Appendix L.2 - Vehicle Miles Traveled (VMT) EvaluationCORAL MOUNTAIN RESORT
DRAFT EIR
SCH# 2021020310
TECHNICAL APPENDICES
Vehicle Miles Traveled Evaluation
Appendix L.2
June 2021
ey URBAN
CROSSROADS
November 2, 2020
Mr. Garret Simon
CM Wave Development, LLC
2440 Junction Place, Suite 200
Boulder, CO 81301
SUBJECT: CORAL MOUNTAIN SPECIFIC PLAN VEHICLE MILES TRAVELED (VMT) ANALYSIS
Dear Mr. Garret Simon:
The following vehicle miles traveled (VMT) analysis has been prepared for the proposed Coral Mountain
Specific Plan (Project) in the City of La Quinta. For VMT analysis purposes, the Project consists of a
master planned themed resort comprised of a wave basin, a 150 -key hotel (with 1,900 square feet bar,
1,400 square feet restaurant, 4,200 square feet kitchen, 1,100 rooftop bar, 1,200 pool bar & grill, and
4,200 square feet spa), 104 attached dwelling units, 496 detached dwelling units, 60,000 square feet of
retail, wave village area (with 900 square feet shape studio, 1,600 square feet surf shop, 3,000 square
feet board room, 1,800 square feet surf lounge/living room, 800 square feet surf classroom, a fitness
pavilion, 1,400 square feet high performance center, and 5,500 square feet beach club), the farm area
(with 2,100 square feet barn, 2,500 square feet greenhouse, 1,400 square feet equipment barn, 300
square feet tool shed, 1,200 square feet family camp, 4,500 square feet gym, 2,000 square feet outfitters,
and 2,000 square feet locker rooms). In addition, back of house complex consists of 9,500 square feet
resort operations, 1,500 square feet wave operations, and 1,000 square feet guardhouses. The wave
basin is a private facility.
Project phasing and long range future traffic conditions with Project land use changes are evaluated in
the Coral Mountain Specific Plan Traffic Impact Analysis (October 27, 2020).
BACKGROUND
Changes to California Environmental Quality Act (CEQA) Guidelines were adopted in December 2018,
which require all lead agencies to adopt VMT as a replacement for automobile delay -based level of
service (LOS) as the new measure for identifying transportation impacts for land use projects. This
statewide mandate was implemented on July 1, 2020. To aid in this transition, the Governor's Office of
Planning and Research (OPR) released a Technical Advisory on Evaluating Transportation Impacts in
CEQA (December of 2018) (Technical Advisory). (1)
Based on OPR's Technical Advisory, the City of La Quinta has prepared their Vehicle Miles Traveled
Analysis Policy (City Guidelines). (2) This analysis has been prepared based on the adopted City
Guidelines.
12615-10 VMT Eval
Mr. Garret Simon
CM Wave Development, LLC
November 2, 2020
Page 2 of 9
VMT ANALYSIS METHODOLOGY
The Vehicle Miles Traveled Analysis Policy (June 2020) (La Quinta Guidelines) are consistent with the
VMT analysis methodology recommended by OPR. As outlined in the La Quinta Guidelines, a Mixed -Use
project such as Coral Mountain, which includes both residential and non-residential uses has each type
of uses analyzed independently, applying the following significance thresholds for each land use
component:
• For Residential Uses, VMT per resident exceeding a level of (1) 15 percent below the Citywide per resident
VMT OR (2) 15 percent below regional VMT per resident, whichever is more stringent
• For Retail Uses (Includes Hotels), a net increase in the total existing VMT for the region.
PROJECT SCREENING
The La Quinta Guidelines provide details on appropriate "screening thresholds" that can be used to
identify when a proposed land use project is anticipated to result in a less -than -significant impact
without conducting a more detailed analysis. Screening thresholds are broken into three types:
• Transit Priority Area (TPA) Screening
• Low VMT Area Screening
• Project Type Screening
A land use project need only to meet one of the above screening thresholds to result in a less -than -
significant impact.
For the purposes of this analysis, the initial VMT screening process has been conducted using the
Riverside County Transportation Analysis Model (RIVTAM).
