Loading...
BRES2017-0329 Certificate of InstallationCERTIFICATE OF INSTALLATION CF2R-MCH-01-E Space Conditioning Systems, Ducts, and Fans (Page 1 of 19) Project Name: Via Dona Project Enforcement Agency: City of La Quinta Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. General Information 01 Dwelling Unit Name Unit 1 02 Climate Zone 15 03 Dwelling Unit Total Conditioned Floor Area (ft2) 5527 04 Number of Space Conditioning Systems in this dwelling unit. 7 05 Certificate of Compliance Type Performance (CF1R-PRF) 06 Method Used to Calculate HVAC Loads ACCA Manual J 07 Calculated Dwelling Unit Sensible Cooling Load (Btu/h) 60000 Amy 08 Calculated Dwelling Unit Heating Load (Btu/h) 80000 09 Dwelling Unit Number of Bedrooms 5 111111111,_,!r it__31 I ( MCH-01a - Space Conditioning Systems Ducts and Fans - For use with Performance Certificate of Compliance Registration Number: 219-P010089040A-000-001-M01001A-0000 Registration Date/Time: 2019-04-17 12:19:18 HERS Provider: CalCERTS CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version: 2018.0.001 Report Generated: 2019-04-17 11:25:20 Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-01-E Space Conditioning Systems, Ducts, and Fans (Page 2 of 19) B. Design Space Conditioning (SC) System Component Specifications from CF1R This table reports the space conditioning system features that were specified on the registered CF1R-PRF compliance document for this project. 01 02 03 04 05 06 07 08 09 10 11 12 Zone Name SC System Identification or Name SC System Type Heating System Type Cooling System Type SC Fan Type Distribution System Type Required Thermostat Type Low Leakage Air -Handling Unit (LLAHU) Status Bypass Duct Status Cooling Zoning Type Cooling System Compressor Speed This field or section is not applicable System 1 Heating and cooling system other Central gas furnace Central split AC PSC Permanent Split Capacitor Unconditione d attic Setback No, credit is not taken No Bypass Duct Not Zonal Multi -speed This field or section is not applicable System 2 Heating and cooling system other Central gas furnace Central split AC PSC Permanent Split Capacitor Unconditione d attic j owe Setbacknot No, credit is taken No Bypass Duct Not Zonal Multi speed This field or section is not applicable System 3 Heating and cooling system other Central gas furnace Central split AC PSC Permanent Split Capacitor Unconditione d attic Setback No, credit is not taken No Bypass Duct Not Zonal Multi -speed This field or section is not applicable System 4 Heat pump heating cooling Central split HP Central split HP PSC Permanent Split Capacitor Unconditione d attic Setback No, credit is not taken No Bypass Duct Not Zonal Multi -speed This field or section is not applicable System 5 Heat pump heating cooling Central split HP Central split HP PSC Permanent Split Capacitor Unconditione d attic Setback No, credit is not taken No Bypass Duct Not Zonal Multi -speed Registration Number: 219-P010089040A-000-001-M01001A-0000 Registration Date/Time: 2019-04-17 12:19:18 HERS Provider: CaICERTS CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:25:20 CERTIFICATE OF INSTALLATION CF2R-MCH-01-E Space Conditioning Systems, Ducts, and Fans (Page 3 of 19) B. Design Space Conditioning (SC) System Component Specifications from CF1R This table reports the space conditioning system features that were specified on the registered CF1R-PRF compliance document for this project. 01 02 03 04 05 06 07 08 09 10 11 12 Zone Name SC System Identification or Name SC System Type Heating System Type Cooling System Type SC Fan Type Distribution System Type Required Thermostat Type Low Leakage Air -Handling Unit (LLAHU) Status Bypass Duct Status Cooling Zoning Type Cooling System Compressor Speed This field or section is not applicable System 6 Heat pump heating cooling Central split HP Central split HP PSC Permanent Split Capacitor Unconditione d attic Setback No, credit is not taken No Bypass Duct Not Zonal Multi -speed This field or section is not applicable System 7 Heat pump heating cooling Central split HP Central split HP PSC Permanent Split Capacitor Unconditione d attic Setbacknot No credit is taken No Bypass Duct Not Zonal Multi speed Notes: Registration Number: 219-P010089040A-000-001-M01001A-0000 Registration Date/Time: 2019-04-17 12:19:18 HERS Provider: CaICERTS CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version: 2018.0.001 Report Generated: 2019-04-17 11:25:20 Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-01-E Space Conditioning Systems, Ducts, and Fans (Page 4 of 19) C. Design Space Conditioning (SC) System Compliance Requirements from CF1R This table reports the space conditioning system features that were specified on the registered CF1R-PRF compliance document for this project. 01 02 03 04 05 06 07 08 09 10 SC System Identification or Name Heating Efficiency Type Minimum Heating Efficiency Value Heat Pump Heating Capacity at 47°F Heat Pump Heating Capacity at 17°F Minimum Cooling Efficiency SEER Minimum Cooling Efficiency EER Minimum Cooling System Airflow Rate (CFM/ton) Maximum Fan Efficacy (W/CFM) Minimum Duct R-Value System 1 Annual Fuel Utilization Efficiency (AFUE) 80 This field or section is not applicable This field or section is not applicable 18 13 350 0.58 R-8 System 2 Annual Fuel Utilization Efficiency (AFUE) 80 This field or section is not applicable This field or section is not applicable 18 13 350 0.58 R-8 System 3 Annual Fuel Utilization Efficiency (AFUE) 80 This field or section is not applicable This field or section is not applicable 18 13 350 0.58 R-8 System 4 Heating Seasonal Performance Factor (HSPF) 10.5 27000 17300 16.5 12.3 350 0.58 R-8 System 5 Heating Seasonal Performance Factor (HSPF) 10.5 27000 17300 16.5 12.3 350 0.58 R-8 Registration Number: 219-P010089040A-000-001-M01001A-0000 Registration Date/Time: 2019-04-17 12:19:18 HERS Provider: CaICERTS CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:25:20 CERTIFICATE OF INSTALLATION CF2R-MCH-01-E Space Conditioning Systems, Ducts, and Fans (Page 5 of 19) C. Design Space Conditioning (SC) System Compliance Requirements from CF1R This table reports the space conditioning system features that were specified on the registered CF1R-PRF compliance document for this project. 01 02 03 04 05 06 07 08 09 10 SC System Identification or Name Heating Efficiency Type Minimum Heating Efficiency Value Heat Pump Heating Capacity at 47°F Heat Pump Heating Capacity at 17°F Minimum Cooling Efficiency SEER Minimum Cooling Efficiency EER Minimum Cooling System Airflow Rate (CFM/ton) Maximum Fan Efficacy (W/CFM) Minimum Duct R-Value System 6 Heating Seasonal Performance Factor (HSPF) 10.5 27000 17300 16.5 12.3 350 0.58 R-8 System 7 Heating Seasonal Performance Factor (HSPF) 10.5 27000 17300 16.5 12.3 350 0.58 R-8 Notes: D. Installed Space Conditioning (SC) System Component Information 01 02 03 04 05 06 07 08 09 10 11 SC System Identification or Name SC System Location or Area Served Conditioned Floor Area Served by the System (ft2) Heating System Type Cooling System Type SC Fan Type Distribution System Type SC System Thermostat Type Cooling Zoning Type Cooling System Compressor Speed Type Central Fan Integrated (CFI) Ventilation System Status System 1 GREATROOM/ KITCHEN 1000 Central gas furnace Central split AC PSC Permanent Split Capacitor Unconditioned attic Setback Not Zonal Multi -speed Not a CFI system Registration Number: 219-P010089040A-000-001-M01001A-0000 Registration Date/Time: 2019-04-17 12:19:18 HERS Provider: CaICERTS CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:25:20 CERTIFICATE OF INSTALLATION CF2R-MCH-01-E Space Conditioning Systems, Ducts, and Fans (Page 6 of 19) D. Installed Space Conditioning (SC) System Component Information 01 02 03 04 05 06 07 08 09 10 11 SC System Identification or Name SC System Location or Area Served Conditioned Floor Area Served by the System (ft2) Heating System Type Cooling System Type SC Fan Type Distribution System Type SC System Thermostat Type Cooling Zoning Type Cooling System Compressor Speed Type Central Fan Integrated (CFI) Ventilation System Status System 2 KITCHEN 1000 Central gas furnace Central split AC PSC Permanent Split Capacitor Unconditioned attic Setback Not Zonal Multi -speed Not a CFI system System 3 MASTER 827 Central gas furnace Central split AC PSC Permanent Split Capacitor Unconditioned attic Setback Not Zonal Multi -speed Not a CFI system System 4 LOWER OUTSIDE SUITE 675 Central split HP Central split HP PSC Permanent Split Capacitor Unconditioned attic Setback Not Zonal Multi -speed Not a CFI system System 5 LOWER INNER SUITE 675 Central split HP Central split HP PSC Permanent Split Capacitor Unconditioned attic Setback Not Zonal Multi -speed Not a CFI system System 6 UPPER POOL SUITE 675 Central split HP Central split HP PSC Permanent Split Capacitor Unconditioned attic Setback Not Zonal Multi -speed Not a CFI system System 7 UPPER ENTRY SUITE 675 Central split HP Central split HP PSC Permanent Split Capacitor Unconditioned attic Setback Not Zonal Multi -speed Not a CFI system Notes: Registration Number: 219-P010089040A-000-001-M01001A-0000 Registration Date/Time: 2019-04-17 12:19:18 HERS Provider: CaICERTS CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:25:20 CERTIFICATE OF INSTALLATION CF2R-MCH-01-E Space Conditioning Systems, Ducts, and Fans (Page 7 of 19) E. Installed Heating System Equipment Information (not heat pumps) 01 02 03 04 05 06 07 08 SC System Identification or Name SC System Location or Area Served Heating Efficiency Type Heating Efficiency Value Heating Unit Manufacturer Heating Unit Model Number Heating Unit Serial Number Rated Heating Capacity, Output (Btu/h) System 1 GREATROOM /KITCHEN Annual Fuel Utilization Efficiency (AFUE) 80 GOODMAN AMVC80805CXCA 1812102895 64000 System 2 KITCHEN Annual Fuel Utilization Efficiency (AFUE) 80 GOODMAN AMVC80805CXCA 18106167732 64000 System 3 MASTER Annual Fuel Utilization Efficiency (AFUE) 80 �M iii GOODMAN i MS IL E R 1 AMVC80805CXCA 1812102894 ROVIDE 64000 Notes: Registration Number: 219-P010089040A-000-001-M01001A-0000 Registration Date/Time: 2019-04-17 12:19:18 HERS Provider: CaICERTS CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version: 2018.0.001 Report Generated: 2019-04-17 11:25:20 Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-01-E Space Conditioning Systems, Ducts, and Fans (Page 8 of 19) F. Installed Cooling System Outdoor Condensing Unit or Package Unit Equipment Information (not heat pumps) 01 02 03 04 05 06 07 08 09 SC System Identificatio n or Name SC System Location or Area Served Cooling Efficiency SEER Cooling Efficiency EER Condenser or Package Unit Manufacturer Condenser or Package Unit Model Number Condenser or Package Unit Serial Number System Rated Cooling Capacity at Design Conditions (Btu/h) Condenser Rated Nominal Capacity (ton) System 1 GREATROO M/KITCHEN 18.8 13 GOODMAN AVXC200601AE 1811187417 60000 5 System 2 KITCHEN 21 13 GOODMAN AVXC200361AE 1807328244 36000 3 System 3 MASTER 18.8 13 GOODMAN AVXC200601AE 181187418 60000 5 Notes: G. Installed Split System Indoor Coil or Fan Coil Unit Equipment Information (applicable to DX or hydronic heating/cooling coils or fan coil units) Systems with more than one indoor coil or fan coil unit (e.g. multi -split systems) shall provide information for each of the system indoor coils or fan coil units. 01 02 03 04 05 SC System Identification or Name SC System Location or Area Served Indoor Coil or Fan Coil Unit Manufacturer Indoor Coil or Fan Coil Unit Model Number Indoor Coil or Fan Coil Unit Serial Number System 1 GREATROOM/KITC ASPEN CC60G44245L004 H18-00012091 System 2 KITCHEN US ALUMACOIL CAPF3743C6DB 1901004262 System 3 MASTER ASPEN CC60G44245L004 H18-00012092 Registration Number: 219-P010089040A-000-001-M01001A-0000 Registration Date/Time: 2019-04-17 12:19:18 HERS Provider: CaICERTS CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:25:20 CERTIFICATE OF INSTALLATION CF2R-MCH-01-E Space Conditioning Systems, Ducts, and Fans (Page 9 of 19) G. Installed Split System Indoor Coil or Fan Coil Unit Equipment Information (applicable to DX or hydronic heating/cooling coils or fan coil units) Systems with more than one indoor coil or fan coil unit (e.g. multi -split systems) shall provide information for each of the system indoor coils or fan coil units. 01 02 03 04 05 SC System Identification or Name SC System Location or Area Served Indoor Coil or Fan Coil Unit Manufacturer Indoor Coil or Fan Coil Unit Model Number Indoor Coil or Fan Coil Unit Serial Number System 4 LOWER OUTSIDE SUITE DAIKIN FDMQ24RVJU E000329 System 5 LOWER INNER SUITE DAIKIN FDMQ18RVJU E000149 System 6 UPPER POOL SUITE DAIKIN FDMQ24RVJU E000332 System 7 UPPER ENTRY SUITE DAIKIN FDMQ24RVJU E000333 Notes: H. Installed Heat Pump System - Split System Condensing Unit or Package Unit Equipment Information 01 02 03 04 05 SC System Identification or Name SC System Location or Area Served Condenser or Package Unit Manufacturer Condenser or Package Unit Model Number Condenser or Package Unit Serial Number System 4 LOWER OUTSIDE SUITE DAIKIN RX24RMVJU G000972 System 5 LOWER INNER SUITE DAIKIN RX18RMVJU G001163 System 6 UPPER POOL SUITE DAIKIN RX24RMVJU G001027 Registration Number: 219-P010089040A-000-001-M01001A-0000 Registration Date/Time: 2019-04-17 12:19:18 HERS Provider: CaICERTS CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:25:20 CERTIFICATE OF INSTALLATION CF2R-MCH-01-E Space Conditioning Systems, Ducts, and Fans (Page 10 of 19) H. Installed Heat Pump System - Split System Condensing Unit or Package Unit Equipment Information 01 02 03 04 05 SC System Identification or Name SC System Location or Area Served Condenser or Package Unit Manufacturer Condenser or Package Unit Model Number Condenser or Package Unit Serial Number System 7 UPPER ENTRY SUITE DAIKIN RX24RMVJU G001149 Notes: I. Installed Heat Pump System -Efficiency and Performance Compliance Information 01 02 03 04 05 06 07 08 09 10 SC System Identification or Name SC System Location or Area Served Heating Efficiency Type Heating Efficiency Value ‘I, System Heating Capacity Rated at 47°F CD System Heating Capacity Rated at 17°F -C System Rated Cooling Efficiency SEER pur% System Rated Cooling Efficiency EER System Rated Cooling Capacity at Design Conditions (Btu/h) Condenser Rated Nominal Capacity (ton) System 4 LOWER OUTSIDE SUITE Heating Seasonal Performance Factor (HSPF) 10.5 27000 17300 18.6 12.5 24000 2 System 5 LOWER INNER SUITE Heating Seasonal Performance Factor (HSPF) 10.5 27000 17300 18.5 12.5 18000 1.5 System 6 UPPER POOL SUITE Heating Seasonal Performance Factor (HSPF) 10.5 27000 17300 18.6 12.5 24000 2 Registration Number: 219-P010089040A-000-001-M01001A-0000 Registration Date/Time: 2019-04-17 12:19:18 HERS Provider: CaICERTS CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:25:20 CERTIFICATE OF INSTALLATION CF2R-MCH-01-E Space Conditioning Systems, Ducts, and Fans (Page 11 of 19) I. Installed Heat Pump System -Efficiency and Performance Compliance Information 01 02 03 04 05 06 07 08 09 10 SC System Identification or Name SC System Location or Area Served Heating Efficiency Type Heating Efficiency Value System Rated Heating Capacity at 47°F System Rated Heating Capacity at 17°F System Rated Cooling Efficiency SEER System Rated Cooling Efficiency EER System Rated Cooling Capacity at Design Conditions (Btu/h) Condenser Rated Nominal Capacity (ton) System 7 UPPER ENTRY SUITE Heating Seasonal Performance Factor (HSPF) 10.5 27000 17300 18.6 12.5 24000 2 Notes: J. Installed Duct System Information 01 02 03 04 05 06 07 08 09 10 11 12 SC System Identification or Name SC System Location or Area Served Supply Duct Location Supply Duct R-Value Return Duct Location Return Duct R-Value Exemption from Min R-Value for Ducts In Conditioned Space Method of compliance with duct and filter grille sizing Req's in 150.0(m)13 Exemption From Duct Leakage Requirement s Bypass Duct Status Number of Air Filter Devices on System Can RA3.3 Airflow Protocols be used to test this System? System 1 GREATROO M/KITCHEN Unconditio ned attic R 8 Unconditio ned attic R 8 Not applicable HERS verified fan efficacy (W/cfm) and airflow rate (cfm/ton) None No Bypass Duct 1 Yes Registration Number: 219-P010089040A-000-001-M01001A-0000 Registration Date/Time: 2019-04-17 12:19:18 HERS Provider: CaICERTS CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:25:20 CERTIFICATE OF INSTALLATION CF2R-MCH-01-E Space Conditioning Systems, Ducts, and Fans (Page 12 of 19) J. Installed Duct System Information 01 02 03 04 05 06 07 08 09 10 11 12 SC System Identification or Name SC System Location or Area Served Supply Duct Location Supply Duct R-Value Return Duct Location Return Duct R-Value Exemption from Min R-Value for Ducts In Conditioned Space Method of compliance with duct and filter grille sizing Req's in 150.0(m)13 Exemption From Duct Leakage Requirement s Bypass Duct Status Number of Air Filter Devices on System Can RA3.3 Airflow Protocols be used to test this System? System 2 KITCHEN Unconditio ned attic R-8 Unconditio ned attic R-8 Not applicable HERS verified fan efficacy (W/cfm) and airflow rate (cfm/ton) None No Bypass Duct 1 Yes System 3 MASTER Unconditio ned attic R-8 Unconditio ned attic R-8 Not applicable HERS verified fan efficacy (W/cfm) and airflow rate (cfm/ton) r r--� None '1 No Bypass Duct 1 Yes System 4 LOWER OUTSIDE SUITE Unconditio ned attic R-8 Unconditio ned attic R-8 Not applicable HERS verified fan efficacy (W/cfm) and airflow rate (cfm/ton) None No Bypass Duct 1 Yes Registration Number: 219-P010089040A-000-001-M01001A-0000 Registration Date/Time: 2019-04-17 12:19:18 HERS Provider: CaICERTS CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:25:20 CERTIFICATE OF INSTALLATION CF2R-MCH-01-E Space Conditioning Systems, Ducts, and Fans (Page 13 of 19) J. Installed Duct System Information 01 02 03 04 05 06 07 08 09 10 11 12 SC System Identification or Name SC System Location or Area Served Supply Duct Location Supply Duct R-Value Return Duct Location Return Duct R-Value Exemption from Min R-Value for Ducts In Conditioned Space Method of compliance with duct and filter grille sizing Req's in 150.0(m)13 Exemption From Duct Leakage Requirement s Bypass Duct Status Number of Air Filter Devices on System Can RA3.3 Airflow Protocols be used to test this System? System 5 LOWER INNER SUITE Unconditio ned attic R-8 Unconditio ned attic R-8 Not applicable HERS verified fan efficacy (W/cfm) and airflow rate (cfm/ton) None No Bypass Duct 1 Yes System 6 UPPER POOL SUITE Unconditio ned attic R-8 Unconditio ned attic R-8 Not applicable HERS verified fan efficacy (W/cfm) and airflow rate (cfm/ton) r r--� None '1 No Bypass Duct 1 Yes System 7 UPPER ENTRY SUITE Unconditio ned attic R-8 Unconditio ned attic R-8 Not applicable HERS verified fan efficacy (W/cfm) and airflow rate (cfm/ton) None No Bypass Duct 1 Yes Notes: Registration Number: 219-P010089040A-000-001-M01001A-0000 Registration Date/Time: 2019-04-17 12:19:18 HERS Provider: CaICERTS CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:25:20 CERTIFICATE OF INSTALLATION CF2R-MCH-01-E Space Conditioning Systems, Ducts, and Fans (Page 14 of 19) K. Installed Air Filter Device Information Mandatory requirements for air filter devices are specified Section 150.0(m)12. 