05-4855 (RC) Title 241 '
J
TITLE 24 REPORT
Title 24 Report for:
Shops 3A- Famous Footwear
The Pavillion at La Quinta
La Quinta, Ca
Project Designer:
Smith Consulting Architects
12220 EI Camino Real, Suite 200
San Diego, Ca 92130
(858)-793-4777
Report Prepared By:
Krishna C. Kumar P.E.
Guthrie and Associates Inc.
370 S. Crenshaw Blvd., Suite E-104
Torrance, CA 90503
(310) 787-7825
Job Number:
040310-3AF
Date:
9/15/2005
CITY OF LA QUINTA
BUILDING & SAFETY DEPT.
APPROVED
F6R CONSTRUCTION
11A1E� ` & W-la-
MMhL
TheEnergyPro computer program has been used to perform the calculations summarized in this compliance report. This program has approval and is
:authorized by the California Energy Commission for use with both the Residential and Nonresidential 2005 Building Energy Efficiency Standards.
This program developed by EnergySoft, LLC - www.energysoft.com.
':� EnergyPro 4.0 by EnergySoft Job Number. 040310-3AF User Number: 1645
u
L
PERFORMANCE CERTIFICATE OF COMPLIANCE Part 1 of 3 PERF -1
PROJECT NAME
This Certificate of Compliance lists the building features and performance specifications needed to comply with Title 24, Parts 1 and 6 of the
DATE
11 Shops 3A- Famous Footwear
BUILDING CONDITIONED FLOOR AREA
6,500Sq.Ft.
9/15/2005
PROJECT ADDRESS
NONRESIDENTIAL HIGH RISE RESIDENTIAL HOTEL/MOTEL GUEST ROOM
PHASE OF CONSTRUCTION ®
The Paviliuon at La Quinta La Quinta
permit application. The proposed building as designed meets the energy efficiency requirements contained in sections 110, 116,
through 118, and 140, 142, 143 or 149 of Title 24, Part 6.
PRINCIPAL DESIGNER - ENVELOPE
TELEPHONE
Building Permit #
Smith Consulting Architects
(858)-793-4777
5537.2 or 6737.3 to sign this document as the person responsible for its preparation; and that I am a licensed
DOCUMENTATION AUTHOR
Guthrie and Associates Inc.
TELEPHONE
(310) 787-7825
Checked by/Date
Code Sections 5537, 5538, and 6737.1. (These sections of the Business and Professions Code are printed in
full in the Nonresidential Manual.)
Enforcement Agency Use
GENERAL INFORMATION
This Certificate of Compliance lists the building features and performance specifications needed to comply with Title 24, Parts 1 and 6 of the
DATE OF PLANS
The documentation preparer hereby certifies that the documentatio is accurate and complete.
BUILDING CONDITIONED FLOOR AREA
6,500Sq.Ft.
CLIMATE ZONE
15
BUILDING TYPE ®
NONRESIDENTIAL HIGH RISE RESIDENTIAL HOTEL/MOTEL GUEST ROOM
PHASE OF CONSTRUCTION ®
NEW CONSTRUCTION ❑ ADDITION [:] ALTERATION EXISTING + ADDITION
STATEMENT OF COMPLIANCE
This Certificate of Compliance lists the building features and performance specifications needed to comply with Title 24, Parts 1 and 6 of the
California Code of Regulations. This certificate applies only to a Building using the performance compliance approach.
The documentation preparer hereby certifies that the documentatio is accurate and complete.
DOCUMENTATION AUTHOR
SI U p
Krishna C. Kumar P.E.
-��
The Principal Designer hereby certifys that the proposed building design repr Is set of construction documents is
consistent with the other compliance forms and worksheets, with the specifications, a with any other calculations submitted with this
permit application. The proposed building as designed meets the energy efficiency requirements contained in sections 110, 116,
through 118, and 140, 142, 143 or 149 of Title 24, Part 6.
ENV LTG. MECH.
1. 1 hereby affirm that I am eligible under the provisions of Division 3 of the Business and Professions Code to
n this document as the person responsible for its preparation; and that I am licensed in the State of
California as a civil engineer, mechanical engineer, or I am a licensed architect.
❑ ❑ F-1 2. 1 affirm that I am eligible under the provisions of Division 3 of the Business and Professions Code Section
5537.2 or 6737.3 to sign this document as the person responsible for its preparation; and that I am a licensed
contractor performing this work.
❑ F-1 F1 3. 1 affirm that I am eligible under Division 3 of the Business and Professions Code to sign this document
because it pertains to a structure or type of work described as exempt pusuant to Business and Professions
Code Sections 5537, 5538, and 6737.1. (These sections of the Business and Professions Code are printed in
full in the Nonresidential Manual.)
