors and stairwells shall be controlled by occupant sensors that reduce the lighting power in each
space by at least 50 percent. The occupant sensors shall be capable of turning the light fully On and Off from all designed paths of
ingress and egress.
Solar Ready Buildings:
Single family residences located in subdivisions with ten or more single family residences and where the application for a
§I 10.10(a)1:
tentative subdivision map for the residences has been deemed complete, by the enforcement agency, on or after January 1, 2014,
shall comply with the requirements of § 110.10(6) through § l 10.10 e .
§I10.10(a)2:
Low-rise multi -family buildings shall comply with the requirements of §I 10.10(b) through §I 10.10(d).
The solar zone shall have a minimum total area as described below. The solar zone shall comply with access, pathway, smoke
ventilation, and spacing requirements as specified in Title 24, Part 9 or other Parts of Title 24 or in any requirements adopted by a
local jurisdiction. The solar zone total area shall be comprised of areas that have no dimension less than 5 feet and are no less than
80 square feet each for buildings with roof areas less than or equal to 10,000 square feet or no less than 160 square feet each for
§ 110.10(b)1:
buildings with roof areas greater than 10,000 square feet.
For single family residences the solar zone shall be located on the roof or overhang of the building and have a total area no less
than 250 square feet. For low-rise multi -family buildings the solar zone shall be located on the roof or overhang of the building or
on the roof or overhang of another structure located within 250 feet of the building or on covered parking installed with the
building project and have a total area no less than 15 percent of the total roof area of the building excluding any skylight area.
§ 110.10(b)2:
All sections of the solar zone located on steep -sloped roofs shall be oriented between 110 degrees and 270 degrees of true north.
§ 110.10(b)3A:
No obstructions, including but not limited to, vents, chimneys, architectural features, and roof mounted equipment, shall be
located in the solar zone.
Any obstruction, located on the roof or any other part of the building that projects above a solar zone shall be located at least twice
§ 110.10(b)3B:
the distance, measured in the horizontal plane, of the height difference between the highest point of the obstruction and the
horizontal projection of the nearest point of the solar zone, measured in the vertical plane.
§ 110.10(b)4:
For areas of the roof designated as solar zone, the structural design loads for roof dead load and roof live load shall be clearly
indicated on the construction documents.
The construction documents shall indicate: a location for inverters and metering equipment and a pathway for routing of conduit
§ 110.10(c):
from the solar zone to the point of interconnection with the electrical service (for single family residences the point of
interconnection will be the main service panel); a pathway for routing of plumbing from the solar zone to the water -heating
system.
§110.10(d):
A copy of the construction documents or a comparable document indicating the information from §110.10(b) through §110.10(c)
shall be provided to the occupant.
§ 110.10(e) l :
The main electrical service panel shall have a minimum busbar rating of 200 amps.
The main electrical service panel shall have a reserved space to allow for the installation of a double pole circuit breaker for a
§ 110.10(e)2:
future solar electric installation. The reserved space shall be: positioned at the opposite (load) end from the input feeder location or
main circuit location, and permanently marked as "For Future Solar Electric'.
HVAC SYSTEM HEATING AND COOLING LOADS SUMMARY
Project Name
Date
Hayes Residence
5/12/2016
System Name
Floor Area
HVAC System
2,937
ENGINEERING CHECKS
SYSTEM LOAD
Number of Systems
1
COIL
CFM
Total Room Loads 1,988
Return Vented Lighting
Return Air Ducts
Return Fan
Ventilation 0
Supply Fan
Supply Air Ducts
TOTAL SYSTEM LOAD
COOLING
PEAK COIL HTG.
PEAK
Heating System
Sensible
Latent CFM
Sensible
Out ut erS stem 60,000
38,091
3,521 982
36,560
Total Output Btuh 60,000
0
Output Btuhls ft 20.4
4,796
3,798
Cooling System
0
0
Output perSystem 36,000
0
0 0
0
Total Output Btuh 36,000
0
3,521 1
0
Total Output Tons 3.0
4,796
3,798
Total Output Btuh/s ft 12.3
Total Output s ft/Ton 979.0
47,683
44,157
Air System
CFM perSystem
1,050
HVAC EQUIPMENT SELECTION
Airflow cfm
1,050
(e) FAU - A/C 27,619
3,273
60,000
Airflow cfmis ft
0.36
Airflow cfm/Ton 350.0
Outside Air %°
°
Total Adjusted System Output 27,619
(Adjusted for Peak Design conditions)
TIME OF SYSTEM PEAK
3,273 60,000
Aug 3 PM Jan 1 AM
Outside Air cfm/s ft 0.00
Note: values above given at ARI conditions
HEATING SYSTEM PSYCHROMETRICS
Airstream Temperatures at Time of Heating Peak
26 OF
66 OF 105 °F 105 OF
10
Outside Air
lop loll
=11 0 r'
Pi ► _, ,„ ,�
0 cfm
Heating Coil Supply Fan
1,050 cfm
103 °F
ROOM
66 OF
68 of
COOLING SYSTEM PSYCHROMETRICS Airstream Temperatures at Time of Cooling Peak
112/78°F
77/63°F 55/54°F 55/54°F
• ��
Outside Air
0 cfm
Cooling Coil Supply Fan
57 ! 55 OF
1,050 cfm
48.7%
ROOM
77163 OF
I
75 162 OF
4 No, 1
4 --U -1
1
EnergyPro 6.7 by EnergySoff
User Number: 5956 Run Code: 2016-05-12T16:24:02 /D: 16Q2045.4-2 Page 19 of 19