TPA SCREENING
Consistent with guidance identified in the Technical Advisory, projects located within a Transit Priority
Area (TPA) may be presumed to have a less than significant impact absent substantial evidence to the
contrary. A TPA is defined as within 1/2 mile of:
1) an existing "major transit stop" (a site containing an existing rail transit station, a ferry terminal
served by either a bus or rail transit service, or the intersection of two or more major bus routes
with a frequency of service interval of 15 minutes or less during the morning and afternoon peak
commute periods) or
2) an existing stop along a "high-quality transit corridor" (a corridor with fixed route bus service
with service intervals no longer than 15 minutes during peak commute hours)
However, the presumption may not be appropriate if a project:
• Has a Floor Area Ratio (FAR) of less than 0.75;
12615-10 VMT Eval
��'► URBAN
CROSSROADS
Mr. Garret Simon
CM Wave Development, LLC
November 2, 2020
Page 3 of 9
• Includes more parking for use by residents, customers, or employees of the project than required by the
jurisdiction (if the jurisdiction requires the project to supply parking);
• Is inconsistent with the applicable Sustainable Communities Strategy (as determined by the lead agency,
with input from the Metropolitan Planning Organization); or
• Replaces affordable residential units with a smaller number of moderate- or high-income residential units.
The Project site is not located within 1/2 mile of an existing major transit stop, or along a high-quality
transit corridor.
The TPA screening threshold is not met.
Low VMT AREA SCREENING
The La Quinta Guidelines also states that, "residential and office projects located within a low VMT-
generating area may be presumed to have a less than significant impact absent substantial evidence to
the contrary. In addition, other employment-related and mixed-use land use projects may qualify for the
use of screening if the project can reasonably be expected to generate VMT per resident, per worker, or
per service population that is similar to the existing land uses in the low VMT area." The sub -regional
Riverside County Transportation Analysis Model (RIVTAM) is used to measure VMT performance within
individual traffic analysis zones (TAZs). An estimate of the VMT in the Project's physical location was
calculated to determine the relevant TAZ's VMT as compared to the jurisdictional average (see
Attachment B). The Project is located in TAZ 4742, and would not appear to be within a low VMT
generating TAZ.
The Low VMT Area screening threshold is not met.
PROJECT TYPE SCREENING
The retail component of the Project is anticipated to serve the local area. The La Quinta Guidelines allow
retail projects of less than 50,000 square feet to be screened out. Because the retail component of the
Project is more than 50,000 square feet, the retail portion of the Project is not screened out. The La
Quinta Guidelines identify projects that are local serving by nature, or that generate fewer than 110 daily
vehicle trips be presumed to have a less -than -significant impact on VMT. Based on the Project's trip
generation (see Attachment A), the Project is not considered a local serving or small enough to not
warrant assessment, therefore, the Project would not be eligible to screen out based on project type
screening.
The Project Type screening threshold is not met.
Since none of the project level screening criteria were met, a project level VMT analysis has been
prepared.
12615-10 VMT Eval
��'► URBAN
CROSSROADS
Mr. Garret Simon
CM Wave Development, LLC
November 2, 2020
Page 4 of 9
PROJECT VMT ASSESSMENT
RIVTAM is a useful tool to estimate VMT as it considers interaction between different land uses based
on socio-economic data such as population, households and employment. The La Quinta Guidelines
identifies RIVTAM as the appropriate tool for conducting VMT analysis for land use projects in Riverside
County.
Project VMT has been calculated using the most current version of RIVTAM. Adjustments in socio-
economic data (SED) (i.e., employment) have been made to a separate TAZ within the RIVTAM model to
reflect the Project's proposed population and employment uses. Separate TAZs are used to isolate the
Project's VMT.
Table 1 summarizes the service population (population and employment) estimates for the Project. It
should be noted that the employment estimates have been developed from land use to employment
generation factors from the Riverside County General Plan but modified for the specific Project
characteristics and then confirmed with the Client. The wave basin and ancillary resort land uses are
private, for use of residents and resort hotel guests. Although the Project employment is a mix of service
and retail employment, the City of La Quinta guidelines are explicit indicating that the hotel land uses
are categorized as retail uses for the purposes of VMT analysis.