ENVELOPE COMPLIANCE
Indicate location on plans of Note Block for Mandatory Measures
. to .–
ENV -1
Required Forms
PRINCIPAL ENVELOPE DESIGNER - NAME
SIGNATURE
LIC. NO.
DATE
Smith Consulting Architects
LIGHTING COMPLIANCE
Indicate location on plans of Note Block for Mandatory Measures
Lighting Compliance Not In The Scope Of
Required Forms
PRINCIPAL LIGHTING DESIGNER - NAME
SIGNATURE
LIC. NO.
DATE
MECHANICAL COMPLIANCE
Indicate location on plans of Note Block for Mandatory Measures
—3
MEC 1 MECH-2 MECH-3
Required Forms
PRINCIPAL MECHANICAL DESIGNER - NAMENATURE /�
Guthrie
LIC. N0.
0
DATE
ot
and Associates Inc. ,
22( 7%
EnergyPro 4.0 by EnergySoft User Number: 1645 Job Number: 040310-3AF Page:3 of 16
PERFORMANCE CERTIFICATE OF COMPLIANCE Part 2 of 3 PER
PROJECT NAME DATE
Shops 3A- Famous Footwear 9/15/2005
ANNUAL TDV ENERGY USE SUMMARY kBtu/s ft- r
Standard
ENERGY COMPONENT Design
Space Heating 0.08
Space Cooling 363.39
Indoor Fans 85.34
Heat Rejection 0.00
Pumps & Misc. 0.00
Domestic Hot Water 69.23
Lighting 187.30
Receptacle 87.43
Process 0.00
TOTALS: 792.76
Percent better than Standard:
Proposed Compliance
Design Margin
0.00 0.07
361.85 1.53°°""'B
87.31 -1.96
0.00 0.00
0.00 0.00
67.11 2.13
187.30 0.00
87.43 0.00
0.00 0.00
790.99 1.77
0.2% ( 0.2% excluding
° iro 0 PLp2wd
-111101111
0 30, 60 90 j120 150 180 210 240 270300 330360
Mweafl•n
process)
BUILDING COMPLIES
GENERAL INFORMATION
Building Orientation
Number of Stories
Number of Systems
Number of Zones
South 180 deg
Conditioned Floor Area
Unconditioned Floor Area
Conditioned Footprint Area
Fuel Type
6,500
sqft.
sqft.
sqft.
1
0
3
6,500
21
Natural Gas
Orientation
Front Elevation South
Left Elevation (West)
Rear Elevation North
Right Elevation I (East)
Total
Roof
Gross Area
sqft.
sqft.
sqft.
sqft.
sqft.
Glazing Area
Glazing
sqft.
sqft.
sqft.
sgft.
sqft.
sqft.
Ratio
1,170
410
35.0%
0
0
0.0%
1,152
0
0.0%
0
0.0%
t72,3212sqft.
410
17.7%
=iiR
E:�
0.0%
Standard Proposed
Lighting Power Density 1.700 W/sqft. 1.700 W/sqft.
Prescriptive Env. Heat Loss 1,300 Btu/h 1,358 Btu/h
Prescriptive Env. Heat Gain 102,107 Btum-F 123,394 Btuth-F
Remarks:
Run Initiation Time: 09/15/0510:22:48 Run Code: 1126804968
EnergyPro 4.0 by EnergySoft User Number: 1645 Job Number: 040310-3AF PageA of 16
PERFORMANCE CERTIFICATE OF COMPLIANCE Part 3 of 3 PERF -1
11 PROJECT NAME
Shops 3A- Famous Footwear
DATE
9/15/2005
ZONE INFORMATION
System Name Zone Name Occupancy Type
Floor
(Sgft)
Inst.
(W/D
f)1
Ctrl.
Credits
(W/sf)2
Allowed LPD
I Proc.
Loads
(Wlsf)
Area Tailored
/s 3 /s 4
Sales/Stock Room -8.5T A/C Sales/Stock Room Retail Sales, Wholesale
2,000
'1.70
Sales/Tits-(2)7.5T A/C Sales/Tlts Retail Sales, Wholesale
4,500
-1.70
Notes: 1. See LTG -2-C 2. See LTG -4-C 3. See LTG -5-C
(items marked with asterisk, see LTG -2 -C by others) (by others)
4. See LTG -6-C
Items above require special documentation
EXCEPTIONAL CONDITIONS COMPLIANCE CHECKLIST
nn wL141 rrnivrceanenc agency 5"01.110 pay special attention to the Mems Specitlea in this checklist. These items require special written justification
and documentation, and special verification to be used with the performance approach. The local enforcement agency determines the adequacy of
the justification, and may reject a building or design that otherwise complies based on the adequacy of the special justification and documentation
submitted.