01 02 03 04 05 06 07 SC System Identification or Name SC System Location or Area Served Air Filter Device Identification or Name Air Filter Device Type Air Filter Device Location Determined Design Airflow Rate for Air Filter Device (cfm) Determined Design Allowable Pressure Drop for Air Filter Device (inch W.C.) System 1 GREATRO NM/KITCHE FILTER 1 Filter Grille CEILING 2000 0.1 System 2 KITCHEN FILTER 2 Filter Grille CEILING 1200 0.1 System 3 MASTER FILTER 3 Filter Grille CEILING 2000 0.1 System 4 LOWER OUTSIDE SUITE FILTER 4 Filter Grille CEILING 800 0.1 System 5 LOWER INNER SUITE FILTER 5 Filter Grille CEILING 800 0.1 System 6 UPPER POOL SUITE FILTER 6 Filter Grille CEILING 600 0.1 System 7 UPPER ENTRY SUITE FILTER 7 Filter Grille CEILING 800 0.1 Notes: L. Air Filter Device Requirements 01 The system shall be designed to ensure that all recirculated air and all outdoor air supplied to the occupiable space is filtered before passing through the system's thermal conditioning components. Registration Number: 219-P010089040A-000-001-M01001A-0000 Registration Date/Time: 2019-04-17 12:19:18 HERS Provider: CaICERTS CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:25:20 CERTIFICATE OF INSTALLATION CF2R-MCH-01-E Space Conditioning Systems, Ducts, and Fans (Page 15 of 19) L. Air Filter Device Requirements 02 The system shall be designed to accommodate the clean -filter pressure drop imposed by the system air filter device(s). The design airflow rate and maximum allowable clean -filter pressure drop at the design airflow rate applicable to each air filter device shall be determined, and all system air filter device locations shall be labeled to disclose the applicable design airflow rate and the maximum allowable clean -filter pressure drop. The labels shall be permanently affixed to the air filter device, readily legible, and visible to a person replacing the air filter media, and the air filter devices shall be provided with air filter media that conforms to these determined or labeled maximum allowable clean -filter pressure drop values as rated using AHRI Standard 680. 03 All system air filter devices shall be located and installed in such a manner as to allow access and regular service by the system owner. 04 The system shall be provided with air filter media having a designated efficiency equal to or greater than MERV 6 when tested in accordance with ASHRAE Standard 52.2, or a particle size efficiency rating equal to or greater than 50% in the 3.0 to10 µm range when tested in accordance with AHRI Standard 680. 05 The system shall be provided with air filter media that has been labeled by the manufacturer to disclose the efficiency and pressure drop ratings that conform to the required efficiency and pressure drop requirements for the air filter device. The responsible person's signature on this compliance document affirms that all applicable requirements in this table have been met M. HERS Verification Requirements r- 3 I V II Illy • mink -- _ 01 02 03 04 05 06 07 08 09 I 10 11 12 SC System Identificati on or Name SC System Location or Area Served MCH-20 Duct Leakage Test MCH-21 Duct Location Verification MCH-22 AHU Fan Efficacy (W/cfm) MCH-23 AHU Airflow Rate (cfm/ton) MCH-25 Refrigerant Charge MCH-26 Rated SC System Equipment Verification MCH-27 IAQ Mechanical Ventilation MCH-28 Return Duct Design Table 150.0-B or C MCH-29 Supply Duct Surface Area R-Value Buried Ducts MCH30 Ventilation Cooling Credit System 1 GREATROO M/KITCHEN Yes No Yes Yes No Yes Yes No No No System 2 KITCHEN Yes No Yes Yes No Yes Yes No No No System 3 MASTER Yes No Yes Yes No Yes Yes No No No Registration Number: 219-P010089040A-000-001-M01001A-0000 Registration Date/Time: 2019-04-17 12:19:18 HERS Provider: CaICERTS CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:25:20 CERTIFICATE OF INSTALLATION CF2R-MCH-01-E Space Conditioning Systems, Ducts, and Fans (Page 16 of 19) M. HERS Verification Requirements 01 02 03 04 05 06 07 08 09 10 11 12 SC System Identificati on or Name SC System Location or Area Served MCH-20 Duct Leaka a g Test MCH-21 Duct Location Verification MCH-22 AHU Fan Efficacy (W/cfm) MCH-23 AHU Airflow Rate (cfm/ton) MCH-25 Refrigerant Charge g MCH-26 Rated SC System Equipment Verification MCH-27 IAQ Mechanical Ventilation MCH-28 Return Duct Design Table 150.0-B or C MCH-29 Supply Duct Surface Area R-Value Buried Ducts MCH30 Ventilation Cooling Credit System 4 LOWER OUTSIDE SUITE Yes No Yes Yes No Yes Yes No No No System 5 LOWER INNER SUITE Yes No Yes Yes No Yes Yes No No No System 6 UPPER POOL SUITE Yes No Yes Yes Yes Yes Yes No No No System 7 UPPER ENTRY SUITE Yes No Yes Yes Yes Yes Yes No No No Notes: Registration Number: 219-P010089040A-000-001-M01001A-0000 Registration Date/Time: 2019-04-17 12:19:18 HERS Provider: CaICERTS CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version: 2018.0.001 Report Generated: 2019-04-17 11:25:20 Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-01-E Space Conditioning Systems, Ducts, and Fans (Page 17 of 19) N. Space Conditioning Systems, Ducts and Fans -Mandatory Requirements and Additional Measures Note: Additional mandatory requirements from Section 150.0 that are not listed here may be applicable to some systems. These requirements may be applicable to only newly installed equipment or portions of the system that are altered. Existing equipment may be exempt from these requirements. Heating Equipment 01 Equipment Efficiency: All heating equipment must meet the minimum efficiency requirements of Section 110.1 and Section 110.2(a) and the Appliance Efficiency Regulations. 02 Controls: All unitary heating systems, including heat pumps, must be controlled by a setback thermostat. These thermostats must be capable of allowing the occupant to program the temperature set points for at least four different periods in 24 hours. See Sections 150.0(i), 110.2(b). 03 Sizing: Heating load calculations must be done on portions of the building served by new heating systems to prevent inadvertent undersizing or oversizing. See sections 150.0(h)1 and 2). 04 Furnace Temperature Rise: Central forced -air heating furnace installations must be configured to operate at or below the furnace manufacturer's maximum inlet -to -outlet temperature rise specification. See Section 150.0(h)4. 05 Standby Losses and Pilot Lights: Fan -type central furnaces may not have a continuously burning pilot light. Section 110.5 and Section 110.2(d). Cooling Equipment 06 Equipment Efficiency: All cooling equipment must meet the minimum efficiency requirements of Section 110.1 and Section 110.2(a) and the Appliance Efficiency Regulations. 07 Refrigerant Line Insulation: All refrigerant line insulation in split system air conditioners and heat pumps must meet the R-value and protection requirements of Section 150.0(j)2 and 3, and Section 150.0(m)9. 08 Condensing Unit Location: Condensing units shall not be placed within five (5) feet of a dryer vent outlet. See Section 150.0(h)3A. 09 Liquid Line Filter Drier: If applicable, a liquid line filter drier shall be installed according to the manufacturer's specifications. Section 150.0(h)3B 10 Sizing: Cooling load calculations must be done on portions of the building served by new cooling systems to prevent inadvertent undersizing or oversizing. See Section 150.0(h)1 and 2. Air Distribution System Ducts, Plenums and Fans Registration Number: 219-P010089040A-000-001-M01001A-0000 Registration Date/Time: 2019-04-17 12:19:18 HERS Provider: CaICERTS CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:25:20 CERTIFICATE OF INSTALLATION CF2R-MCH-01-E Space Conditioning Systems, Ducts, and Fans (Page 18 of 19) N. Space Conditioning Systems, Ducts and Fans -Mandatory Requirements and Additional Measures Note Additional mandatory requirements from Section 150.0 that are not listed here may be applicable to some systems. These requirements may be applicable to only newly installed equipment or portions of the system that are altered. Existing equipment may be exempt from these requirements. 11 Insulation: In all cases, unless ducts are enclosed entirely in directly conditioned space, the minimum duct insulation value is R-6. Note that higher values may be required by the prescriptive or performance requirements. See Section 150.0(m)1. 12 Connections and Closures: All installed air -distribution system ducts and plenums must be, sealed and insulated to meet the requirements of CMC Sections 601.0, 602.0, 603.0, 604.0, 605.0 and ANSI/SMACNA-006-2006: Supply -air and return -air ducts and plenums must be insulated to a minimum installed level of R-6.0 or enclosed entirely in directly conditioned space as confirmed through field verification and diagnostic testing in accordance with the requirements of Reference Residential Appendix RA3.1.4.3.8. Heat Pump Thermostat 13 A thermostat shall be installed that meets the requirements of Section 110.2(b) and Section 110.2(c). 14 The thermostat shall be installed in accordance with the manufacturers published installation specifications 15 First stage of heating shall be assigned to heat pump heating. 16 Second stage back up heating shall be set to come on only when the indoor set temperature cannot be met. The responsible person's signature on this compliance document affirms that all applicable requirements in this table have been met. Registration Number: 219-P010089040A-000-001-M01001A-0000 Registration Date/Time: 2019-04-17 12:19:18 HERS Provider: CaICERTS CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version: 2018.0.001 Report Generated: 2019-04-17 11:25:20 Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-01-E Space Conditioning Systems, Ducts, and Fans (Page 19 of 19) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 4‘L1SllLfl/ �`Z in 64a- Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:18 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation, and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I will ensure that a registered copy of this Certificate of Installation shall be posted or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: LLI y7 Gas*; Pa/eedea- Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:18 Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: 219-P010089040A-000-001-M01001A-0000 Registration Date/Time: 2019-04-17 12:19:18 HERS Provider: CaICERTS CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version: 2018.0.001 Report Generated: 2019-04-17 11:25:20 Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-20-H Duct Leakage Diagnostic Test (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. System Information 01 Space Conditioning System Identification or Name System 1 02 Space Conditioning System Location or Area Served GREATROOM/KITCHEN 03 Building Type from CF-1R Single family 04 Verified Low Leakage Ducts in Conditioned Space (VLLDCS) Credit from CF1R? No, credit is not taken 05 Verified Low Leakage Air Handling Unit (VLLAHU) Credit from CF1R? No, credit is not taken 06 Duct System Compliance Category New MCH-20a - Completely New Duct System B. Duct Leakage Diagnostic Test 01 Condenser Nominal Cooling Capacity (ton) 5 02 Heating Capacity (kBtu/h) 64 03 Conditioned Floor Area Served by this HVAC System (ft2) 1000 04 Duct Leakage Test Conditions Test final 05 Duct Leakage Test Method Total leakage 06 Leakage Factor 0.05 07 Air Handling Unit Airflow (AHUAirflow) Determination Method Cooling system method 08 Measured AHUAirflow (cfm) This field or section is not applicable 09 Calculated Target Allowable Duct Leakage (cfm) 100 10 Actual Duct Leakage Rate from Leakage Test Measurement (cfm) 99 11 Compliance Statement System passes leakage test Registration Number: 219-P010089040A-000-001-M20002A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Report Generated: 2019-04-17 11:26:33 Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-20-H Duct Leakage Diagnostic Test (Page 2 of 3) C. Additional Requirements for Compliance 01 System was tested in its normal operation condition. No temporary taping allowed. 02 Outside air (OA) duct connections to the central forced air duct system shall not be sealed/taped off during duct leakage testing. OA ducts used for Central Fan Integrated (CFI) Indoor Air Quality ventilation systems, or Central Fan Ventilation Cooling Systems, that utilize dampers that open only when OA is required and automatically close when OA is not required, may configure the OA damper to the closed position during duct leakage testing. 03 All supply and return register boots were sealed to the drywall. 04 Building cavities were not used as plenums or platform returns in lieu of ducts. 05 If cloth backed tape was used it was covered with Mastic and draw bands. 06 All connection points between the air handler and the supply and return plenums are completely sealed. Visual Inspection at Final Construction Stage (applicable if system was tested at rough -in). After installing the interior finishing wall and verifying that the above rough -in tests was completed, the following procedure must be performed 07 For all supply and return registers, verify that the spaces between the register boot and the interior finishing wall are properly sealed. 08 If the house rough -in duct leakage test was conducted without an air handler installed, inspect the connection points between the air handler and the supply and return plenums to verify that the connection points are properly sealed. 09 Inspect all joints to ensure that no cloth backed rubber adhesive duct tape is used. The responsible person's signature on this compliance document affirms that all applicable requirements in this table have been met. Registration Number: 219-P010089040A-000-001-M20002A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:26:33 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-20-H Duct Leakage Diagnostic Test (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:19 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:19 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M20002A-0000 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:26:33 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-20-H Duct Leakage Diagnostic Test (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. System Information 01 Space Conditioning System Identification or Name System 2 02 Space Conditioning System Location or Area Served KITCHEN 03 Building Type from CF-1R Single family 04 Verified Low Leakage Ducts in Conditioned Space (VLLDCS) Credit from CF1R? No, credit is not taken 05 Verified Low Leakage Air Handling Unit (VLLAHU) Credit from CF1R? No, credit is not taken 06 Duct System Compliance Category New MCH-20a - Completely New Duct System B. Duct Leakage Diagnostic Test 01 Condenser Nominal Cooling Capacity (ton) 3 02 Heating Capacity (kBtu/h) 64 03 Conditioned Floor Area Served by this HVAC System (ft2) 1000 04 Duct Leakage Test Conditions Test final 05 Duct Leakage Test Method Total leakage 06 Leakage Factor 0.05 07 Air Handling Unit Airflow (AHUAirflow) Determination Method Cooling system method 08 Measured AHUAirflow (cfm) This field or section is not applicable 09 Calculated Target Allowable Duct Leakage (cfm) 60 10 Actual Duct Leakage Rate from Leakage Test Measurement (cfm) 53 11 Compliance Statement System passes leakage test Registration Number: 219-P010089040A-000-001-M20003A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Report Generated: 2019-04-17 11:30:55 Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-20-H Duct Leakage Diagnostic Test (Page 2 of 3) C. Additional Requirements for Compliance 01 System was tested in its normal operation condition. No temporary taping allowed. 02 Outside air (OA) duct connections to the central forced air duct system shall not be sealed/taped off during duct leakage testing. OA ducts used for Central Fan Integrated (CFI) Indoor Air Quality ventilation systems, or Central Fan Ventilation Cooling Systems, that utilize dampers that open only when OA is required and automatically close when OA is not required, may configure the OA damper to the closed position during duct leakage testing. 03 All supply and return register boots were sealed to the drywall. 04 Building cavities were not used as plenums or platform returns in lieu of ducts. 05 If cloth backed tape was used it was covered with Mastic and draw bands. 06 All connection points between the air handler and the supply and return plenums are completely sealed. Visual Inspection at Final Construction Stage (applicable if system was tested at rough -in). After installing the interior finishing wall and verifying that the above rough -in tests was completed, the following procedure must be performed 07 For all supply and return registers, verify that the spaces between the register boot and the interior finishing wall are properly sealed. 08 If the house rough -in duct leakage test was conducted without an air handler installed, inspect the connection points between the air handler and the supply and return plenums to verify that the connection points are properly sealed. 