TABLE 1: POPULATION AND EMPLOYMENT ESTIMATES
Land Use
Estimated Service Population
Residential
1,698 Residents
Hotel / Wave Basin
434 Employees
Commercial Retail
240 Employees
Hotel
300 Hotel Occupants
Total:
2,672 Service Population
Adjustments to popu ation and employment factors for the Project TAZ were made to the RIVTAM base
year model (2012) and the cumulative year model (2040). Each model was then run with the updated
SED factors included for the Project TAZ.
PROJECT RESIDENTIAL VMT CALCULATION
Consistent with recommendations contained in the La Quinta Guidelines, the residential calculation of
VMT is based upon the home-based project -generated VMT per population. This calculation focuses on
the occupants of dwelling units within the Project land uses, whereas hotel occupants, wave basin
visitors and retail patrons are evaluated separately using the boundary method discussed below. Table
2 shows the home-based VMT associated with the Project for both baseline and cumulative conditions.
VMT estimates are provided for both the base year model (2012) and cumulative year model (2040), and
linear interpolation was used to determine the Project's home-based baseline (2020) VMT.
12615-10 VMT Eval
0 URBAN
CROSSROADS
Mr. Garret Simon
CM Wave Development, LLC
November 2, 2020
Page 5 of 9
TABLE 2: BASELINE AND CUMULATIVE PROJECT RESIDENTIAL HOME-BASED VMT
For baseline (2020) conditions, the residential portion of the Project generates 19,773 Home -Based VMT.
There are an estimated 1,698 Project residents. The result is approximately 11.64 home-based VMT /
Capita for the 2020 Baseline with Project conditions. In addition, the cumulative (2040) Project scenario
results in approximately 12.14 VMT / SP.
For comparison purposes, Citywide home-based VMT estimates have been also developed from the
"with Project" RIVTAM model run for baseline conditions. Once total home-based VMT for the area is
calculated, total area VMT is then normalized by dividing by the population as shown on Table 3.
TABLE 3: BASE YEAR CITYWIDE HOME-BASED VMT
Category
Project 2012
Project 2040
Project 2020
(interpolated)
Residents
1,698
1,698
1,698
VMT
19,437
20,642
19,773
VMT / Resident
11.45
12.14
11.64
For baseline (2020) conditions, the residential portion of the Project generates 19,773 Home -Based VMT.
There are an estimated 1,698 Project residents. The result is approximately 11.64 home-based VMT /
Capita for the 2020 Baseline with Project conditions. In addition, the cumulative (2040) Project scenario
results in approximately 12.14 VMT / SP.
For comparison purposes, Citywide home-based VMT estimates have been also developed from the
"with Project" RIVTAM model run for baseline conditions. Once total home-based VMT for the area is
calculated, total area VMT is then normalized by dividing by the population as shown on Table 3.
TABLE 3: BASE YEAR CITYWIDE HOME-BASED VMT
Category
City of La Quinta
VMT
544,993
Population
42,000
VMT / Resident
12.98
The estimates of baseline residential home-based Project VMT / Capita are compared to the City of La
Quinta VMT of 12.98 home-based VMT/ Capita. The City of La Quinta guidelines indicate that residential
VMT exceeding 15 percent below the Citywide VMT per resident (11.03 VMT / capita) represents a
Project impact. The Project home-based VMT / Capita of 11.64 is greater than the City VMT / Capita
threshold, and a potentially significant VMT impact is indicated.
PROJECT EMPLOYMENT IMPACT ON VMT
As noted above, the VMT analysis methodology for retail uses (including hotels) focuses on the net
increase in the total existing VMT for the region. The project consists of approximately 674 employees,
including 240 employees associated with the 60,000 square feet of neighborhood shopping center retail
uses and 434 employees associated with the hotel and wave basin uses.
Travel activity associated with total link -level VMT was extracted from the "without Project" and "with
non-residential Project" RIVTAM model run for 2012 and 2040 conditions, then interpolated for baseline
(2020) conditions. This methodology is commonly referred to as "boundary method" and includes the
total VMT for all vehicle trips with one or both trip ends within a specific geographic area. The "boundary
method" VMT per service population for the CVAG subregion is utilized to normalize VMT into a standard
unit for comparison purposes, focusing on the total population and employment in the Coachella
12615-10 VMT Eval
��'► URBAN
CROSSROADS
Mr. Garret Simon
CM Wave Development, LLC
November 2, 2020
Page 6 of 9
Valley. Once total VMT for the area is calculated, total area VMT is then normalized by dividing by the
respective service population (i.e., population and employment of the Coachella Valley) as shown on
Table 4.