The HVAC System "Sales/Stock Room -8.5T A/C' includes Demand Control Ventilation per Standards Section 121.
The HVAC System "Sales/Tlts-(2)7.5T A/C' includes Demand Control Ventilation per Standards Section 121.
I ne exceptional reatures ustea in tms performance approach application have specifically been reviewed. Adequate written justification and
documentation for their use have been provided by the applicant.
or
EnergyPro 4.0 by EnergySoft User Number: 1645 Job Number. 040310-3AF Page:5 of 16
CERTIFICATE OF COMPLIANCE ENV -
PROJECT NAME
Shops 3A- Famous Footwear
OPAQUE SURFACES
DATE
9/15/2005
#
Surface
T e
Area
U -Fac.
Insulation
Cay. Cont.
Act.
Azm.
Tilt
Cond' Joint
Status
Appendix
IV Reference
Location / Comments
1
Wall
272
0.285
None
R-7.2
180
90
New
12-A8
Sales/Stock Room
2
Wall
666
0.285
None
R-7.2
0
90
New
12-A8
Sales/Stock Room
3
Roof
2,000
0.051
-
180
0
New
02-A5
Sales/Stock Room
4
Wall
488
0.285
None
R-7.2
180
90
New
12-A8
Sales/Tlts
5
Wall
465
0.285
None
R-7.21
0
90
New
12-A8
Sales/Tits
6
Door
21
1.4501
None
R-0.0
0
90
New
28-A1
Sales/Tlts
7
Roof
4,500
0.051
R-19
R-0.0
180
0
New
02-A5
Sales/Tlts
' N. E. A. R (New, Existing, Altered, Removed)
FENESTRATION SURFACES
❑More than or equal to 10,000 sq.ft. of site -built fenestration area must include a label certificate either issued by NFRC or provide a CEC Default Label Certificate using the default U -factors
from Standards Table 116-A and B. Certificate shall be filed in the contractors Droied office dudna construction and in ma huildinn mnnanare nffim affar — f iMi—
Act.
# Tvpe Area U -Fac? SHGC2 Am.
Cond.
Stat. Glazing Type
Location/
Comments
1 Window Front South 340 1.190 NFRC 0.80 116-B 180
New Single Clear Glass
Sales/Stock Room
2 Window Front South 70 1.190 NFRC 0.80 116-B 180
New Single Clear Glass
Salesrrlts
2 None
0.76 10.0 7.0
11.0 0.1 11.0 11.0
(1) U -tactor Type: 116-A Default Table from Standards, Table NI -1 Default Table from the ACM Manual Appendix, NFRC Labeled value.
(2) SHGC Type: 116-B Default Table from Standards, COG Center of Glass, NFRC Labeled Value
EXTERIOR SHADING
# Exterior Shade Type
Window
HGC Hgt. Wd.
Overhang Left Fin Right Fin
Len. H t. LExt.RExt. Dist. Len. H t. Dist. Len. H t.
1 None
0.76 10.0 34.0
11.0 0.1 11.0 11.0
2 None
0.76 10.0 7.0
11.0 0.1 11.0 11.0
MINIMUM SKYLIGHT AREA FOR LARGE ENCLOSED SPACES
The proposed building contains an enclosed space with floor area greater than 25,000 sq.ft, a ceiling height greater than 16 feet and a LPD for general lighting of at least
0.5 W/sq.ft. If this box Is checked, ENV44 must be filled out when submitting under the Prescriptive Compliance Approach.
EnergyPro 4.0 by EnergySoft User Number: 1645 Job Number: 040310-3AF Page: 6 of 16
r�
CERTIFICATE OF COMPLIANCE MECH-1-C
(PROJECT NAME DATE
Shops 3A- Famous Footwear 9/15/2005
esigner:
This form is to be used by the designer and attached to the plans. Listed below are all the acceptance tests for mechanical systems. The designer is
required to check the boxes by all acceptance tests that apply and list all equipment that requires an acceptance test. If all equipment of a certain type
requires a test, list the equipment description and the number of systems to be tested in parentheses. The NJ number designates the Section in the
Appendix of the Nonresidential ACM Manual that describes the test. Also indicate the person responsible for performing the tests (i.e. the installing
contractor, design professional or an agent selected by the owner). Since this form will be part of the plans, completion of this section will allow the
responsible party to budget for the scope of work appropriately.
Building Departments:
SYSTEM ACCEPTANCE. Before an occupancy permit is granted for a newly constructed building or space, or a new space -conditioning system serving a
building or space is operated for normal use, all control devices serving the building or space shall be certified as meeting the Acceptance Requirements for
Code Compliance.