09 Inspect all joints to ensure that no cloth backed rubber adhesive duct tape is used. The responsible person's signature on this compliance document affirms that all applicable requirements in this table have been met. Registration Number: 219-P010089040A-000-001-M20003A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:30:55 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-20-H Duct Leakage Diagnostic Test (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:19 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:19 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M20003A-0000 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:30:55 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-20-H Duct Leakage Diagnostic Test (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. System Information 01 Space Conditioning System Identification or Name System 3 02 Space Conditioning System Location or Area Served MASTER 03 Building Type from CF-1R Single family 04 Verified Low Leakage Ducts in Conditioned Space (VLLDCS) Credit from CF1R? No, credit is not taken 05 Verified Low Leakage Air Handling Unit (VLLAHU) Credit from CF1R? No, credit is not taken 06 Duct System Compliance Category New MCH-20a - Completely New Duct System B. Duct Leakage Diagnostic Test 01 Condenser Nominal Cooling Capacity (ton) 5 02 Heating Capacity (kBtu/h) 64 03 Conditioned Floor Area Served by this HVAC System (ft2) 827 04 Duct Leakage Test Conditions Test final 05 Duct Leakage Test Method Total leakage 06 Leakage Factor 0.05 07 Air Handling Unit Airflow (AHUAirflow) Determination Method Cooling system method 08 Measured AHUAirflow (cfm) This field or section is not applicable 09 Calculated Target Allowable Duct Leakage (cfm) 100 10 Actual Duct Leakage Rate from Leakage Test Measurement (cfm) 80 11 Compliance Statement System passes leakage test Registration Number: 219-P010089040A-000-001-M20004A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Report Generated: 2019-04-17 11:32:45 Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-20-H Duct Leakage Diagnostic Test (Page 2 of 3) C. Additional Requirements for Compliance 01 System was tested in its normal operation condition. No temporary taping allowed. 02 Outside air (OA) duct connections to the central forced air duct system shall not be sealed/taped off during duct leakage testing. OA ducts used for Central Fan Integrated (CFI) Indoor Air Quality ventilation systems, or Central Fan Ventilation Cooling Systems, that utilize dampers that open only when OA is required and automatically close when OA is not required, may configure the OA damper to the closed position during duct leakage testing. 03 All supply and return register boots were sealed to the drywall. 04 Building cavities were not used as plenums or platform returns in lieu of ducts. 05 If cloth backed tape was used it was covered with Mastic and draw bands. 06 All connection points between the air handler and the supply and return plenums are completely sealed. Visual Inspection at Final Construction Stage (applicable if system was tested at rough -in). After installing the interior finishing wall and verifying that the above rough -in tests was completed, the following procedure must be performed 07 For all supply and return registers, verify that the spaces between the register boot and the interior finishing wall are properly sealed. 08 If the house rough -in duct leakage test was conducted without an air handler installed, inspect the connection points between the air handler and the supply and return plenums to verify that the connection points are properly sealed. 09 Inspect all joints to ensure that no cloth backed rubber adhesive duct tape is used. The responsible person's signature on this compliance document affirms that all applicable requirements in this table have been met. Registration Number: 219-P010089040A-000-001-M20004A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:32:45 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-20-H Duct Leakage Diagnostic Test (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:19 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:19 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M20004A-0000 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:32:45 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-20-H Duct Leakage Diagnostic Test (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. System Information 01 Space Conditioning System Identification or Name System 4 02 Space Conditioning System Location or Area Served LOWER OUTSIDE SUITE 03 Building Type from CF-1R Single family 04 Verified Low Leakage Ducts in Conditioned Space (VLLDCS) Credit from CF1R? No, credit is not taken 05 Verified Low Leakage Air Handling Unit (VLLAHU) Credit from CF1R? No, credit is not taken 06 Duct System Compliance Category New MCH-20a - Completely New Duct System B. Duct Leakage Diagnostic Test 01 Condenser Nominal Cooling Capacity (ton) 2 02 Heating Capacity (kBtu/h) 0 03 Conditioned Floor Area Served by this HVAC System (ft2) 675 04 Duct Leakage Test Conditions Test final 05 Duct Leakage Test Method Total leakage 06 Leakage Factor 0.05 07 Air Handling Unit Airflow (AHUAirflow) Determination Method Cooling system method 08 Measured AHUAirflow (cfm) This field or section is not applicable 09 Calculated Target Allowable Duct Leakage (cfm) 40 10 Actual Duct Leakage Rate from Leakage Test Measurement (cfm) 38 11 Compliance Statement System passes leakage test Registration Number: 219-P010089040A-000-001-M20005A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Report Generated: 2019-04-17 11:35:20 Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-20-H Duct Leakage Diagnostic Test (Page 2 of 3) C. Additional Requirements for Compliance 01 System was tested in its normal operation condition. No temporary taping allowed. 02 Outside air (OA) duct connections to the central forced air duct system shall not be sealed/taped off during duct leakage testing. OA ducts used for Central Fan Integrated (CFI) Indoor Air Quality ventilation systems, or Central Fan Ventilation Cooling Systems, that utilize dampers that open only when OA is required and automatically close when OA is not required, may configure the OA damper to the closed position during duct leakage testing. 03 All supply and return register boots were sealed to the drywall. 04 Building cavities were not used as plenums or platform returns in lieu of ducts. 05 If cloth backed tape was used it was covered with Mastic and draw bands. 06 All connection points between the air handler and the supply and return plenums are completely sealed. Visual Inspection at Final Construction Stage (applicable if system was tested at rough -in). After installing the interior finishing wall and verifying that the above rough -in tests was completed, the following procedure must be performed 07 For all supply and return registers, verify that the spaces between the register boot and the interior finishing wall are properly sealed. 08 If the house rough -in duct leakage test was conducted without an air handler installed, inspect the connection points between the air handler and the supply and return plenums to verify that the connection points are properly sealed. 09 Inspect all joints to ensure that no cloth backed rubber adhesive duct tape is used. The responsible person's signature on this compliance document affirms that all applicable requirements in this table have been met. Registration Number: 219-P010089040A-000-001-M20005A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:35:20 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-20-H Duct Leakage Diagnostic Test (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:19 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:19 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M20005A-0000 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:35:20 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-20-H Duct Leakage Diagnostic Test (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. System Information 01 Space Conditioning System Identification or Name System 5 02 Space Conditioning System Location or Area Served LOWER INNER SUITE 03 Building Type from CF-1R Single family 04 Verified Low Leakage Ducts in Conditioned Space (VLLDCS) Credit from CF1R? No, credit is not taken 05 Verified Low Leakage Air Handling Unit (VLLAHU) Credit from CF1R? No, credit is not taken 06 Duct System Compliance Category New MCH-20a - Completely New Duct System B. Duct Leakage Diagnostic Test 01 Condenser Nominal Cooling Capacity (ton) 1.5 02 Heating Capacity (kBtu/h) 0 03 Conditioned Floor Area Served by this HVAC System (ft2) 675 04 Duct Leakage Test Conditions Test final 05 Duct Leakage Test Method Total leakage 06 Leakage Factor 0.05 07 Air Handling Unit Airflow (AHUAirflow) Determination Method Cooling system method 08 Measured AHUAirflow (cfm) This field or section is not applicable 09 Calculated Target Allowable Duct Leakage (cfm) 30 10 Actual Duct Leakage Rate from Leakage Test Measurement (cfm) 27 11 Compliance Statement System passes leakage test Registration Number: 219-P010089040A-000-001-M20006A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CalCERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Report Generated: 2019-04-17 11:37:04 Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-20-H Duct Leakage Diagnostic Test (Page 2 of 3) C. Additional Requirements for Compliance 01 System was tested in its normal operation condition. No temporary taping allowed. 02 Outside air (OA) duct connections to the central forced air duct system shall not be sealed/taped off during duct leakage testing. OA ducts used for Central Fan Integrated (CFI) Indoor Air Quality ventilation systems, or Central Fan Ventilation Cooling Systems, that utilize dampers that open only when OA is required and automatically close when OA is not required, may configure the OA damper to the closed position during duct leakage testing. 03 All supply and return register boots were sealed to the drywall. 04 Building cavities were not used as plenums or platform returns in lieu of ducts. 05 If cloth backed tape was used it was covered with Mastic and draw bands. 06 All connection points between the air handler and the supply and return plenums are completely sealed. Visual Inspection at Final Construction Stage (applicable if system was tested at rough -in). After installing the interior finishing wall and verifying that the above rough -in tests was completed, the following procedure must be performed 07 For all supply and return registers, verify that the spaces between the register boot and the interior finishing wall are properly sealed. 08 If the house rough -in duct leakage test was conducted without an air handler installed, inspect the connection points between the air handler and the supply and return plenums to verify that the connection points are properly sealed. 09 Inspect all joints to ensure that no cloth backed rubber adhesive duct tape is used. The responsible person's signature on this compliance document affirms that all applicable requirements in this table have been met. Registration Number: 219-P010089040A-000-001-M20006A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CalCERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:37:04 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-20-H Duct Leakage Diagnostic Test (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:19 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:19 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M20006A-0000 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:37:04 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-20-H Duct Leakage Diagnostic Test (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. System Information 01 Space Conditioning System Identification or Name System 6 02 Space Conditioning System Location or Area Served UPPER POOL SUITE 03 Building Type from CF-1R Single family 04 Verified Low Leakage Ducts in Conditioned Space (VLLDCS) Credit from CF1R? No, credit is not taken 05 Verified Low Leakage Air Handling Unit (VLLAHU) Credit from CF1R? No, credit is not taken 06 Duct System Compliance Category New MCH-20a - Completely New Duct System B. Duct Leakage Diagnostic Test 01 Condenser Nominal Cooling Capacity (ton) 2 02 Heating Capacity (kBtu/h) 0 03 Conditioned Floor Area Served by this HVAC System (ft2) 675 04 Duct Leakage Test Conditions Test final 05 Duct Leakage Test Method Total leakage 06 Leakage Factor 0.05 07 Air Handling Unit Airflow (AHUAirflow) Determination Method Cooling system method 08 Measured AHUAirflow (cfm) This field or section is not applicable 09 Calculated Target Allowable Duct Leakage (cfm) 40 10 Actual Duct Leakage Rate from Leakage Test Measurement (cfm) 37 11 Compliance Statement System passes leakage test Registration Number: 219-P010089040A-000-001-M20007A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CalCERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Report Generated: 2019-04-17 11:40:04 Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-20-H Duct Leakage Diagnostic Test (Page 2 of 3) C. Additional Requirements for Compliance 01 System was tested in its normal operation condition. No temporary taping allowed. 02 Outside air (OA) duct connections to the central forced air duct system shall not be sealed/taped off during duct leakage testing. OA ducts used for Central Fan Integrated (CFI) Indoor Air Quality ventilation systems, or Central Fan Ventilation Cooling Systems, that utilize dampers that open only when OA is required and automatically close when OA is not required, may configure the OA damper to the closed position during duct leakage testing. 03 All supply and return register boots were sealed to the drywall. 04 Building cavities were not used as plenums or platform returns in lieu of ducts. 05 If cloth backed tape was used it was covered with Mastic and draw bands. 06 All connection points between the air handler and the supply and return plenums are completely sealed. Visual Inspection at Final Construction Stage (applicable if system was tested at rough -in). After installing the interior finishing wall and verifying that the above rough -in tests was completed, the following procedure must be performed 07 For all supply and return registers, verify that the spaces between the register boot and the interior finishing wall are properly sealed. 08 If the house rough -in duct leakage test was conducted without an air handler installed, inspect the connection points between the air handler and the supply and return plenums to verify that the connection points are properly sealed. 09 Inspect all joints to ensure that no cloth backed rubber adhesive duct tape is used. The responsible person's signature on this compliance document affirms that all applicable requirements in this table have been met. Registration Number: 219-P010089040A-000-001-M20007A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CalCERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:40:04 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-20-H Duct Leakage Diagnostic Test (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:19 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:19 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M20007A-0000 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:40:04 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-20-H Duct Leakage Diagnostic Test (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. System Information 01 Space Conditioning System Identification or Name System 7 02 Space Conditioning System Location or Area Served UPPER ENTRY SUITE 03 Building Type from CF-1R Single family 04 Verified Low Leakage Ducts in Conditioned Space (VLLDCS) Credit from CF1R? No, credit is not taken 05 Verified Low Leakage Air Handling Unit (VLLAHU) Credit from CF1R? No, credit is not taken 06 Duct System Compliance Category New MCH-20a - Completely New Duct System B. Duct Leakage Diagnostic Test 01 Condenser Nominal Cooling Capacity (ton) 2 02 Heating Capacity (kBtu/h) 0 03 Conditioned Floor Area Served by this HVAC System (ft2) 675 04 Duct Leakage Test Conditions Test final 05 Duct Leakage Test Method Total leakage 06 Leakage Factor 0.05 07 Air Handling Unit Airflow (AHUAirflow) Determination Method Cooling system method 08 Measured AHUAirflow (cfm) This field or section is not applicable 09 Calculated Target Allowable Duct Leakage (cfm) 40 10 Actual Duct Leakage Rate from Leakage Test Measurement (cfm) 34 11 Compliance Statement System passes leakage test Registration Number: 219-P010089040A-000-001-M20008A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Report Generated: 2019-04-17 11:50:58 Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-20-H Duct Leakage Diagnostic Test (Page 2 of 3) C. Additional Requirements for Compliance 01 System was tested in its normal operation condition. No temporary taping allowed. 02 Outside air (OA) duct connections to the central forced air duct system shall not be sealed/taped off during duct leakage testing. OA ducts used for Central Fan Integrated (CFI) Indoor Air Quality ventilation systems, or Central Fan Ventilation Cooling Systems, that utilize dampers that open only when OA is required and automatically close when OA is not required, may configure the OA damper to the closed position during duct leakage testing. 03 All supply and return register boots were sealed to the drywall. 04 Building cavities were not used as plenums or platform returns in lieu of ducts. 05 If cloth backed tape was used it was covered with Mastic and draw bands. 06 All connection points between the air handler and the supply and return plenums are completely sealed. Visual Inspection at Final Construction Stage (applicable if system was tested at rough -in). After installing the interior finishing wall and verifying that the above rough -in tests was completed, the following procedure must be performed 07 For all supply and return registers, verify that the spaces between the register boot and the interior finishing wall are properly sealed. 08 If the house rough -in duct leakage test was conducted without an air handler installed, inspect the connection points between the air handler and the supply and return plenums to verify that the connection points are properly sealed. 