TABLE 4: BASE YEAR SUB -REGIONAL LINK -LEVEL VMT
To determine whether or not there is a significant impact using the boundary method, CVAG area VMT
with the project employment is compared to without project conditions. The CVAG subregion VMT / SP
without Project employment is estimated at 21.56, whereas with the Project employment, the CVAG
subregion VMT is estimated at 21.53. The project's effect on VMT (for non-residential uses) is not
considered significant because it results in a cumulative link -level boundary CVAG VMT per service
population decrease under the plus project condition compared to the no project condition.
PROJECT DESIGN FEATURES FOR VMT REDUCTION
Transportation demand management (TDM) strategies have been evaluated for the purpose of reducing
VMT impacts determined to be potentially significant. Quantifying Greenhouse Gas Mitigation
Measures, (CAPCOA) 2010 provides information on individual understand potential reduction in VMT.
Of the 50 transportation measures presented by CAPCOA, approximately 41 are applicable at a building
and site level. The remaining 9 measures are functions of, or depend on, site location and/or actions by
local and regional agencies or funders.
CAPCOA indicates that a ten percent is the maximum reduction when combining multiple mitigation
strategies for the suburban place type (characterized by dispersed, low-density, single -use, automobile
dependent land use patterns) and requires a project to contain a diverse land use mix, workforce
housing, and project -specific transit. The maximum percent reductions were derived from a limited
comparison of aggregate citywide VMT performance rather than based on data comparing the actual
performance of VMT reduction strategies in the place type.
Even under the most favorable circumstances, projects located within a suburban context, such as the
proposed Project evaluated here, can realize a maximum 10 percent reduction in VMT through
implementation of feasible TDM measures. The Project incorporates design features and attributes
promoting trip reduction. Because these features/attributes are integral to the Project, and/or are
regulatory requirements, they are not considered to be mitigation measures. However, the RIVTAM
does not incorporate modeling of these features, so they are considered after the VMT data is extracted
from the traffic model.
12615-10 VMT Eval
��'► URBAN
CROSSROADS
Without Project
Employment
With Project
Employment
VMT Interacting with CVAG Area
15,173,739
15,166,580
CVAG Area Population
510,550
510,550
CVAG Area Employment
193,090
193,764
VMT / Service Population
21.56
21.53
To determine whether or not there is a significant impact using the boundary method, CVAG area VMT
with the project employment is compared to without project conditions. The CVAG subregion VMT / SP
without Project employment is estimated at 21.56, whereas with the Project employment, the CVAG
subregion VMT is estimated at 21.53. The project's effect on VMT (for non-residential uses) is not
considered significant because it results in a cumulative link -level boundary CVAG VMT per service
population decrease under the plus project condition compared to the no project condition.
PROJECT DESIGN FEATURES FOR VMT REDUCTION
Transportation demand management (TDM) strategies have been evaluated for the purpose of reducing
VMT impacts determined to be potentially significant. Quantifying Greenhouse Gas Mitigation
Measures, (CAPCOA) 2010 provides information on individual understand potential reduction in VMT.
Of the 50 transportation measures presented by CAPCOA, approximately 41 are applicable at a building
and site level. The remaining 9 measures are functions of, or depend on, site location and/or actions by
local and regional agencies or funders.
CAPCOA indicates that a ten percent is the maximum reduction when combining multiple mitigation
strategies for the suburban place type (characterized by dispersed, low-density, single -use, automobile
dependent land use patterns) and requires a project to contain a diverse land use mix, workforce
housing, and project -specific transit. The maximum percent reductions were derived from a limited
comparison of aggregate citywide VMT performance rather than based on data comparing the actual
performance of VMT reduction strategies in the place type.
Even under the most favorable circumstances, projects located within a suburban context, such as the
proposed Project evaluated here, can realize a maximum 10 percent reduction in VMT through
implementation of feasible TDM measures. The Project incorporates design features and attributes
promoting trip reduction. Because these features/attributes are integral to the Project, and/or are
regulatory requirements, they are not considered to be mitigation measures. However, the RIVTAM
does not incorporate modeling of these features, so they are considered after the VMT data is extracted
from the traffic model.