In addition a Certificate of Acceptance, MECH-I-A Form shall be submitted to the building department that certifies plans, specifications, installation
certificates, and operating and maintenance information meet the reauiements of Sertinn 1 n-1 nsrhl nnri Titip 9d Pnrt a
STATEMENT OF COMPLIANCE
❑ MECH-2-A: Ventilation System Acceptance Document
-Variable Air Volume Systems Outdoor Air Acceptance
-Constant Air Volume Systems Outdoor Air Acceptance
Equipment requiring acceptance testing
❑ MECH-3-A: Packaged HVAC Systems Acceptance Document
Equipment requiring acceptance testing
❑ MECH-4-A: Air Distribution Acceptance Document
Equipment requiring acceptance testing
❑ MECH-5-A: Air -Side Economizer Acceptance Document
Equipment requiring acceptance testing
❑ MECH-6-A: Demand Control Ventilation Acceptance Document
Equipment requiring acceptance testing
❑ MECH-7-A: Supply Fan Variable Flow Control Acceptance Document
Equipment requiring acceptance testing
❑ MECH-8-A:-Hydronic System Control Acceptance Document
-Variable Flow Controls
-Automatic Isolation Con-trols
-Water-loop Heat Pump Controls
-Variable Frequency Controls
Equipment requiring acceptance testing
EnergyPro 4.0 by EnergySoft User Number: 1645 Job Number: 040310-3AF Page:7 of 16
AIR SYSTEM REQUIREMENTS Part 1 of 2 MECH-2-C
ECT NAME
Shops 3A- Famous Footwear
ITEM OR SYSTEM TAG(S)
Number of Systems
T-24
MANDATORY MEASURES Section
Heating Equipment Efficiency
Cooling Equipment Efficiency
Heat Pump Thermostat
Furnace Controls
Natural Ventilation
Minimum Ventilation
VAV Minimum Position Control
Demand Control Ventilation
Time Control
Setback and Setup Control
Outdoor Damper Control
Isolation Zones
Pipe Insulation
•Duct Insulation
PRESCRIPTIVE MEASURES
Calculated Heating Capacity x 1.43 2
Proposed Heating Capacity 2
Calculated Sensible Cooling Capacity x 1.212
Proposed Sensible Cooling Capacity 2
Fan Control
DP Sensor Location
Supply Pressure Reset (DDC only)
Simultaneous Heat/Cool
Economizer
Heating Air Supply Reset
Cooling Air Supply Reset
Duct Sealing for Prescriptive Compliance
DATE
9/15/2005
AIR SYSTEMS, Central or Single Zone
Sales/Stock Room -8.5T A/C Saleslrlts-(2)7.5T A/C
1 1 2
Reference on Plans or Specification 1
112(a)
80% AFUE
83% AFUE
112(a)
10.8 EER
11.0 EER
112(b)
n/a
n/a
112(c), 115(a)
n/a
n/a
121(b)
No
No
121(b)
519 cfm
1125 cfm
121 c
No
No
121(c)
Yes
Yes
121(c), 122(e)
Programmable Switch
Programmable Switch
122(e)
Heating & Cooling Required
Heating & Cooling Required
122
Gravity
Gravity
122(g)
n/a
n/a
123
124
R-4.2
R-4.2
144 a & b
n/a
n/a
144 a & b
100,000 btuh
200,000 btuh
144 a & b
n/a
n/a
144 a & b
81,569 btuh
139,509 btuh
144 c
Constant Volume
Constant Volume
144 (c)
144 c
Yes
Yes
144 d
No
No
144 a
No Economizer
Fixed Tem (Integrated)
144
Constant Temp
Constant Tem
144(f)
Constant Temp
Constant Temp
144 (k
No
No
1: For each central and single zone air systems (or group of similar units) fill in the reference to sheet number and/or specification section and paragraph number where the
required features are documented. If a requirement is not applicable, put "N/A" in the column.
2: Not required for hydronic heating and cooling. Either enter a value here or put in reference of plans and specficatons per footnote 1.
3: Enter Yes if System is: Constant Volume, Single Zone; Serves < 5,000 sqft; Has > 25% duct in unconditioned space. Duct sealing is required for Prescriptive Compliance,
see PERF -1 for performance method duct sealing requirements.