09 Inspect all joints to ensure that no cloth backed rubber adhesive duct tape is used. The responsible person's signature on this compliance document affirms that all applicable requirements in this table have been met. Registration Number: 219-P010089040A-000-001-M20008A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:50:58 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-20-H Duct Leakage Diagnostic Test (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:19 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:19 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M20008A-0000 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:50:58 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-23-H Space Conditioning System Airflow Rate (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. Ducted Cooling System Information 01 System Identification or Name System 1 02 System Location or Area Served GREATROOM/KITCHEN 03 System Installation Type New 04 Nominal Cooling Capacity (tons) of Condenser 5 05 Condenser Speed Type Multi -speed 06 Cooling System Zonal Control Type Not Zonal 07 Central Fan Integrated (CFI) Ventilation System Status Not a CFI system 08 System Bypass Duct Status No Bypass Duct 09 Date of System Airflow Rate Measurement 2019-04-08 10 Airflow Rate Protocol Utilized RA3.3 procedures for airflow rate measurement B. Hole for the placement of a Static Pressure Probe (HSPP), and Permanently Installed Static Pressure Probe (PSPP) in the Supply Plenum. Procedures for installing HSPP or PSPP are specified in RA3.3.1.1. 01 Method Used to Demonstrate Compliance with the HSPP/PSPP Requirement HSPP installed and labeled consistent with Figure RA3.3-1 C. Airflow Rate Measurement Apparatus and Procedure Information Instrument Specifications are given in RA3.3.1.1, and system airflow rate measurement apparatus information is given in RA3.3.2. 01 Airflow Rate Measurement Type used for this airflow rate verification. Traditional Flow Capture Hood according to procedure in RA3.3.3.1.4 02 Manufacturer of Airflow Measurement Apparatus ALNOR 03 Model number of Airflow Measurement Apparatus EBT731 04 Certification Status of the Airflow Measurement Apparatus Accuracy Certified by Manufacturer and listed on CEC Website at http://www.energy.ca.gov/title24/equipment_cert/ama_fas /index.html Registration Number: 219-P010089040A-000-001-M23002A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CalCERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2016.2.000 Report Generated: 2019-04-17 11:27:03 Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-23-H Space Conditioning System Airflow Rate (Page 2 of 3) MCH-23a Forced Air System Airflow Rate Measurement - Newly Installed Non -Zoned Systems or Zoned Multi -Speed Compressor D. Forced Air System Airflow Rate Measurement The procedures for System Airflow Rate Verification are specified in Reference Residential Appendix RA3.3. 01 Required Minimum System Airflow Rate (cfm/ton) 350 02 Required Minimum System Airflow Target (cfm) 1750 03 Actual System Airflow Rate Measurement (cfm) 1773 04 Compliance Statement: System airflow rate complies E. Additional Requirements 01 Air filters that meet the applicable requirements of Standards Section 150.0(m)12 or 150.0(m)13 were properly installed in the system during system air flow rate measurement identified on this Certificate of Installation. 02 The airflow rate measurement apparatus used to perform the airflow rate measurement identified on this Certificate of Installation was calibrated in accordance with the apparatus manufacturer's specifications and conforms to the instrumentation specifications given in RA3.3.1. 03 A visual inspection shall confirm that bypass ducts that deliver conditioned supply air directly to the space conditioning system return duct airflow are not used on newly constructed zonally controlled systems unless the Performance Certificate of Compliance indicates an allowance for use of a bypass duct. When a bypass duct is accounted for on the Performance Certificate of Compliance, the airflow rate shall conform to the specifications listed on the Certificate of Compliance. 04 All registers were fully open during the diagnostic test. 05 System fan was set at maximum speed during the diagnostic test. 06 If fresh air duct is part of the HVAC system it was not closed during the diagnostic test. 07 Airflow rate and fan watt draw shall be simultaneous measurements when used to calculate the Fan Efficacy tested value. 08 Multi -speed compressor space cooling systems or variable speed compressor systems shall verify air flow (cfm/ton) and fan efficacy (Watt/cfm) with system operating in cooling mode at the maximum compressor speed and the maximum air handler fan speed. The responsible person's signature on this compliance document affirms that all applicable requirements in this table have been met. Registration Number: 219-P010089040A-000-001-M23002A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CalCERTS CA Building Energy Efficiency Standards Report Version: 2016.2.000 Report Generated: 2019-04-17 11:27:03 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-23-H Space Conditioning System Airflow Rate (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:19 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:19 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M23002A-0000 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2016.2.000 Report Generated: 2019-04-17 11:27:03 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-23-H Space Conditioning System Airflow Rate (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. Ducted Cooling System Information 01 System Identification or Name System 2 02 System Location or Area Served KITCHEN 03 System Installation Type New 04 Nominal Cooling Capacity (tons) of Condenser 3 05 Condenser Speed Type Multi -speed 06 Cooling System Zonal Control Type Not Zonal 07 Central Fan Integrated (CFI) Ventilation System Status Not a CFI system 08 System Bypass Duct Status No Bypass Duct 09 Date of System Airflow Rate Measurement 2019-04-08 10 Airflow Rate Protocol Utilized RA3.3 procedures for airflow rate measurement B. Hole for the placement of a Static Pressure Probe (HSPP), and Permanently Installed Static Pressure Probe (PSPP) in the Supply Plenum. Procedures for installing HSPP or PSPP are specified in RA3.3.1.1. 01 Method Used to Demonstrate Compliance with the HSPP/PSPP Requirement HSPP installed and labeled consistent with Figure RA3.3-1 C. Airflow Rate Measurement Apparatus and Procedure Information Instrument Specifications are given in RA3.3.1.1, and system airflow rate measurement apparatus information is given in RA3.3.2. 01 Airflow Rate Measurement Type used for this airflow rate verification. Traditional Flow Capture Hood according to procedure in RA3.3.3.1.4 02 Manufacturer of Airflow Measurement Apparatus ALNOR 03 Model number of Airflow Measurement Apparatus EBT731 04 Certification Status of the Airflow Measurement Apparatus Accuracy Certified by Manufacturer and listed on CEC Website at http://www.energy.ca.gov/title24/equipment_cert/ama_fas /index.html Registration Number: 219-P010089040A-000-001-M23003A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CalCERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2016.2.000 Report Generated: 2019-04-17 11:31:25 Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-23-H Space Conditioning System Airflow Rate (Page 2 of 3) MCH-23a Forced Air System Airflow Rate Measurement - Newly Installed Non -Zoned Systems or Zoned Multi -Speed Compressor D. Forced Air System Airflow Rate Measurement The procedures for System Airflow Rate Verification are specified in Reference Residential Appendix RA3.3. 01 Required Minimum System Airflow Rate (cfm/ton) 350 02 Required Minimum System Airflow Target (cfm) 1050 03 Actual System Airflow Rate Measurement (cfm) 1104 04 Compliance Statement: System airflow rate complies E. Additional Requirements 01 Air filters that meet the applicable requirements of Standards Section 150.0(m)12 or 150.0(m)13 were properly installed in the system during system air flow rate measurement identified on this Certificate of Installation. 02 The airflow rate measurement apparatus used to perform the airflow rate measurement identified on this Certificate of Installation was calibrated in accordance with the apparatus manufacturer's specifications and conforms to the instrumentation specifications given in RA3.3.1. 03 A visual inspection shall confirm that bypass ducts that deliver conditioned supply air directly to the space conditioning system return duct airflow are not used on newly constructed zonally controlled systems unless the Performance Certificate of Compliance indicates an allowance for use of a bypass duct. When a bypass duct is accounted for on the Performance Certificate of Compliance, the airflow rate shall conform to the specifications listed on the Certificate of Compliance. 04 All registers were fully open during the diagnostic test. 05 System fan was set at maximum speed during the diagnostic test. 06 If fresh air duct is part of the HVAC system it was not closed during the diagnostic test. 07 Airflow rate and fan watt draw shall be simultaneous measurements when used to calculate the Fan Efficacy tested value. 08 Multi -speed compressor space cooling systems or variable speed compressor systems shall verify air flow (cfm/ton) and fan efficacy (Watt/cfm) with system operating in cooling mode at the maximum compressor speed and the maximum air handler fan speed. The responsible person's signature on this compliance document affirms that all applicable requirements in this table have been met. Registration Number: 219-P010089040A-000-001-M23003A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2016.2.000 Report Generated: 2019-04-17 11:31:25 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-23-H Space Conditioning System Airflow Rate (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:19 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:19 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M23003A-0000 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2016.2.000 Report Generated: 2019-04-17 11:31:25 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-23-H Space Conditioning System Airflow Rate (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. Ducted Cooling System Information 01 System Identification or Name System 3 02 System Location or Area Served MASTER 03 System Installation Type New 04 Nominal Cooling Capacity (tons) of Condenser 5 05 Condenser Speed Type Multi -speed 06 Cooling System Zonal Control Type Not Zonal 07 Central Fan Integrated (CFI) Ventilation System Status Not a CFI system 08 System Bypass Duct Status No Bypass Duct 09 Date of System Airflow Rate Measurement 2019-04-08 10 Airflow Rate Protocol Utilized RA3.3 procedures for airflow rate measurement B. Hole for the placement of a Static Pressure Probe (HSPP), and Permanently Installed Static Pressure Probe (PSPP) in the Supply Plenum. Procedures for installing HSPP or PSPP are specified in RA3.3.1.1. 01 Method Used to Demonstrate Compliance with the HSPP/PSPP Requirement HSPP installed and labeled consistent with Figure RA3.3-1 C. Airflow Rate Measurement Apparatus and Procedure Information Instrument Specifications are given in RA3.3.1.1, and system airflow rate measurement apparatus information is given in RA3.3.2. 01 Airflow Rate Measurement Type used for this airflow rate verification. Traditional Flow Capture Hood according to procedure in RA3.3.3.1.4 02 Manufacturer of Airflow Measurement Apparatus ALNOR 03 Model number of Airflow Measurement Apparatus EBT731 04 Certification Status of the Airflow Measurement Apparatus Accuracy Certified by Manufacturer and listed on CEC Website at http://www.energy.ca.gov/title24/equipment_cert/ama_fas /index.html Registration Number: 219-P010089040A-000-001-M23004A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CalCERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2016.2.000 Report Generated: 2019-04-17 11:33:17 Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-23-H Space Conditioning System Airflow Rate (Page 2 of 3) MCH-23a Forced Air System Airflow Rate Measurement - Newly Installed Non -Zoned Systems or Zoned Multi -Speed Compressor D. Forced Air System Airflow Rate Measurement The procedures for System Airflow Rate Verification are specified in Reference Residential Appendix RA3.3. 01 Required Minimum System Airflow Rate (cfm/ton) 350 02 Required Minimum System Airflow Target (cfm) 1750 03 Actual System Airflow Rate Measurement (cfm) 1791 04 Compliance Statement: System airflow rate complies E. Additional Requirements 01 Air filters that meet the applicable requirements of Standards Section 150.0(m)12 or 150.0(m)13 were properly installed in the system during system air flow rate measurement identified on this Certificate of Installation. 02 The airflow rate measurement apparatus used to perform the airflow rate measurement identified on this Certificate of Installation was calibrated in accordance with the apparatus manufacturer's specifications and conforms to the instrumentation specifications given in RA3.3.1. 03 A visual inspection shall confirm that bypass ducts that deliver conditioned supply air directly to the space conditioning system return duct airflow are not used on newly constructed zonally controlled systems unless the Performance Certificate of Compliance indicates an allowance for use of a bypass duct. When a bypass duct is accounted for on the Performance Certificate of Compliance, the airflow rate shall conform to the specifications listed on the Certificate of Compliance. 04 All registers were fully open during the diagnostic test. 05 System fan was set at maximum speed during the diagnostic test. 06 If fresh air duct is part of the HVAC system it was not closed during the diagnostic test. 07 Airflow rate and fan watt draw shall be simultaneous measurements when used to calculate the Fan Efficacy tested value. 08 Multi -speed compressor space cooling systems or variable speed compressor systems shall verify air flow (cfm/ton) and fan efficacy (Watt/cfm) with system operating in cooling mode at the maximum compressor speed and the maximum air handler fan speed. The responsible person's signature on this compliance document affirms that all applicable requirements in this table have been met. Registration Number: 219-P010089040A-000-001-M23004A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2016.2.000 Report Generated: 2019-04-17 11:33:17 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-23-H Space Conditioning System Airflow Rate (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:19 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:19 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M23004A-0000 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2016.2.000 Report Generated: 2019-04-17 11:33:17 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-23-H Space Conditioning System Airflow Rate (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. Ducted Cooling System Information 01 System Identification or Name System 4 02 System Location or Area Served LOWER OUTSIDE SUITE 03 System Installation Type New 04 Nominal Cooling Capacity (tons) of Condenser 2 05 Condenser Speed Type Multi -speed 06 Cooling System Zonal Control Type Not Zonal 07 Central Fan Integrated (CFI) Ventilation System Status Not a CFI system 08 System Bypass Duct Status No Bypass Duct 09 Date of System Airflow Rate Measurement 2019-04-08 10 Airflow Rate Protocol Utilized RA3.3 procedures for airflow rate measurement B. Hole for the placement of a Static Pressure Probe (HSPP), and Permanently Installed Static Pressure Probe (PSPP) in the Supply Plenum. Procedures for installing HSPP or PSPP are specified in RA3.3.1.1. 01 Method Used to Demonstrate Compliance with the HSPP/PSPP Requirement HSPP installed and labeled consistent with Figure RA3.3-1 C. Airflow Rate Measurement Apparatus and Procedure Information Instrument Specifications are given in RA3.3.1.1, and system airflow rate measurement apparatus information is given in RA3.3.2. 01 Airflow Rate Measurement Type used for this airflow rate verification. Traditional Flow Capture Hood according to procedure in RA3.3.3.1.4 02 Manufacturer of Airflow Measurement Apparatus ALNOR 03 Model number of Airflow Measurement Apparatus EBT731 04 Certification Status of the Airflow Measurement Apparatus Accuracy Certified by Manufacturer and listed on CEC Website at http://www.energy.ca.gov/title24/equipment_cert/ama_fas /index.html Registration Number: 219-P010089040A-000-001-M23005A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CalCERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2016.2.000 Report Generated: 2019-04-17 11:35:44 Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-23-H Space Conditioning System Airflow Rate (Page 2 of 3) MCH-23a Forced Air System Airflow Rate Measurement - Newly Installed Non -Zoned Systems or Zoned Multi -Speed Compressor D. Forced Air System Airflow Rate Measurement The procedures for System Airflow Rate Verification are specified in Reference Residential Appendix RA3.3. 01 Required Minimum System Airflow Rate (cfm/ton) 350 02 Required Minimum System Airflow Target (cfm) 700 03 Actual System Airflow Rate Measurement (cfm) 727 04 Compliance Statement: System airflow rate complies E. Additional Requirements 01 Air filters that meet the applicable requirements of Standards Section 150.0(m)12 or 150.0(m)13 were properly installed in the system during system air flow rate measurement identified on this Certificate of Installation. 02 The airflow rate measurement apparatus used to perform the airflow rate measurement identified on this Certificate of Installation was calibrated in accordance with the apparatus manufacturer's specifications and conforms to the instrumentation specifications given in RA3.3.1. 03 A visual inspection shall confirm that bypass ducts that deliver conditioned supply air directly to the space conditioning system return duct airflow are not used on newly constructed zonally controlled systems unless the Performance Certificate of Compliance indicates an allowance for use of a bypass duct. When a bypass duct is accounted for on the Performance Certificate of Compliance, the airflow rate shall conform to the specifications listed on the Certificate of Compliance. 