12615-10 VMT Eval
��'► URBAN
CROSSROADS
Mr. Garret Simon
CM Wave Development, LLC
November 2, 2020
Page 7 of 9
Project vehicle miles traveled (VMT) are reduced by the following Project design features/attributes,
which are anticipated to collectively reduce Project home-based VMT by approximately 6%:
• Having different types of land uses near one another can decrease VMT since trips between
land use types are shorter and may be accommodated by non -auto modes of transport. For
example, when residential areas are in the same neighborhood as commercial and resort land
uses, a resident does not need to travel outside of the neighborhood to meet his/her
recreational and retail needs. The Project's mixed-use environment could provide for a
potential reduction in Project residential VMT of 3%.
• The project will include improved design elements to enhance walkability and connectivity.
Improved street network characteristics within the Project include sidewalk coverage,
building setbacks, street widths, pedestrian crossings, presence of street trees, and a host of
other physical variables that differentiate pedestrian -oriented environments from auto -
oriented environments. The Project would provide a pedestrian access network that
internally links all uses and connects to all existing or planned external streets and pedestrian
facilities contiguous with the project site. The Project would minimize barriers to pedestrian
access and interconnectivity. The Project includes sidewalk connections, particularly to / from
the retail areas interacting with residential and resort uses on-site. The Project's
implementation of this measure could provide for a potential reduction in Project residential
VMT of 2%.
• The project will implement marketing strategies to optimize on-site resort and residential
uses. Information sharing and marketing are important components to successful trip
reduction strategies. Marketing strategies may include:
o Resident member benefits that include use of the resort amenities
o Event promotions
o Publications
The Project's implementation of this measure could provide for a potential reduction in
Project residential VMT of 1%.
In summary, travel demand modeling of VMT for the Project based upon City of La Quinta guidelines
indicates a potential impact for residential uses while also indicating the Project's non-residential uses
do not exceed VMT thresholds. Project design features taken into account after the modeling process
reduce residential VMT from 11.64 VMT / resident to 10.94 VMT per resident, which is less than the
City's VMT residential threshold. The unique mixed-use characteristics of the Project, combined with
walkability and connectivity design elements, optimize on-site interaction and result in a lower VMT than
standalone uses.
12615-10 VMT Eval
0 URBAN
CROSSROADS
Mr. Garret Simon
CM Wave Development, LLC
November 2, 2020
Page 8 of 9
If you have any questions, please contact us at (949) 375-2435 for John or (714) 585-0574 for Marlie.
Respectfully submitted,
URBAN CROSSROADS, INC.
A... e„L._.
John Kain, AICP
Principal
LI/la/tit-
Marlie Whiteman, PE
Senior Associate
12615-10 VMT Eval
L?► URBAN
CROSSROADS
Mr. Garret Simon
CM Wave Development, LLC
November 2, 2020
Page 9 of 9
REFERENCES
1. Office of Planning and Research. Technical Advisory on Evaluating Transportation Impacts in CEQA.
State of California : s.n., December 2018.
2. City of La Quinta. Vehicle Miles Traveled Aanlysis Policy. June 23, 2020.
3. County of Riverside. Appendix E: Socioeconomic Build -Out Assumptions and Methodology. County of
Riverside : s.n., April 2017.
12615-10 VMT Eval
L?► URBAN
CROSSROADS
Attachment A
Project Trip Generation
12615-10 VMT Eval
L.► URBAN
CROSSROADS
The Wave - Carol Mountuln
TABLE 4-3. PROJECT BUILDOUT 202G) TRIP GENERATION SUMMARY
Trip Generation Rates'
Land Use
FTE LU
Quantity''
AM Peak Hour
PM Peak Hour
Daily
Land Use
Code
Quantity'
In
Out
Tobi
In
Out
Tots
pally
Single Family Detached
210
496 DU
0.19
0.55
0174
0.62
0.37
0.99
9.44
Multifamily Housing (Low -Rise)
220
104 DU
011
0.35
0.46
0.35
0.21
0.56
7.32
Resort Hotel
330
150 RM
0.27
0.10
0.37
0.20
0.27
0.47
7.87
Shopping Center
820
60 TSF
0.58
0.36
0.94
1.83
1.98
3.81
37.75
Wave Pool Facility
-°
12 AC
1.20
0.80
2-00
2.40
1.60
4.00
50.00
Trip Generation Results
Land Use
ITE LU
Code.