EnergyPro 4.0 by EnergySoft User Number: 1645 Job Number: 040310-3AF Pape:8 of 16
WATER SIDE SYSTEM REQUIREMENTS Part 2 of 2 MECH-2-C
PROJECT NAME
3A- Famous Footwear
2 WATER SIDE SYSTEMS: Chi
ITEM OR SYSTEM TAG(S)
Number of Systems
DATE
9/15/2005
T-24
MANDATORY MEASURES Section Reference on Plans or Specification
Equipment Efficiency 112(a)
Pipe Insulation 123
PRESCRIPTIVE MEASURES
Calculated Capacity
Proposed Capacity
Tower Fan Controls
Tower Flow Controls
Variable Flow System Design
Chiller and Boiler Isolation
CHW and HHW Reset Controls
WLHP Isolation Valves
VSD on CHW, CW & WLHP Pumps > 5
HP
DP Sensor Location
•1: For each chiller, cooling tower, boiler, and hydronic loop (or groups of similar equipment) fill in the reference to sheet number and/or specification section and paragraph
number where the required features are documented. If a requirement is not applicable, put "N/A" in the column.
2: Water side systems include wet side system using other liquids such as glycol or brine.
Service Hot Water, Pool Heating
ITEM OR SYSTEM TAG(S) DHW Heater
Number of Systems 2
]E
MANDATORY MEASURES Reference on Plans or Specification
Water Heater Certification
113 (a)
Water Heater Efficiency
113 b
Service Water Heating Installation
113 (c)
Pool and Spa Efficiency and Control
114 a
Pool and Spa Installation
114 b
Pool Heater - No Pilot Light
115 (c)
Spa Heater - No Pilot Light
115 d
Chronomite Instant WH
99%
n/a
n/a
1: For each water heater, pool heat and domestic water loop (or groups of similar equipment) fill in the reference to sheet number and/or specification section and
paragraph number where the required features are documented. If a requirement is not applicable, put "N/A" ins the column.
Run Initiation Time: 09/15/05 10:22:48 Run Code: 1126804968
EnergyPro 4.0 by EnergySoft User Number: 1645 Job Number: 040310-3AF Page:9 of 16
Om
LO
O
O
N
U')
r
O)
U-
a
49
Z
Transfer Air
`o
0
Design Min. Ai
Q
Setpoint
°
�
d
o
L c
Max of
X.0
Columns H, J,
2
L 6
K or 300 CFM
a
l z
2
B x 0.4
h
E
X 0
a
Y
CFM/sq. ft
g
m
.0
i g
30% of Design
_i
Zone Supply
CFM
g
�?
Design
°'
°'
N
N
m
N
°
a
—
Vent. Air
`"
'"
Ea
CFM
m
o
g
C?
o
REQ'D V.A
o
o Nto
N
=
v -i
E x
o
=
Max of
LO
to
E
(D or G)
N
Min CFM
m
m
o
a
E$
E
vs
C9
by Occupant
a
0
E.
E
z=
m
(E x F)
o
g
v
CFM
Z
IL
LL
per
Person
=
m
a
? o E
$ =
U
m��
E
s
w
Number of
$
o
o
O
People
m m
c-
o-°
E
Min CFM
o
LO
`1'
3
$
p
by Area
m
S�
N
ti
(BxC)
o
o4
Q
CFM
N
N
0
E
ro =
ar
m
0
per
O
O
o
E
c s
E
!V
Square Foot
a
m g
$ a
_
z
c
a7Condi.tion
o
;=
9
o m>
�.
N
t
0•Q>
VI
m
m
°
OO°�=
o
X
O S
= r d
O 0 m
_
m
m
LL
p
3
E-
La
m
L)
'a
C
= vm
O
m
m
w=
¢
21
H
Z
W
`o
c
,E
G"
c
io n
c
W
N
V
a
o y
o
6
-_
E
=
N a
m
W
>
Q
N
E
m
u°
�_
E v
O
O
c
o
.�
ziB
O
c>>
0
IX
n
= v
a
"c1O.
c
o<
a _.
--a
o
Z=
N
o
0
y
- umi
m�1o��
= y-
c 'Z
m
m
d
a
o
21
_
D5
t
w
IUm
-6
N
Z-
W
Y
f Z
a
49
MECHANICAL EQUIPMENT DETAILS
Part 1 of 2 MECH-5-C
PROJECT NAME
Shops 3A- Famous Footwear
th ft
DATE 9/15/2005
HILLER AND TOWER SUMMARY
Control
#
HP
Type
In Plenum
Outside
Buried
Efficiency
Tons
PUMPS
Equipment Name
Equipment Type
Qty.
Tot.
Qty
GPM
I BHP
Motor
Eff.
Drive
Eff.
Pump
Control
CENTRAL SYSTEM RATINGS
HEATING
COOLING
System Name
System Type
Qty
Output-
Aux.
kW
Eff.
Output
Efficiencv
Condition
Status
Economizer Type
Carrier 48HJD009- A/C
Packaged DX
1
100,000
QHW / BOILER SUMMARY
80%AFUE
Energy Standby ITANK INSUL.
Rated Vol. Condition Factor Loss or Ext.