04 All registers were fully open during the diagnostic test. 05 System fan was set at maximum speed during the diagnostic test. 06 If fresh air duct is part of the HVAC system it was not closed during the diagnostic test. 07 Airflow rate and fan watt draw shall be simultaneous measurements when used to calculate the Fan Efficacy tested value. 08 Multi -speed compressor space cooling systems or variable speed compressor systems shall verify air flow (cfm/ton) and fan efficacy (Watt/cfm) with system operating in cooling mode at the maximum compressor speed and the maximum air handler fan speed. The responsible person's signature on this compliance document affirms that all applicable requirements in this table have been met. Registration Number: 219-P010089040A-000-001-M23005A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2016.2.000 Report Generated: 2019-04-17 11:35:44 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-23-H Space Conditioning System Airflow Rate (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:19 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:19 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M23005A-0000 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2016.2.000 Report Generated: 2019-04-17 11:35:44 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-23-H Space Conditioning System Airflow Rate (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. Ducted Cooling System Information 01 System Identification or Name System 5 02 System Location or Area Served LOWER INNER SUITE 03 System Installation Type New 04 Nominal Cooling Capacity (tons) of Condenser 1.5 05 Condenser Speed Type Multi -speed 06 Cooling System Zonal Control Type Not Zonal 07 Central Fan Integrated (CFI) Ventilation System Status Not a CFI system 08 System Bypass Duct Status No Bypass Duct 09 Date of System Airflow Rate Measurement 2019-04-08 10 Airflow Rate Protocol Utilized RA3.3 procedures for airflow rate measurement B. Hole for the placement of a Static Pressure Probe (HSPP), and Permanently Installed Static Pressure Probe (PSPP) in the Supply Plenum. Procedures for installing HSPP or PSPP are specified in RA3.3.1.1. 01 Method Used to Demonstrate Compliance with the HSPP/PSPP Requirement HSPP installed and labeled consistent with Figure RA3.3-1 C. Airflow Rate Measurement Apparatus and Procedure Information Instrument Specifications are given in RA3.3.1.1, and system airflow rate measurement apparatus information is given in RA3.3.2. 01 Airflow Rate Measurement Type used for this airflow rate verification. Traditional Flow Capture Hood according to procedure in RA3.3.3.1.4 02 Manufacturer of Airflow Measurement Apparatus ALNOR 03 Model number of Airflow Measurement Apparatus EBT731 04 Certification Status of the Airflow Measurement Apparatus Accuracy Certified by Manufacturer and listed on CEC Website at http://www.energy.ca.gov/title24/equipment_cert/ama_fas /index.html Registration Number: 219-P010089040A-000-001-M23006A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CalCERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2016.2.000 Report Generated: 2019-04-17 11:38:00 Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-23-H Space Conditioning System Airflow Rate (Page 2 of 3) MCH-23a Forced Air System Airflow Rate Measurement - Newly Installed Non -Zoned Systems or Zoned Multi -Speed Compressor D. Forced Air System Airflow Rate Measurement The procedures for System Airflow Rate Verification are specified in Reference Residential Appendix RA3.3. 01 Required Minimum System Airflow Rate (cfm/ton) 350 02 Required Minimum System Airflow Target (cfm) 525 03 Actual System Airflow Rate Measurement (cfm) 548 04 Compliance Statement: System airflow rate complies E. Additional Requirements 01 Air filters that meet the applicable requirements of Standards Section 150.0(m)12 or 150.0(m)13 were properly installed in the system during system air flow rate measurement identified on this Certificate of Installation. 02 The airflow rate measurement apparatus used to perform the airflow rate measurement identified on this Certificate of Installation was calibrated in accordance with the apparatus manufacturer's specifications and conforms to the instrumentation specifications given in RA3.3.1. 03 A visual inspection shall confirm that bypass ducts that deliver conditioned supply air directly to the space conditioning system return duct airflow are not used on newly constructed zonally controlled systems unless the Performance Certificate of Compliance indicates an allowance for use of a bypass duct. When a bypass duct is accounted for on the Performance Certificate of Compliance, the airflow rate shall conform to the specifications listed on the Certificate of Compliance. 04 All registers were fully open during the diagnostic test. 05 System fan was set at maximum speed during the diagnostic test. 06 If fresh air duct is part of the HVAC system it was not closed during the diagnostic test. 07 Airflow rate and fan watt draw shall be simultaneous measurements when used to calculate the Fan Efficacy tested value. 08 Multi -speed compressor space cooling systems or variable speed compressor systems shall verify air flow (cfm/ton) and fan efficacy (Watt/cfm) with system operating in cooling mode at the maximum compressor speed and the maximum air handler fan speed. The responsible person's signature on this compliance document affirms that all applicable requirements in this table have been met. Registration Number: 219-P010089040A-000-001-M23006A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2016.2.000 Report Generated: 2019-04-17 11:38:00 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-23-H Space Conditioning System Airflow Rate (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:19 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:19 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M23006A-0000 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2016.2.000 Report Generated: 2019-04-17 11:38:00 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-23-H Space Conditioning System Airflow Rate (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. Ducted Cooling System Information 01 System Identification or Name System 6 02 System Location or Area Served UPPER POOL SUITE 03 System Installation Type New 04 Nominal Cooling Capacity (tons) of Condenser 2 05 Condenser Speed Type Multi -speed 06 Cooling System Zonal Control Type Not Zonal 07 Central Fan Integrated (CFI) Ventilation System Status Not a CFI system 08 System Bypass Duct Status No Bypass Duct 09 Date of System Airflow Rate Measurement 2019-04-08 10 Airflow Rate Protocol Utilized RA3.3 procedures for airflow rate measurement B. Hole for the placement of a Static Pressure Probe (HSPP), and Permanently Installed Static Pressure Probe (PSPP) in the Supply Plenum. Procedures for installing HSPP or PSPP are specified in RA3.3.1.1. 01 Method Used to Demonstrate Compliance with the HSPP/PSPP Requirement HSPP installed and labeled consistent with Figure RA3.3-1 C. Airflow Rate Measurement Apparatus and Procedure Information Instrument Specifications are given in RA3.3.1.1, and system airflow rate measurement apparatus information is given in RA3.3.2. 01 Airflow Rate Measurement Type used for this airflow rate verification. Traditional Flow Capture Hood according to procedure in RA3.3.3.1.4 02 Manufacturer of Airflow Measurement Apparatus ALNOR 03 Model number of Airflow Measurement Apparatus EBT731 04 Certification Status of the Airflow Measurement Apparatus Accuracy Certified by Manufacturer and listed on CEC Website at http://www.energy.ca.gov/title24/equipment_cert/ama_fas /index.html Registration Number: 219-P010089040A-000-001-M23007A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CalCERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2016.2.000 Report Generated: 2019-04-17 11:41:02 Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-23-H Space Conditioning System Airflow Rate (Page 2 of 3) MCH-23a Forced Air System Airflow Rate Measurement - Newly Installed Non -Zoned Systems or Zoned Multi -Speed Compressor D. Forced Air System Airflow Rate Measurement The procedures for System Airflow Rate Verification are specified in Reference Residential Appendix RA3.3. 01 Required Minimum System Airflow Rate (cfm/ton) 350 02 Required Minimum System Airflow Target (cfm) 700 03 Actual System Airflow Rate Measurement (cfm) 719 04 Compliance Statement: System airflow rate complies E. Additional Requirements 01 Air filters that meet the applicable requirements of Standards Section 150.0(m)12 or 150.0(m)13 were properly installed in the system during system air flow rate measurement identified on this Certificate of Installation. 02 The airflow rate measurement apparatus used to perform the airflow rate measurement identified on this Certificate of Installation was calibrated in accordance with the apparatus manufacturer's specifications and conforms to the instrumentation specifications given in RA3.3.1. 03 A visual inspection shall confirm that bypass ducts that deliver conditioned supply air directly to the space conditioning system return duct airflow are not used on newly constructed zonally controlled systems unless the Performance Certificate of Compliance indicates an allowance for use of a bypass duct. When a bypass duct is accounted for on the Performance Certificate of Compliance, the airflow rate shall conform to the specifications listed on the Certificate of Compliance. 04 All registers were fully open during the diagnostic test. 05 System fan was set at maximum speed during the diagnostic test. 06 If fresh air duct is part of the HVAC system it was not closed during the diagnostic test. 07 Airflow rate and fan watt draw shall be simultaneous measurements when used to calculate the Fan Efficacy tested value. 08 Multi -speed compressor space cooling systems or variable speed compressor systems shall verify air flow (cfm/ton) and fan efficacy (Watt/cfm) with system operating in cooling mode at the maximum compressor speed and the maximum air handler fan speed. The responsible person's signature on this compliance document affirms that all applicable requirements in this table have been met. Registration Number: 219-P010089040A-000-001-M23007A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CalCERTS CA Building Energy Efficiency Standards Report Version: 2016.2.000 Report Generated: 2019-04-17 11:41:02 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-23-H Space Conditioning System Airflow Rate (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:19 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:19 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M23007A-0000 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2016.2.000 Report Generated: 2019-04-17 11:41:02 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-23-H Space Conditioning System Airflow Rate (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. Ducted Cooling System Information 01 System Identification or Name System 7 02 System Location or Area Served UPPER ENTRY SUITE 03 System Installation Type New 04 Nominal Cooling Capacity (tons) of Condenser 2 05 Condenser Speed Type Multi -speed 06 Cooling System Zonal Control Type Not Zonal 07 Central Fan Integrated (CFI) Ventilation System Status Not a CFI system 08 System Bypass Duct Status No Bypass Duct 09 Date of System Airflow Rate Measurement 2019-04-08 10 Airflow Rate Protocol Utilized RA3.3 procedures for airflow rate measurement B. Hole for the placement of a Static Pressure Probe (HSPP), and Permanently Installed Static Pressure Probe (PSPP) in the Supply Plenum. Procedures for installing HSPP or PSPP are specified in RA3.3.1.1. 01 Method Used to Demonstrate Compliance with the HSPP/PSPP Requirement HSPP installed and labeled consistent with Figure RA3.3-1 C. Airflow Rate Measurement Apparatus and Procedure Information Instrument Specifications are given in RA3.3.1.1, and system airflow rate measurement apparatus information is given in RA3.3.2. 01 Airflow Rate Measurement Type used for this airflow rate verification. Traditional Flow Capture Hood according to procedure in RA3.3.3.1.4 02 Manufacturer of Airflow Measurement Apparatus ALNOR 03 Model number of Airflow Measurement Apparatus EBT731 04 Certification Status of the Airflow Measurement Apparatus Accuracy Certified by Manufacturer and listed on CEC Website at http://www.energy.ca.gov/title24/equipment_cert/ama_fas /index.html Registration Number: 219-P010089040A-000-001-M23008A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CalCERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2016.2.000 Report Generated: 2019-04-17 11:51:28 Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-23-H Space Conditioning System Airflow Rate (Page 2 of 3) MCH-23a Forced Air System Airflow Rate Measurement - Newly Installed Non -Zoned Systems or Zoned Multi -Speed Compressor D. Forced Air System Airflow Rate Measurement The procedures for System Airflow Rate Verification are specified in Reference Residential Appendix RA3.3. 01 Required Minimum System Airflow Rate (cfm/ton) 350 02 Required Minimum System Airflow Target (cfm) 700 03 Actual System Airflow Rate Measurement (cfm) 742 04 Compliance Statement: System airflow rate complies E. Additional Requirements 01 Air filters that meet the applicable requirements of Standards Section 150.0(m)12 or 150.0(m)13 were properly installed in the system during system air flow rate measurement identified on this Certificate of Installation. 02 The airflow rate measurement apparatus used to perform the airflow rate measurement identified on this Certificate of Installation was calibrated in accordance with the apparatus manufacturer's specifications and conforms to the instrumentation specifications given in RA3.3.1. 03 A visual inspection shall confirm that bypass ducts that deliver conditioned supply air directly to the space conditioning system return duct airflow are not used on newly constructed zonally controlled systems unless the Performance Certificate of Compliance indicates an allowance for use of a bypass duct. When a bypass duct is accounted for on the Performance Certificate of Compliance, the airflow rate shall conform to the specifications listed on the Certificate of Compliance. 04 All registers were fully open during the diagnostic test. 05 System fan was set at maximum speed during the diagnostic test. 06 If fresh air duct is part of the HVAC system it was not closed during the diagnostic test. 07 Airflow rate and fan watt draw shall be simultaneous measurements when used to calculate the Fan Efficacy tested value. 08 Multi -speed compressor space cooling systems or variable speed compressor systems shall verify air flow (cfm/ton) and fan efficacy (Watt/cfm) with system operating in cooling mode at the maximum compressor speed and the maximum air handler fan speed. The responsible person's signature on this compliance document affirms that all applicable requirements in this table have been met. Registration Number: 219-P010089040A-000-001-M23008A-0000 Registration Date/Time: 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2016.2.000 Report Generated: 2019-04-17 11:51:28 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-23-H Space Conditioning System Airflow Rate (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:19 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:19 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M23008A-0000 2019-04-17 12:19:19 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2016.2.000 Report Generated: 2019-04-17 11:51:28 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-22-H Space Conditioning System Fan Efficacy (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. Ducted Cooling System Information 01 System Identification or Name System 1 02 System Location or Area Served GREATROOM/KITCHEN 03 System Installation Type New 04 Nominal Cooling Capacity (tons) of Condenser 5 05 Condenser Speed Type Multi -speed 06 Cooling System Zonal Control Type Not Zonal 07 Central Fan Integrated (CFI) Ventilation System Status Not a CFI system 08 System Bypass Duct Status No Bypass Duct 09 Date of System Airflow Rate Measurement 2019-04-08 10 Airflow Rate Protocol utilized RA3.3 procedures for airflow rate measurement B. Fan Watt Measurement Apparatus and Procedure Information Instrument Specifications are given in RA3.3.1, and system fan watt measurement apparatus information is given in RA3.3.2.2. 01 Fan Watt Verification Device Used. Portable watt meter MCH-22a Forced Air System Fan Efficacy Measurement - Newly Installed Non -Zoned Systems or Zoned Multi -Speed Compressor C. Forced Air System Fan Efficacy Measurement The procedures for System Fan Watt Verification are specified in Reference Residential Appendix RA3.3 01 Actual Tested Watts 921 02 Actual Tested Airflow from MCH-23 (cfm) 1773 03 Required Fan Efficacy (watts/cfm) 0.58 04 Actual Fan Efficacy (watts/cfm) 0.52 05 Compliance Statement: System fan efficacy complies Registration Number: 219-P010089040A-000-001-M22002A-0000 Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CalCERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:27:25 CERTIFICATE OF INSTALLATION CF2R-MCH-22-H Space Conditioning System Fan Efficacy (Page 2 of 3) D. Additional Requirements 01 All registers were fully open during the diagnostic test. 02 System fan was set at maximum speed during the diagnostic test. 03 If fresh air duct is part of the HVAC system it was not closed during the diagnostic test. 04 Airflow rate and fan watt draw shall be simultaneous measurements when used to calculate the Fan Efficacy tested value. 05 Multi -speed compressor space cooling systems or variable speed compressor systems shall verify air flow (cfm/ton) and fan efficacy (Watt/cfm) with system operating in cooling mode at the maximum compressor speed and the maximum air handler fan speed. 