Quantity''
AM Peak Hour
PM Peak Hour
Daily
In
Out
Total
in
Out
Total
Single Family (Detached
210
496 DU
94
273
367
308
184
492
4,682
Multifamily Housing (Low -Rise)
220
104 DU
11
36
47
36
22
58
761
Internal to Retail/Resort
(10)
(20)
(30)
(40)
(29)
(69)
(595)
Residential External Trips
95
289
384
304
177
481
4$48
Shopping Center
820
60 TSF
35
22
57
110
119
229
2,265
Pass -By (25%)
(7)
(7)
(14)
(28)
(28)
(56)
(566)
Internal to Residential/Resort
(9)
(7)
(16)
(21)
(35)
(56)
()
Shopping Center External Trips
19
8
27
61
56
117
1,251
Resort Hotel
330
150 RM
41
15
56
30
41
71
1,181
Internal to Residential/Retail
(14)
(10)
(24)
(13)
(21)
(36)
(416)
Resort Hotel External Trips
27
5
32
15
20
35
765
Wave Pool Facility
-°
12 AC
14
10
24
29
19
48
600
internal to Residential/Retail/Resort
(12)
(8)
(20)
(26)
(17)
(43)
(470)
Wave Pool Facility External Trips
2
2
4
3
2
5
130
Project Subtotal
195
356
551
513
385
898
9,489
internal Capture Subtotal
(45)
(45)
(90)
(102)
(102)
(204)
(1,929)
Pass -By (Shopping Center)
(7)
(7)
(14)
(28)
(28)
(56)
(566)
Project Total External Trips
143
304
447
383
255
638
6,994
1rip Generation Source- Institute of Transportation Engineers (ITE), Trip Generation Manual, lath Edition (2017).
DU .Dwelling Unit; RM . Occupied Room; TSF . Thousand Square Feet
Pass-ftySource! Shops at Coral Mountain TCA., prepared by Urban Crossroads, Inc. {November 2009)-
; Since WE does not have tdp rates Fora wave pool facility, similar use based on S4NDAGs recreation park (developed) peak hour and daily rates are utilized.
a-Ws4_1250o-t700o4125.t345ra-11r12533 - rt r+rrip ser
12615-10 VMT Eval
L?► URBAN
CROSSROADS
12615-10 VMT Eval
0 URBAN
CROSSROADS
Attachment B
Low VMT Area Screening Calculations
12615-10 VMT Eval
Lam► URBAN
CROSSROADS
RivTAM 4742 HB VMT
Z:\Shared\UcJobs\_12600-13000\12600\12615_partial\Excel\
Vehicle Flow OD Method
OD Method Vehicle Miles Traveled
Base Year (2012)
TAZ 4742
Total
390
Automobiles
363
Trucks
26
OD Method Vehicle Miles Traveled
Trip Length
Base Year (2012)
TAZ 4742
VMT OD Total
5,119
VMT OD Automobiles
4,114
VMT OD Trucks
1,005
Trip Length
Vehicle Flow PA Method
Base Year (2012)
TAZ 4742
HB
3
PA Method Vehicle Miles Traveled
VMT HB
Base Year (2012)
TAZ 4742
72
CALLE TAMP.
478
0• .......... a
m
- z
404
•n
ial
GP. ...... --474---------
\
47.13
Trip Length
Base Year (2012)
TAZ 4742
Total
22.73
SED
Base Year (2012) Summary
TAZ 4742
Pop
3
SP
53
TAZ 4742 - No Project 2012
OD VMT/SP
PA HB VMT/POP
Base Year (2012)
TAZ 4742
Total
13.14
Automobiles
11.32
Trucks
38.42
Vehicle Flow PA Method
Base Year (2012)
TAZ 4742
HB
3
PA Method Vehicle Miles Traveled
VMT HB
Base Year (2012)
TAZ 4742
72
CALLE TAMP.
478
0• .......... a
m
- z
404
•n
ial
GP. ...... --474---------
\
47.13
Trip Length
Base Year (2012)
TAZ 4742
Total
22.73
SED
Base Year (2012) Summary
TAZ 4742
Pop
3
SP
53
TAZ 4742 - No Project 2012
OD VMT/SP
PA HB VMT/POP