System Name System Type Distribution Type Qty Input I (Gals.) Status or RE Pilot I R -Val.
Chronomite Instant WH Instant Elec Parallel Piping 2 10,329 0 New 0.96 n/a n/a
System Name Fan Type
Carrier 48HJD009- A/C
Constant Volume
Carrier 48HJDF008- A/C
Constant Volume
Motor Location
Hot Water P mp
Hot Water Piping Long
th ft
Drive
Eff.
CFM
Control
#
HP
Type
In Plenum
Outside
Buried
Add 1/2"
Insulation
none
Draw -Through
3,000
1.30
82.5%
97.0%
none
CENTRAL SYSTEM RATINGS
HEATING
COOLING
System Name
System Type
Qty
Output-
Aux.
kW
Eff.
Output
Efficiencv
Condition
Status
Economizer Type
Carrier 48HJD009- A/C
Packaged DX
1
100,000
0.0
80%AFUE
102,00010.8
EER
New
No Economizer
Carrier 48HJDF008- A/C
Packaged DX
2
100,000
10.4
83%AFUE
90,000
11.0 EER
New
Fixed Temp (Integratec)
System Name Fan Type
Carrier 48HJD009- A/C
Constant Volume
Carrier 48HJDF008- A/C
Constant Volume
Motor Location
SUPPLY
CFM
N
BHP
Motor
Eff.
Drive
Eff.
CFM
RETURN
BHP
FAN
Motor
Eff.
Drive
Eff.
Draw -Through
3,400
2.42
84.0%
97. %%
none
Draw -Through
3,000
1.30
82.5%
97.0%
none
EnergyPro 4.0 by EnergySoft User Number: 1645 Job Number: 040310-3AF Paw: 11 of 16�
41
ENVELOPE MANDATORY MEASURES ENV -AAM
PROJECT NAME
Shops 3A- Famous Footwear
DATE
9/15/2005
DESCRIPTION
Designer
Enforcement
F§ 118(a) Installed Insulating Material shall have been certified by the manufacturer to comply
with the California Quality Standards for insulating material, Title 20, Chapter 4, Article
3.
X❑ § 118(c) All Insulating Materials shall be installed in compliance with the flame spread rating
and smoke density requirements of Sections 2602 and 707 of Title 24, Part 2.
§ 117(a) All Exterior Joints and openings in the building'that are observable sources of air
leakage shall be caulked, gasketed, weatherstripped or otherwise sealed.
XJ § 116(b) Site Constructed Doors, Windows and Skylights shall be caulked between the unit
and the building, and shall be weatherstripped (except for unframed glass doors and
fire doors).
a§ 116(a)1 Manufactured Doors and Windows installed shall have air infiltration rates not
exceeding those shown in Table Number 1-E. of the Standards. Manufactured
fenestration products must be labeled for U -value according to NFRC procedures.
X] .§118(e) Demising Walls in Nonresidential Buildings:
The opaque portions of framed demising walls in nonresidential buildings shall have
insulation with an installed R -value of no less than R-11 between framing members.
EnergyPro By EnergySoft User Number:.User Job Number: 040310-3AF Page: 12 of 16
is
MECHANICAL MANDATORY MEASURES Part 1 of 2 MECH-MM
PROJECT NAME
Shops 3A- Famous Footwear
DATE
9/15/2005
DESCRIPTION
Designer
Enforcement
Equipment and Systems Efficiencies
a §111 Any appliance for which there is a California standard established in the
Appliance Efficiency Regulations will comply with the applicable standard.
X❑ § 115(a) Fan type central furnaces shall not have a pilot light.
X❑ § 123 Piping, except that conveying fluids at temperatures between 60 and 105 degrees
Fahrenheit, or within HVAC equipment, shall be insulated in accordance with
Standards Section 123.
X❑ § 124 Air handling duct systems shall be installed and insulated in compliance with
Sections 601, 603 and 604 of the Uniform Mechanical Code.
Controls
§ 122(e) Each space conditioning system shall be installed with one of the following:
FXJ § 122(e)1A Each space conditioning system serving building types such as offices and
manufacturing facilities (and all others not explicitly exempt from the
requirements of Section 112 (d)) shall be installed with an automatic time switch
with an accessible manual override that allows operation of the system during
off -hours for up to 4 hours. The time switch shall be capable of programming
different schedules for weekdays and weekends and have program backup
capabilities that prevent the loss of the device's program and time setting for at
least 10 hours if power is interrupted; or
❑ § 122(e)1 B An occupancy sensor to control the operating period of the system; or
❑X § 122(e)1C A 4 -hour timer that can be manually operated to control the operating period of
the system.
§ 122(e)2 Each space conditioning system shall be installed with controls that temporarily
restart and temporarily operate the system as required to maintain a setback
heating and/or a setup cooling thermostat setpoint.