06 Zoned cooling air distribution systems with single speed compressors shall meet both the airflow (cfm/ton) and fan efficacy (Watt/cfm) criteria in every zonal control mode. The responsible person's signature on this compliance document affirms that all applicable requirements in this table have been met. Registration Number: 219-P010089040A-000-001-M22002A-0000 CaICERTS, Inc HERS PROVIDER • Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:27:25 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-22-H Space Conditioning System Fan Efficacy (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:20 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:20 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M22002A-0000 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:27:25 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-22-H Space Conditioning System Fan Efficacy (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. Ducted Cooling System Information 01 System Identification or Name System 2 02 System Location or Area Served KITCHEN 03 System Installation Type New 04 Nominal Cooling Capacity (tons) of Condenser 3 05 Condenser Speed Type Multi -speed 06 Cooling System Zonal Control Type Not Zonal 07 Central Fan Integrated (CFI) Ventilation System Status Not a CFI system 08 System Bypass Duct Status No Bypass Duct 09 Date of System Airflow Rate Measurement 2019-04-08 10 Airflow Rate Protocol utilized RA3.3 procedures for airflow rate measurement B. Fan Watt Measurement Apparatus and Procedure Information Instrument Specifications are given in RA3.3.1, and system fan watt measurement apparatus information is given in RA3.3.2.2. 01 Fan Watt Verification Device Used. Portable watt meter MCH-22a Forced Air System Fan Efficacy Measurement - Newly Installed Non -Zoned Systems or Zoned Multi -Speed Compressor C. Forced Air System Fan Efficacy Measurement The procedures for System Fan Watt Verification are specified in Reference Residential Appendix RA3.3 01 Actual Tested Watts 563 02 Actual Tested Airflow from MCH-23 (cfm) 1104 03 Required Fan Efficacy (watts/cfm) 0.58 04 Actual Fan Efficacy (watts/cfm) 0.51 05 Compliance Statement: System fan efficacy complies Registration Number: 219-P010089040A-000-001-M22003A-0000 Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CalCERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:31:41 CERTIFICATE OF INSTALLATION CF2R-MCH-22-H Space Conditioning System Fan Efficacy (Page 2 of 3) D. Additional Requirements 01 All registers were fully open during the diagnostic test. 02 System fan was set at maximum speed during the diagnostic test. 03 If fresh air duct is part of the HVAC system it was not closed during the diagnostic test. 04 Airflow rate and fan watt draw shall be simultaneous measurements when used to calculate the Fan Efficacy tested value. 05 Multi -speed compressor space cooling systems or variable speed compressor systems shall verify air flow (cfm/ton) and fan efficacy (Watt/cfm) with system operating in cooling mode at the maximum compressor speed and the maximum air handler fan speed. 06 Zoned cooling air distribution systems with single speed compressors shall meet both the airflow (cfm/ton) and fan efficacy (Watt/cfm) criteria in every zonal control mode. The responsible person's signature on this compliance document affirms that all applicable requirements in this table have been met. Registration Number: 219-P010089040A-000-001-M22003A-0000 CaICERTS, Inc HERS PROVIDER • Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:31:41 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-22-H Space Conditioning System Fan Efficacy (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:20 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:20 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M22003A-0000 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:31:41 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-22-H Space Conditioning System Fan Efficacy (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. Ducted Cooling System Information 01 System Identification or Name System 3 02 System Location or Area Served MASTER 03 System Installation Type New 04 Nominal Cooling Capacity (tons) of Condenser 5 05 Condenser Speed Type Multi -speed 06 Cooling System Zonal Control Type Not Zonal 07 Central Fan Integrated (CFI) Ventilation System Status Not a CFI system 08 System Bypass Duct Status No Bypass Duct 09 Date of System Airflow Rate Measurement 2019-04-08 10 Airflow Rate Protocol utilized RA3.3 procedures for airflow rate measurement B. Fan Watt Measurement Apparatus and Procedure Information Instrument Specifications are given in RA3.3.1, and system fan watt measurement apparatus information is given in RA3.3.2.2. 01 Fan Watt Verification Device Used. Portable watt meter MCH-22a Forced Air System Fan Efficacy Measurement - Newly Installed Non -Zoned Systems or Zoned Multi -Speed Compressor C. Forced Air System Fan Efficacy Measurement The procedures for System Fan Watt Verification are specified in Reference Residential Appendix RA3.3 01 Actual Tested Watts 931 02 Actual Tested Airflow from MCH-23 (cfm) 1791 03 Required Fan Efficacy (watts/cfm) 0.58 04 Actual Fan Efficacy (watts/cfm) 0.52 05 Compliance Statement: System fan efficacy complies Registration Number: 219-P010089040A-000-001-M22004A-0000 Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CalCERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:33:32 CERTIFICATE OF INSTALLATION CF2R-MCH-22-H Space Conditioning System Fan Efficacy (Page 2 of 3) D. Additional Requirements 01 All registers were fully open during the diagnostic test. 02 System fan was set at maximum speed during the diagnostic test. 03 If fresh air duct is part of the HVAC system it was not closed during the diagnostic test. 04 Airflow rate and fan watt draw shall be simultaneous measurements when used to calculate the Fan Efficacy tested value. 05 Multi -speed compressor space cooling systems or variable speed compressor systems shall verify air flow (cfm/ton) and fan efficacy (Watt/cfm) with system operating in cooling mode at the maximum compressor speed and the maximum air handler fan speed. 06 Zoned cooling air distribution systems with single speed compressors shall meet both the airflow (cfm/ton) and fan efficacy (Watt/cfm) criteria in every zonal control mode. The responsible person's signature on this compliance document affirms that all applicable requirements in this table have been met. Registration Number: 219-P010089040A-000-001-M22004A-0000 CaICERTS, Inc HERS PROVIDER • Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:33:32 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-22-H Space Conditioning System Fan Efficacy (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:20 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:20 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M22004A-0000 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:33:32 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-22-H Space Conditioning System Fan Efficacy (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. Ducted Cooling System Information 01 System Identification or Name System 4 02 System Location or Area Served LOWER OUTSIDE SUITE 03 System Installation Type New 04 Nominal Cooling Capacity (tons) of Condenser 2 05 Condenser Speed Type Multi -speed 06 Cooling System Zonal Control Type Not Zonal 07 Central Fan Integrated (CFI) Ventilation System Status Not a CFI system 08 System Bypass Duct Status No Bypass Duct 09 Date of System Airflow Rate Measurement 2019-04-08 10 Airflow Rate Protocol utilized RA3.3 procedures for airflow rate measurement B. Fan Watt Measurement Apparatus and Procedure Information Instrument Specifications are given in RA3.3.1, and system fan watt measurement apparatus information is given in RA3.3.2.2. 01 Fan Watt Verification Device Used. Portable watt meter MCH-22a Forced Air System Fan Efficacy Measurement - Newly Installed Non -Zoned Systems or Zoned Multi -Speed Compressor C. Forced Air System Fan Efficacy Measurement The procedures for System Fan Watt Verification are specified in Reference Residential Appendix RA3.3 01 Actual Tested Watts 363 02 Actual Tested Airflow from MCH-23 (cfm) 727 03 Required Fan Efficacy (watts/cfm) 0.58 04 Actual Fan Efficacy (watts/cfm) 0.5 05 Compliance Statement: System fan efficacy complies Registration Number: 219-P010089040A-000-001-M22005A-0000 Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CalCERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:36:11 CERTIFICATE OF INSTALLATION CF2R-MCH-22-H Space Conditioning System Fan Efficacy (Page 2 of 3) D. Additional Requirements 01 All registers were fully open during the diagnostic test. 02 System fan was set at maximum speed during the diagnostic test. 03 If fresh air duct is part of the HVAC system it was not closed during the diagnostic test. 04 Airflow rate and fan watt draw shall be simultaneous measurements when used to calculate the Fan Efficacy tested value. 05 Multi -speed compressor space cooling systems or variable speed compressor systems shall verify air flow (cfm/ton) and fan efficacy (Watt/cfm) with system operating in cooling mode at the maximum compressor speed and the maximum air handler fan speed. 06 Zoned cooling air distribution systems with single speed compressors shall meet both the airflow (cfm/ton) and fan efficacy (Watt/cfm) criteria in every zonal control mode. The responsible person's signature on this compliance document affirms that all applicable requirements in this table have been met. Registration Number: 219-P010089040A-000-001-M22005A-0000 CaICERTS, Inc HERS PROVIDER • Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:36:11 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-22-H Space Conditioning System Fan Efficacy (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:20 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:20 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M22005A-0000 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:36:11 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-22-H Space Conditioning System Fan Efficacy (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. Ducted Cooling System Information 01 System Identification or Name System 5 02 System Location or Area Served LOWER INNER SUITE 03 System Installation Type New 04 Nominal Cooling Capacity (tons) of Condenser 1.5 05 Condenser Speed Type Multi -speed 06 Cooling System Zonal Control Type Not Zonal 07 Central Fan Integrated (CFI) Ventilation System Status Not a CFI system 08 System Bypass Duct Status No Bypass Duct 09 Date of System Airflow Rate Measurement 2019-04-08 10 Airflow Rate Protocol utilized RA3.3 procedures for airflow rate measurement B. Fan Watt Measurement Apparatus and Procedure Information Instrument Specifications are given in RA3.3.1, and system fan watt measurement apparatus information is given in RA3.3.2.2. 01 Fan Watt Verification Device Used. Portable watt meter MCH-22a Forced Air System Fan Efficacy Measurement - Newly Installed Non -Zoned Systems or Zoned Multi -Speed Compressor C. Forced Air System Fan Efficacy Measurement The procedures for System Fan Watt Verification are specified in Reference Residential Appendix RA3.3 01 Actual Tested Watts 284 02 Actual Tested Airflow from MCH-23 (cfm) 548 03 Required Fan Efficacy (watts/cfm) 0.58 04 Actual Fan Efficacy (watts/cfm) 0.52 05 Compliance Statement: System fan efficacy complies Registration Number: 219-P010089040A-000-001-M22006A-0000 Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CalCERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:38:46 CERTIFICATE OF INSTALLATION CF2R-MCH-22-H Space Conditioning System Fan Efficacy (Page 2 of 3) D. Additional Requirements 01 All registers were fully open during the diagnostic test. 02 System fan was set at maximum speed during the diagnostic test. 03 If fresh air duct is part of the HVAC system it was not closed during the diagnostic test. 04 Airflow rate and fan watt draw shall be simultaneous measurements when used to calculate the Fan Efficacy tested value. 05 Multi -speed compressor space cooling systems or variable speed compressor systems shall verify air flow (cfm/ton) and fan efficacy (Watt/cfm) with system operating in cooling mode at the maximum compressor speed and the maximum air handler fan speed. 06 Zoned cooling air distribution systems with single speed compressors shall meet both the airflow (cfm/ton) and fan efficacy (Watt/cfm) criteria in every zonal control mode. The responsible person's signature on this compliance document affirms that all applicable requirements in this table have been met. Registration Number: 219-P010089040A-000-001-M22006A-0000 CaICERTS, Inc HERS PROVIDER • Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:38:46 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-22-H Space Conditioning System Fan Efficacy (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:20 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:20 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M22006A-0000 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:38:46 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-22-H Space Conditioning System Fan Efficacy (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. Ducted Cooling System Information 01 System Identification or Name System 6 02 System Location or Area Served UPPER POOL SUITE 03 System Installation Type New 04 Nominal Cooling Capacity (tons) of Condenser 2 05 Condenser Speed Type Multi -speed 06 Cooling System Zonal Control Type Not Zonal 07 Central Fan Integrated (CFI) Ventilation System Status Not a CFI system 08 System Bypass Duct Status No Bypass Duct 09 Date of System Airflow Rate Measurement 2019-04-08 10 Airflow Rate Protocol utilized RA3.3 procedures for airflow rate measurement B. Fan Watt Measurement Apparatus and Procedure Information Instrument Specifications are given in RA3.3.1, and system fan watt measurement apparatus information is given in RA3.3.2.2. 01 Fan Watt Verification Device Used. Portable watt meter MCH-22a Forced Air System Fan Efficacy Measurement - Newly Installed Non -Zoned Systems or Zoned Multi -Speed Compressor C. Forced Air System Fan Efficacy Measurement The procedures for System Fan Watt Verification are specified in Reference Residential Appendix RA3.3 01 Actual Tested Watts 366 02 Actual Tested Airflow from MCH-23 (cfm) 719 03 Required Fan Efficacy (watts/cfm) 0.58 04 Actual Fan Efficacy (watts/cfm) 0.51 05 Compliance Statement: System fan efficacy complies Registration Number: 219-P010089040A-000-001-M22007A-0000 Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CalCERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:41:34 CERTIFICATE OF INSTALLATION CF2R-MCH-22-H Space Conditioning System Fan Efficacy (Page 2 of 3) D. Additional Requirements 01 All registers were fully open during the diagnostic test. 02 System fan was set at maximum speed during the diagnostic test. 03 If fresh air duct is part of the HVAC system it was not closed during the diagnostic test. 04 Airflow rate and fan watt draw shall be simultaneous measurements when used to calculate the Fan Efficacy tested value. 05 Multi -speed compressor space cooling systems or variable speed compressor systems shall verify air flow (cfm/ton) and fan efficacy (Watt/cfm) with system operating in cooling mode at the maximum compressor speed and the maximum air handler fan speed. 06 Zoned cooling air distribution systems with single speed compressors shall meet both the airflow (cfm/ton) and fan efficacy (Watt/cfm) criteria in every zonal control mode. The responsible person's signature on this compliance document affirms that all applicable requirements in this table have been met. Registration Number: 219-P010089040A-000-001-M22007A-0000 CaICERTS, Inc HERS PROVIDER • Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:41:34 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-22-H Space Conditioning System Fan Efficacy (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:20 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:20 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M22007A-0000 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:41:34 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-22-H Space Conditioning System Fan Efficacy (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. Ducted Cooling System Information 01 System Identification or Name System 7 02 System Location or Area Served UPPER ENTRY SUITE 03 System Installation Type New 04 Nominal Cooling Capacity (tons) of Condenser 2 05 Condenser Speed Type Multi -speed 06 Cooling System Zonal Control Type Not Zonal 07 Central Fan Integrated (CFI) Ventilation System Status Not a CFI system 08 System Bypass Duct Status No Bypass Duct 09 Date of System Airflow Rate Measurement 2019-04-08 10 Airflow Rate Protocol utilized RA3.3 procedures for airflow rate measurement B. Fan Watt Measurement Apparatus and Procedure Information Instrument Specifications are given in RA3.3.1, and system fan watt measurement apparatus information is given in RA3.3.2.2. 01 Fan Watt Verification Device Used. Portable watt meter MCH-22a Forced Air System Fan Efficacy Measurement - Newly Installed Non -Zoned Systems or Zoned Multi -Speed Compressor C. Forced Air System Fan Efficacy Measurement The procedures for System Fan Watt Verification are specified in Reference Residential Appendix RA3.3 01 Actual Tested Watts 393 02 Actual Tested Airflow from MCH-23 (cfm) 742 03 Required Fan Efficacy (watts/cfm) 0.58 04 Actual Fan Efficacy (watts/cfm) 0.53 05 Compliance Statement: System fan efficacy complies Registration Number: 219-P010089040A-000-001-M22008A-0000 Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CalCERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:51:53 CERTIFICATE OF INSTALLATION CF2R-MCH-22-H Space Conditioning System Fan Efficacy (Page 2 of 3) D. Additional Requirements 01 All registers were fully open during the diagnostic test. 02 System fan was set at maximum speed during the diagnostic test. 03 If fresh air duct is part of the HVAC system it was not closed during the diagnostic test. 04 Airflow rate and fan watt draw shall be simultaneous measurements when used to calculate the Fan Efficacy tested value. 