X❑ § 122(g) Each space conditioning system serving multiple zones with a combined
conditioned floor area more than 25,000 square feet shall be provided with
isolation zones. Each zone: shall not exceed 25,000 square feet; shall be
provided with isolation devices, such as valves or dampers, that allow the supply
of heating or cooling to be setback or shut off independently of other isolation
areas; and shall be controlled by a time control device as described above.
® § 122(a&b) Each space conditioning system shall be controlled by an individual thermostat
that responds to temperature within the zone. Where used to control heating, the
control shall be adjustable down to 55 degrees F or lower. For cooling, the
control shall be adjustable up to 85 degrees F or higher. Where used for both
heating and cooling, the control shall be capable of providing a deadband of at
least 5 degrees F within which the supply of heating and cooling is shut off or
reduced to a minimum.
X❑ § 122(c) Thermostats shall have numeric setpoints in degrees Fahrenheit (F) and
adjustable setpoint stops accessible only to authorized personnel.
§112(b) Heat pumps shall be installed with controls to prevent electric resistance
supplementary heater operation when the heating load can be met by the heat
pump alone.
EnergyPro By EnergySoft User Number: User Job Number. 040310-3AF Page: 13 of 16
MECHANICAL MANDATORY MEASURES Part 2 of 2 MECH-MM
NAME
Shops 3A- Famous Footwear
DATE
9/15/2005
Description
Designer
Enforcement
Ventilation
F. § 121(e) Controls shall be provided to allow outside air dampers or devices to be operated at
the ventilation rates as specified on these plans.
R§ 122(f) Gravity or automatic dampers interlocked and closed on fan shutdown shall be
provided on the outside air intakes and discharges of all space conditioning and
exhaust systems.
§ 124(f) All gravity ventilating systems shall be provided with automatic or readily accessible
manually operated dampers in all openings to the outside, except for combustion air
openings.
.0 § 121(f)1 Air Balancing: The system shall be balanced in accordance with the National
Environmental Balancing Bureau (NEBB) Procedural Standards (1983), or
Associated Air Balance Council (AABC) National Standards (1989); or
❑ § 121(f)2 Outside Air Certification: The system shall provide the minimum outside air as
shown on the mechanical drawings, and shall be measured and certified by the
installing licensed C-20 mechanical contractor and certified by (1) the design
mechanical engineer, (2) the installing licenced C-20 mechanical contractor, or (3) the
person with overall responsibility for the design of the ventilation system; or
❑ § 121(f)3 Outside Air Measurement: The system shall be equipped with a calibrated local or
remote device capable of measuring the quantity of outside air on a continuous
basis and displaying that quantity on a readily accessible display divice; or
X❑ § 121(f)4 Another method approved by the Commission.
Service Water Heating Systems
❑ § 113(b)2 If a circulating hot water system is installed, it shall have a control capable of
automatically turning off the circulating pump(s) when hot water is not required.
F § 113(b)3B Lavatories in restrooms of public facilities shall be equipped with controls to limit the
outlet temperature to 110 degrees F.
§ 113(b)3C Lavatories in restrooms of public facilities shall be equipped with one of the
following:
Outlet devices that limit the flow of hot water to a maximum of 0.5 gallons per
minute.
Foot actuated control valves, and outlet devices that limit the flow of hot water to a
maximum of 0.75 gallons per minute.
Proximity sensor actuated control valves, and outlet devices that limit the flow of hot
water to a maximum of 0.75 gallons per minute.
Self-closing valves, and outlet devices that limit the flow of hot water to a maximum
of 2.5 gallons per minute, and 0.25 gallons/cycle (circulating system).
Self-closing valves, and outlet devices that limit the flow of hot water to a maximum
of 2.5 gallons per minute, and 0.50 gallons/cycle (non -circulating system).
Self-closing valves, and outlet devices that limit the flow of hot water to a maximum
of 2.5 gallons per minute, and 0.75 gallons/cycle (foot switches and proximity sensor
controls).