05 Multi -speed compressor space cooling systems or variable speed compressor systems shall verify air flow (cfm/ton) and fan efficacy (Watt/cfm) with system operating in cooling mode at the maximum compressor speed and the maximum air handler fan speed. 06 Zoned cooling air distribution systems with single speed compressors shall meet both the airflow (cfm/ton) and fan efficacy (Watt/cfm) criteria in every zonal control mode. The responsible person's signature on this compliance document affirms that all applicable requirements in this table have been met. Registration Number: 219-P010089040A-000-001-M22008A-0000 CaICERTS, Inc HERS PROVIDER • Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:51:53 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-22-H Space Conditioning System Fan Efficacy (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:20 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:20 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M22008A-0000 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:51:53 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-25-H Refrigerant Charge Verification (Page 1 of 4) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. System Information Each system requiring refrigerant charge verification will be documented on a separate certificate. 01 System Identification or Name System 6 02 System Location or Area Served UPPER POOL SUITE 03 Condenser (or package unit) Make or Brand DAIKIN 04 Condenser (or package unit) Model Number RX24RMVJU 05 Nominal Cooling Capacity (tons) of Condenser 2 06 Condenser (or package unit) Serial Number E000332 07 Refrigerant Type R-410A 08 Other Refrigerant Type (if applicable) N/A 09 Liquid Line Filter Drier Installed According to Manufacturers Specifications (if applicable) Yes 10 System Installation Type New 11 Fault Indicator Display (FID) Status (Note: Even systems with a FID must have refrigerant charge verified by installer). This system does not have a FID device installed 12 Is the system of a type that the minimum airflow can be verified using an approved measurement procedure (RA3.3 or RA3.3.3)? Yes, this is a ducted system and one of the system airflow rate measurement procedures in RA3.3 or RA3.3.3 can be used to verify system airflow rate requirements. 13 Is the system of a type that approved refrigerant charge verification procedures can be used to verify compliance with the refrigerant charge verification requirements when temperatures are >= 55°F (RA3.2.2, or RA1)? No, none of the refrigerant charge verification procedures in RA3.2.2, or RA1 are applicable to the system therefore compliance shall use HERS Rater observation of the installer's weigh-in charging procedure 14 Date of Refrigerant Charge Verification for this system 2019-04-08 15 Refrigerant charge verification method used. Weigh-in with HERS Rater Observation 16 Person who performed the Refrigerant Charge Verification reported on this Certificate of Installation HVAC system installer 17 HERS Verification Compliance Requirement Status System does not qualify for group sampling Registration Number: 219-P010089040A-000-001-M25007A-0000 Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Report Generated: 2019-04-17 11:49:22 Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-25-H Refrigerant Charge Verification (Page 2 of 4) MCH-25c - Refrigerant Charge Verification - Weigh In Observation Procedure B. Instrument Calibration Procedures for instrument calibration are given in Reference Residential Appendix RA3.2.2 and RA3.2.3.1.4 01 Date of expiration of Digital Refrigerant Scale Calibration 2019-05-31 02 Date of Digital Thermometer and Temperature Sensor Calibration 2019-05-31 03 Digital Refrigerant Scale Calibration Status Calibration is current 04 Digital Thermocouple Calibration Status Calibration is current C. Measurement Access Hole (MAH) Verification Procedures for installing MAH are specified in Reference Residential Appendix RA3.2.2.3 01 Method Used to Demonstrate Compliance with the Measurement Access Hole (MAH) Requirement MAH installed and labeled consistent with Figure 3.2-1 D. Minimum System Airflow Rate Verification Procedures for verifying minimum system airflow are specified in Reference Residential Appendix RA3.3.3. 01 Minimum Required System Airflow Rate (cfm) 700 02 System Airflow Rate Verification Status System complies with minimum airflow rate requirements E. Weigh In Charge Procedure Procedures for Refrigerant Charge using the Weigh-in Charging Procedure are given in Reference Residential Appendix RA3.2.2.2 and RA3.2.3 01 Measured Condenser Air Entering Dry-bulb Temperature (Tcondenser, db) ((° F) 72 02 Specify the Method of Weigh-in TotalCharge 03 Manufacturer Standard Charge for Condenser (lbs, oz.) 3, 3 04 Manufacturer Standard Liquid Line Length (ft) 98 05 Manufacturer's Standard Liquid Line Diameter (in) 0.25 06 Manufacturer's Standard Indoor Coil Size (tons) 2 07 Installed Liquid Line Length (ft) 26 08 Installed Liquid Line Diameter (in) 0.25 Registration Number: 219-P010089040A-000-001-M25007A-0000 Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:49:22 CERTIFICATE OF INSTALLATION CF2R-MCH-25-H Refrigerant Charge Verification (Page 3 of 4) E. Weigh In Charge Procedure Procedures for Refrigerant Charge using the Weigh-in Charging Procedure are given in Reference Residential Appendix RA3.2.2.2 and RA3.2.3 09 Installed Indoor Coil Size (tons) 2 10 Charge Adjustment to Standard Charge from Manufacturer's Specifications (ounces, positive = add, negative = remove) 0 11 Refrigerant Required to be Weighed in by the Installer (lbs, oz) 3, 3 12 Refrigerant Weighed in by Installer (Ibs, oz) 3, 3 13 Compliance Statement: System complies with the Weigh-in charge requirement F. Weigh In Charge Procedure - Additional Requirements 01 All brazing of refrigerant lines done with dry nitrogen in lines and evaporator coil 02 The indoor coil correction to refrigerant weight is used if it is supplied by the manufacturer. 03 Prior to introducing refrigerant, system is evacuated to 500 microns or less and, when isolated, has risen no more than 300 microns after 5 minutes. 04 When applicable and if necessary to avoid delay of approval of dwelling units completed when outside temperatures are below 55°F, the enforcement agency may approve compliance with the refrigerant charge verification requirements based on registration of this CF2R-MCH-25, documenting use of the RA3.2.3.1 HVAC Installer Weigh -In Charging Procedure when the optional Section RA3.2.3.2 HERS Rater Observation of Weigh -In Charging Procedure is not used. As condition for such enforcement agency approval, the responsible person's signature on this compliance document affirms the installer agrees to return to correct refrigerant charge if a HERS Rater determines at a later time, when the outside temperature is 55°F or greater, that refrigerant charge correction is necessary. The responsible person's signature on this compliance document affirms that all applicable requirements in this table have been met. MCH-25d - Refrigeration Charge Verification - Fault Indicator Display (FID) G. Fault Indicator Display This section does not apply to this project. H. Fault Indicator Display - Additional Requirements This section does not apply to this project. Registration Number: 219-P010089040A-000-001-M25007A-0000 Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Report Generated: 2019-04-17 11:49:22 Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-25-H Refrigerant Charge Verification (Page 4 of 4) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:20 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:20 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M25007A-0000 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:49:22 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-25-H Refrigerant Charge Verification (Page 1 of 4) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. System Information Each system requiring refrigerant charge verification will be documented on a separate certificate. 01 System Identification or Name System 7 02 System Location or Area Served UPPER ENTRY SUITE 03 Condenser (or package unit) Make or Brand DAIKIN 04 Condenser (or package unit) Model Number RX24RMVJU 05 Nominal Cooling Capacity (tons) of Condenser 2 06 Condenser (or package unit) Serial Number E000333 07 Refrigerant Type R-410A 08 Other Refrigerant Type (if applicable) N/A 09 Liquid Line Filter Drier Installed According to Manufacturers Specifications (if applicable) Yes 10 System Installation Type New 11 Fault Indicator Display (FID) Status (Note: Even systems with a FID must have refrigerant charge verified by installer). This system does not have a FID device installed 12 Is the system of a type that the minimum airflow can be verified using an approved measurement procedure (RA3.3 or RA3.3.3)? Yes, this is a ducted system and one of the system airflow rate measurement procedures in RA3.3 or RA3.3.3 can be used to verify system airflow rate requirements. 13 Is the system of a type that approved refrigerant charge verification procedures can be used to verify compliance with the refrigerant charge verification requirements when temperatures are >= 55°F (RA3.2.2, or RA1)? No, none of the refrigerant charge verification procedures in RA3.2.2, or RA1 are applicable to the system therefore compliance shall use HERS Rater observation of the installer's weigh-in charging procedure 14 Date of Refrigerant Charge Verification for this system 2019-04-08 15 Refrigerant charge verification method used. Weigh-in with HERS Rater Observation 16 Person who performed the Refrigerant Charge Verification reported on this Certificate of Installation HVAC system installer 17 HERS Verification Compliance Requirement Status System does not qualify for group sampling Registration Number: 219-P010089040A-000-001-M25008A-0000 Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Report Generated: 2019-04-17 11:52:50 Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-25-H Refrigerant Charge Verification (Page 2 of 4) MCH-25c - Refrigerant Charge Verification - Weigh In Observation Procedure B. Instrument Calibration Procedures for instrument calibration are given in Reference Residential Appendix RA3.2.2 and RA3.2.3.1.4 01 Date of expiration of Digital Refrigerant Scale Calibration 2019-05-31 02 Date of Digital Thermometer and Temperature Sensor Calibration 2019-05-31 03 Digital Refrigerant Scale Calibration Status Calibration is current 04 Digital Thermocouple Calibration Status Calibration is current C. Measurement Access Hole (MAH) Verification Procedures for installing MAH are specified in Reference Residential Appendix RA3.2.2.3 01 Method Used to Demonstrate Compliance with the Measurement Access Hole (MAH) Requirement MAH installed and labeled consistent with Figure 3.2-1 D. Minimum System Airflow Rate Verification Procedures for verifying minimum system airflow are specified in Reference Residential Appendix RA3.3.3. 01 Minimum Required System Airflow Rate (cfm) 700 02 System Airflow Rate Verification Status System complies with minimum airflow rate requirements E. Weigh In Charge Procedure Procedures for Refrigerant Charge using the Weigh-in Charging Procedure are given in Reference Residential Appendix RA3.2.2.2 and RA3.2.3 01 Measured Condenser Air Entering Dry-bulb Temperature (Tcondenser, db) ((° F) 72 02 Specify the Method of Weigh-in TotalCharge 03 Manufacturer Standard Charge for Condenser (lbs, oz.) 3, 3 04 Manufacturer Standard Liquid Line Length (ft) 98 05 Manufacturer's Standard Liquid Line Diameter (in) 0.25 06 Manufacturer's Standard Indoor Coil Size (tons) 2 07 Installed Liquid Line Length (ft) 30 08 Installed Liquid Line Diameter (in) 0.25 Registration Number: 219-P010089040A-000-001-M25008A-0000 Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:52:50 CERTIFICATE OF INSTALLATION CF2R-MCH-25-H Refrigerant Charge Verification (Page 3 of 4) E. Weigh In Charge Procedure Procedures for Refrigerant Charge using the Weigh-in Charging Procedure are given in Reference Residential Appendix RA3.2.2.2 and RA3.2.3 09 Installed Indoor Coil Size (tons) 2 10 Charge Adjustment to Standard Charge from Manufacturer's Specifications (ounces, positive = add, negative = remove) 0 11 Refrigerant Required to be Weighed in by the Installer (lbs, oz) 3, 3 12 Refrigerant Weighed in by Installer (Ibs, oz) 3, 3 13 Compliance Statement: System complies with the Weigh-in charge requirement F. Weigh In Charge Procedure - Additional Requirements 01 All brazing of refrigerant lines done with dry nitrogen in lines and evaporator coil 02 The indoor coil correction to refrigerant weight is used if it is supplied by the manufacturer. 03 Prior to introducing refrigerant, system is evacuated to 500 microns or less and, when isolated, has risen no more than 300 microns after 5 minutes. 04 When applicable and if necessary to avoid delay of approval of dwelling units completed when outside temperatures are below 55°F, the enforcement agency may approve compliance with the refrigerant charge verification requirements based on registration of this CF2R-MCH-25, documenting use of the RA3.2.3.1 HVAC Installer Weigh -In Charging Procedure when the optional Section RA3.2.3.2 HERS Rater Observation of Weigh -In Charging Procedure is not used. As condition for such enforcement agency approval, the responsible person's signature on this compliance document affirms the installer agrees to return to correct refrigerant charge if a HERS Rater determines at a later time, when the outside temperature is 55°F or greater, that refrigerant charge correction is necessary. The responsible person's signature on this compliance document affirms that all applicable requirements in this table have been met. MCH-25d - Refrigeration Charge Verification - Fault Indicator Display (FID) G. Fault Indicator Display This section does not apply to this project. H. Fault Indicator Display - Additional Requirements This section does not apply to this project. Registration Number: 219-P010089040A-000-001-M25008A-0000 Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Report Generated: 2019-04-17 11:52:50 Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-25-H Refrigerant Charge Verification (Page 4 of 4) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:20 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:20 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M25008A-0000 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:52:50 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-26-H Rated Space Conditioning System Equipment Verification (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. System Information Procedures for verification of High SEER and EER Equipment are described in Reference Appendix RA3.4. Each HVAC system requ'ring verification must use a separate form. 01 System Name or Identification/Tag System 1 02 System Location or Area Served GREATROOM/KITCHEN 03 Status: SEER and EER performance compliance credit check Both SEER and EER HERS Verification is required 04 Directory used to certify product performance AHRI 05 AHRI certification number for the installed space conditioning system from http://www.ahridirectory.org 8256560 06 Does the directory used to certify product performance require a specific air handler/furnace make and model? i Yes R 5, I 07 Does the directory used to certify product performance require a time delay relay (+TDR)? Now t nc 08 Does the directory used to certify product performance require a TXV (+TXV)? No B. Rated Space Conditioning System Equipment Verification The data on nameplate of the installed component shall conform to the data for the component as shown in the Directory used to certify product performance in order to demonstrate compliance. Data from Nameplate of Installed system component Data from the Directory used to certify product performance for the rated system component Outdoor Condenser or Package Unit - Installed Manufacturer Name 01 GOODMAN 02 GOODMAN Outdoor Condenser or Package Unit - Installed Model Number 03 AVXC200601AE 04 AVXC200601AE Inside Coil - Installed Manufacturer Name 05 ASPEN 06 ASPEN Inside Coil - Installed Model Number 07 CC60G44245L004 08 CC60G44245L004 Air Handler/Furnace - Installed Manufacturer Name 09 GOODMAN 10 GOODMAN Registration Number: 219-P010089040A-000-001-M26002A-0000 Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CalCERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:28:10 CERTIFICATE OF INSTALLATION CF2R-MCH-26-H Rated Space Conditioning System Equipment Verification (Page 2 of 3) B. Rated Space Conditioning System Equipment Verification The data on nameplate of the installed component shall conform to the data for the component as shown in the Directory used to certify product performance in order to demonstrate compliance. Air Handler/Furnace - Installed Model Number 11 A M VC80805 CXCA 12 AMVC80805CXCA C. Verified Cooling System SEER 01 Required minimum SEER 18 02 Installed SEER 18.85 03 Compliance Statement: System passes SEER verification Signature by responsible party below certifies that the installed cooling equipment meets or exceeds the required value listed on the CF1R. D. Verified Cooling System EER 01 Required minimum EER N. 13 02 Installed EER — 13 03 Compliance Statement: System passes EER verification Signature by responsible party below certifies that the installed cooling equipment meets or exceeds the required value listed on the CF1R. E. Verified Cooling System Air Handler/Furnace 01 If a specific air handler or furnace is required by the directory used to certify product performance, the responsible party certifies by signing below that the installed air handler/furnace matches the equipment specified in the directory. F. Verified Cooling System Time Delay Relay This section does not apply to this project. G. Verified Cooling System TXV This section does not apply to this project. Registration Number: 219-P010089040A-000-001-M26002A-0000 Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CalCERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:28:10 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-26-H Rated Space Conditioning System Equipment Verification (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:20 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:20 