EnergyPro By EnergySoft User Number: User Job Number: 040310-3AF Page: 14 of 16
1HVAC SYSTEM HEATING AND COOLING LOADS SUMMARY
PROJECT NAME DATE
Shops 3A- Famous Footwear 9/15/2005
YSTEM NAME FLOOR AREA
Sales/Stock Room -8.5T A/C 2,000
Number of Systems
1
Heating System
Output per System
100,000
Total Output (Btuh)
100,000
Output (Btuh/sgft)
50.0
Cooling System
Output per System
102,000
Total Output (Btuh)
102,000
Total Output (Tons)
8.5
Total Output (Btuhlsgft)
51.0
Total Output (sgft/Ton)
235.3
Air System
CFM per System
3,400
Airflow (cfm)
3,400
Airflow (cfm/sgft)
1.70
Airflow (cfm/Ton)
400.0
Outside Air (%)
15.3
Outside Air (cfm/sgft)
0.26
Note: values above given at ARI conditions
(EATING SYSTEM PSYCHROMETRIi
26.0 OF
Outside
—�—�
519 cfm
69.9 of
63.2 OF
Total Room Loads
Return Vented Lighting
Return Air Ducts
Return Fan
Ventilation
Supply Fan
Supply Air Ducts
TOTAL SYSTEM LOAD
COIL COOLING PEAK
COIL HTG. PEAK
CFM
I Sensible Latent
CFM
Sensible
3,400
60,946
6,042
1,729
38,206
0
305
191
0
0
519
20,003
6,02
519
24,476
0
0
305
191
81,5:6]::12 063 63 064
Carrier 48HJD009- A/C 81,569 11,245 100,000
Total Adjusted System Output 81,569 11,245 100,000
(Adjusted for Peak Design Conditions)
Heating Coil
TIME OF SYSTEM PEAK I Jul 3 pm I I Jan 12 am
im Temperatures at Time of Heating Peak)
90.7 OF 90.7 of
0 Supply Air Ducts
Supply Fan 90.6 OF
3400 cfm ROOMS
70.0 OF
h Return Air Ducts 4
DOLING SYSTEM PSYCHROMETRICS Airstream Temperatures at Time of Cooling Peak
112.0 / 77.7 of 81.6 / 66.5 of 59.2 / 57.9 OF 59.2 / 57.9 of
Supply Air Ducts
Outside Air
519 cfm
Cooling Coil Supply Fan 59.3 / 57.9 of
3400 cfm 53.3% R.H. ROOMS
76.1/64.3 of 76.0 / 64.3 OF
o_...__ .:-'..-.- U!
EnergyPro 4.0 by EnergySoft User Number: 1645 Job Number: 040310-3AF Pane: 15 of 16
HVAC SYSTEM HEATING AND COOLING LOADS SUMMARY
PROJECT NAME DATE
Shops 3A- Famous Footwear 9/15/2005
SYSTEM NAME
FLOOR AREA
Sa1es/T1ts- 2 7.5T A/C 4,500
NE
Number of Systems
2
Heating System
Output per System
100,000
Total Output (Btuh)
200,000
Output (Btuh/sgft)
44.4
Cooling System
Output per System
90,000
Total Output (Btuh)
180,000
Total Output (Tons)
15.0
Total Output (Btuh/sqft)
40.0
Total Output (sgftrTon)
300.0
Air System
CFM per System
3,000
Airflow (cfm)
6,000
Airflow (cfm/sgft)
1.33
Airflow (cfm/Ton)
400.0
Outside Air (%)
18.8
Outside Air (cfm/sgft)
0.25
Note: values above
(EATING SYSTE
26.0 of
Outside Al,
1125 cfm
70.0 of
at ARI conditions
61.7 of
Total Room Loads
Return Vented Lighting
Return Air Ducts
Return Fan
Ventilation
Supply Fan
Supply Air Ducts
TOTAL SYSTEM LOAD
COIL COOLING PEAK
COIL HTG. PEAK
CFM
Sensible
Latent
CFM
Sensible
5,290
84,036
17,072
1,488
36,360
0
420
182
0
0
1,125
43,339
7,698
1,125
53,034
0
0
420
182
128,2 24 770 89 757
Carrier 48HJDF008- A/C 139,509 28,597 200,000
10.4 kW Supplemental Electric 0
Total Adjusted System Output 139,509 28,597 200,000
(Adjusted for Peak Design Conditions)
TIME OF SYSTEM PEAK Jul 3 pm Jan 12 am
im Temperatures at Time of Heating Peak)
92.8 of 92.8 of 92.8 of
0 Supply Air
Ducts
Wv0
Heating Coil Aux. Heat Coil Supply Fan 92.8 r-
6000
6000 cfm ROOMS
70.0 of
o..a...., n:. n.. -a -
(COOLING SYSTEM PSYCHROMETRICS (Airstream Temperatures at Time of Coolina Peak►
12.0 / 77.7 of
Outside Air
1125 cfm
76.1/65.7 OF
82.8 / 68.0 of M 61.1/59.80F
Cooling Coil
Supply Fa
6000 cfm
61.1 / 59.8 of
-� Supply Air Ducts
Fan 61.2/59.8OF
58.3% R.H. ROOMS
76.0 / 65.7 of
h Return Air Ducts `S
EnergyPro 4.0 by EnergySoft User Number. 1645 Job Number: 040310-3AF Page: 16 of 16