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M26002A-0000 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:28:10 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-26-H Rated Space Conditioning System Equipment Verification (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. System Information Procedures for verification of High SEER and EER Equipment are described in Reference Appendix RA3.4. Each HVAC system requ'ring verification must use a separate form. 01 System Name or Identification/Tag System 2 02 System Location or Area Served KITCHEN 03 Status: SEER and EER performance compliance credit check Both SEER and EER HERS Verification is required 04 Directory used to certify product performance AHRI 05 AHRI certification number for the installed space conditioning system from http://www.ahridirectory.org 8224876 06 Does the directory used to certify product performance require a specific air handler/furnace make and model? ir Yes R 5, I 07 Does the directory used to certify product performance require a time delay relay (+TDR)? Now t n c 08 Does the directory used to certify product performance require a TXV (+TXV)? No B. Rated Space Conditioning System Equipment Verification The data on nameplate of the installed component shall conform to the data for the component as shown in the Directory used to certify product performance in order to demonstrate compliance. Data from Nameplate of Installed system component Data from the Directory used to certify product performance for the rated system component Outdoor Condenser or Package Unit - Installed Manufacturer Name 01 GOODMAN 02 GOODMAN Outdoor Condenser or Package Unit - Installed Model Number 03 AVXC200361AE 04 AVXC200361AE Inside Coil - Installed Manufacturer Name 05 US ALUMACOIL 06 ALUMACOIL Inside Coil - Installed Model Number 07 CAPF3743C6DB 08 CAPF3743C6DB Air Handler/Furnace - Installed Manufacturer Name 09 GOODMAN 10 GOODMAN Registration Number: 219-P010089040A-000-001-M26003A-0000 Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CalCERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:32:16 CERTIFICATE OF INSTALLATION CF2R-MCH-26-H Rated Space Conditioning System Equipment Verification (Page 2 of 3) B. Rated Space Conditioning System Equipment Verification The data on nameplate of the installed component shall conform to the data for the component as shown in the Directory used to certify product performance in order to demonstrate compliance. Air Handler/Furnace - Installed Model Number 11 A M VC80805 CXCA 12 AMVC80805CXCA C. Verified Cooling System SEER 01 Required minimum SEER 18 02 Installed SEER 21 03 Compliance Statement: System passes SEER verification Signature by responsible party below certifies that the installed cooling equipment meets or exceeds the required value listed on the CF1R. D. Verified Cooling System EER 01 Required minimum EER N. 13 02 Installed EER — 13 03 Compliance Statement: System passes EER verification Signature by responsible party below certifies that the installed cooling equipment meets or exceeds the required value listed on the CF1R. E. Verified Cooling System Air Handler/Furnace 01 If a specific air handler or furnace is required by the directory used to certify product performance, the responsible party certifies by signing below that the installed air handler/furnace matches the equipment specified in the directory. F. Verified Cooling System Time Delay Relay This section does not apply to this project. G. Verified Cooling System TXV This section does not apply to this project. Registration Number: 219-P010089040A-000-001-M26003A-0000 Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CalCERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:32:16 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-26-H Rated Space Conditioning System Equipment Verification (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:20 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:20 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M26003A-0000 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:32:16 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-26-H Rated Space Conditioning System Equipment Verification (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. System Information Procedures for verification of High SEER and EER Equipment are described in Reference Appendix RA3.4. Each HVAC system requ'ring verification must use a separate form. 01 System Name or Identification/Tag System 3 02 System Location or Area Served MASTER 03 Status: SEER and EER performance compliance credit check Both SEER and EER HERS Verification is required 04 Directory used to certify product performance AHRI 05 AHRI certification number for the installed space conditioning system from http://www.ahridirectory.org 8256560 06 Does the directory used to certify product performance require a specific air handler/furnace make and model? i Yes R 5, I 07 Does the directory used to certify product performance require a time delay relay (+TDR)? Now t nc 08 Does the directory used to certify product performance require a TXV (+TXV)? No B. Rated Space Conditioning System Equipment Verification The data on nameplate of the installed component shall conform to the data for the component as shown in the Directory used to certify product performance in order to demonstrate compliance. Data from Nameplate of Installed system component Data from the Directory used to certify product performance for the rated system component Outdoor Condenser or Package Unit - Installed Manufacturer Name 01 GOODMAN 02 GOODMAN Outdoor Condenser or Package Unit - Installed Model Number 03 AVXC200601AE 04 AVXC200601AE Inside Coil - Installed Manufacturer Name 05 ASPEN 06 ASPEN Inside Coil - Installed Model Number 07 CC60G44245L004 08 CC60G44245L004 Air Handler/Furnace - Installed Manufacturer Name 09 GOODMAN 10 GOODMAN Registration Number: 219-P010089040A-000-001-M26004A-0000 Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CalCERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:34:24 CERTIFICATE OF INSTALLATION CF2R-MCH-26-H Rated Space Conditioning System Equipment Verification (Page 2 of 3) B. Rated Space Conditioning System Equipment Verification The data on nameplate of the installed component shall conform to the data for the component as shown in the Directory used to certify product performance in order to demonstrate compliance. Air Handler/Furnace - Installed Model Number 11 A M VC80805 CXCA 12 AMVC80805CXCA C. Verified Cooling System SEER 01 Required minimum SEER 18 02 Installed SEER 18.85 03 Compliance Statement: System passes SEER verification Signature by responsible party below certifies that the installed cooling equipment meets or exceeds the required value listed on the CF1R. D. Verified Cooling System EER 01 Required minimum EER N. 13 02 Installed EER — 13 03 Compliance Statement: System passes EER verification Signature by responsible party below certifies that the installed cooling equipment meets or exceeds the required value listed on the CF1R. E. Verified Cooling System Air Handler/Furnace 01 If a specific air handler or furnace is required by the directory used to certify product performance, the responsible party certifies by signing below that the installed air handler/furnace matches the equipment specified in the directory. F. Verified Cooling System Time Delay Relay This section does not apply to this project. G. Verified Cooling System TXV This section does not apply to this project. Registration Number: 219-P010089040A-000-001-M26004A-0000 Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CalCERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:34:24 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-26-H Rated Space Conditioning System Equipment Verification (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:20 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:20 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M26004A-0000 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:34:24 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-26-H Rated Space Conditioning System Equipment Verification (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. System Information Procedures for verification of High SEER and EER Equipment are described in Reference Appendix RA3.4. Each HVAC system requ'ring verification must use a separate form. 01 System Name or Identification/Tag System 4 02 System Location or Area Served LOWER OUTSIDE SUITE 03 Status: SEER and EER performance compliance credit check Both SEER and EER HERS Verification is required 04 Directory used to certify product performance AHRI 05 AHRI certification number for the installed space conditioning system from http://www.ahridirectory.org 201851574 06 Does the directory used to certify product performance require a specific air handler/furnace make and model? ir No ic R 5 07 Does the directory used to certify product performance require a time delay relay (+TDR)? Now t , 08 Does the directory used to certify product performance require a TXV (+TXV)? No B. Rated Space Conditioning System Equipment Verification The data on nameplate of the installed component shall conform to the data for the component as shown in the Directory used to certify product performance in order to demonstrate compliance. Data from Nameplate of Installed system component Data from the Directory used to certify product performance for the rated system component Outdoor Condenser or Package Unit - Installed Manufacturer Name 01 DAIKIN 02 DAIKIN Outdoor Condenser or Package Unit - Installed Model Number 03 RX24RMVJU 04 RX24RMVJU Inside Coil - Installed Manufacturer Name 05 DAIKIN 06 DAIKIN Inside Coil - Installed Model Number 07 FDMQ24RVJU 08 FDMQ24RVJU Air Handler/Furnace - Installed Manufacturer Name 09 N/A 10 This field or section is not applicable Registration Number: 219-P010089040A-000-001-M26005A-0000 Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CalCERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:36:34 CERTIFICATE OF INSTALLATION CF2R-MCH-26-H Rated Space Conditioning System Equipment Verification (Page 2 of 3) B. Rated Space Conditioning System Equipment Verification The data on nameplate of the installed component shall conform to the data for the component as shown in the Directory used to certify product performance in order to demonstrate compliance. Air Handler/Furnace - Installed Model Number 11 N/A 12 This field or section is not applicable C. Verified Cooling System SEER 01 Required minimum SEER 16.5 02 Installed SEER 18.6 03 Compliance Statement: System passes SEER verification Signature by responsible party below certifies that the installed cooling equipment meets or exceeds the required value listed on the CF1R. D. Verified Cooling System EER 01 Required minimum EER N. 12.3 02 Installed EER — 12.5 03 Compliance Statement: System passes EER verification Signature by responsible party below certifies that the installed cooling equipment meets or exceeds the required value listed on the CF1R. E. Verified Cooling System Air Handler/Furnace This section does not apply to this project. F. Verified Cooling System Time Delay Relay This section does not apply to this project. G. Verified Cooling System TXV This section does not apply to this project. Registration Number: 219-P010089040A-000-001-M26005A-0000 Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CalCERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:36:34 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-26-H Rated Space Conditioning System Equipment Verification (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:20 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:20 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M26005A-0000 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:36:34 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-26-H Rated Space Conditioning System Equipment Verification (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. System Information Procedures for verification of High SEER and EER Equipment are described in Reference Appendix RA3.4. Each HVAC system requ'ring verification must use a separate form. 01 System Name or Identification/Tag System 5 02 System Location or Area Served LOWER INNER SUITE 03 Status: SEER and EER performance compliance credit check Both SEER and EER HERS Verification is required 04 Directory used to certify product performance AHRI 05 AHRI certification number for the installed space conditioning system from http://www.ahridirectory.org 201851573 06 Does the directory used to certify product performance require a specific air handler/furnace make and model? ir No ic R 5 07 Does the directory used to certify product performance require a time delay relay (+TDR)? Now t , 08 Does the directory used to certify product performance require a TXV (+TXV)? No B. Rated Space Conditioning System Equipment Verification The data on nameplate of the installed component shall conform to the data for the component as shown in the Directory used to certify product performance in order to demonstrate compliance. Data from Nameplate of Installed system component Data from the Directory used to certify product performance for the rated system component Outdoor Condenser or Package Unit - Installed Manufacturer Name 01 DAIKIN 02 DAIKIN Outdoor Condenser or Package Unit - Installed Model Number 03 RX18RMVJU 04 RX18RMVJU Inside Coil - Installed Manufacturer Name 05 DAIKIN 06 DAIKIN Inside Coil - Installed Model Number 07 FDMQ18RVJU 08 FDMQ18RVJU Air Handler/Furnace - Installed Manufacturer Name 09 N/A 10 This field or section is not applicable Registration Number: 219-P010089040A-000-001-M26006A-0000 Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:39:27 CERTIFICATE OF INSTALLATION CF2R-MCH-26-H Rated Space Conditioning System Equipment Verification (Page 2 of 3) B. Rated Space Conditioning System Equipment Verification The data on nameplate of the installed component shall conform to the data for the component as shown in the Directory used to certify product performance in order to demonstrate compliance. Air Handler/Furnace - Installed Model Number 11 N/A 12 This field or section is not applicable C. Verified Cooling System SEER 01 Required minimum SEER 16.5 02 Installed SEER 18.5 03 Compliance Statement: System passes SEER verification Signature by responsible party below certifies that the installed cooling equipment meets or exceeds the required value listed on the CF1R. D. Verified Cooling System EER 01 Required minimum EER N. 12.3 02 Installed EER — 12.5 03 Compliance Statement: System passes EER verification Signature by responsible party below certifies that the installed cooling equipment meets or exceeds the required value listed on the CF1R. E. Verified Cooling System Air Handler/Furnace This section does not apply to this project. F. Verified Cooling System Time Delay Relay This section does not apply to this project. G. Verified Cooling System TXV This section does not apply to this project. Registration Number: 219-P010089040A-000-001-M26006A-0000 Registration Date/Time: 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:39:27 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-26-H Rated Space Conditioning System Equipment Verification (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:20 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:20 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M26006A-0000 2019-04-17 12:19:20 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:39:27 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-26-H Rated Space Conditioning System Equipment Verification (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. System Information Procedures for verification of High SEER and EER Equipment are described in Reference Appendix RA3.4. Each HVAC system requ'ring verification must use a separate form. 01 System Name or Identification/Tag System 6 02 System Location or Area Served UPPER POOL SUITE 03 Status: SEER and EER performance compliance credit check Both SEER and EER HERS Verification is required 04 Directory used to certify product performance AHRI 05 AHRI certification number for the installed space conditioning system from http://www.ahridirectory.org 201851574 06 Does the directory used to certify product performance require a specific air handler/furnace make and model? ir No ic R 5 07 Does the directory used to certify product performance require a time delay relay (+TDR)? Now t , 08 Does the directory used to certify product performance require a TXV (+TXV)? No B. Rated Space Conditioning System Equipment Verification The data on nameplate of the installed component shall conform to the data for the component as shown in the Directory used to certify product performance in order to demonstrate compliance. Data from Nameplate of Installed system component Data from the Directory used to certify product performance for the rated system component Outdoor Condenser or Package Unit - Installed Manufacturer Name 01 DAIKIN 02 DAIKIN Outdoor Condenser or Package Unit - Installed Model Number 03 RX24RMVJU 04 RX24RMVJU Inside Coil - Installed Manufacturer Name 05 DAIKIN 06 DAIKIN Inside Coil - Installed Model Number 07 FDMQ24RVJU 08 FDMQ24RVJU Air Handler/Furnace - Installed Manufacturer Name 09 N/A 10 This field or section is not applicable Registration Number: 219-P010089040A-000-001-M26007A-0000 Registration Date/Time: 2019-04-17 12:19:21 HERS Provider: CalCERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 11:50:18 CERTIFICATE OF INSTALLATION CF2R-MCH-26-H Rated Space Conditioning System Equipment Verification (Page 2 of 3) B. Rated Space Conditioning System Equipment Verification The data on nameplate of the installed component shall conform to the data for the component as shown in the Directory used to certify product performance in order to demonstrate compliance. Air Handler/Furnace - Installed Model Number 11 N/A 12 This field or section is not applicable C. Verified Cooling System SEER 01 Required minimum SEER 16.5 02 Installed SEER 18.6 03 Compliance Statement: System passes SEER verification Signature by responsible party below certifies that the installed cooling equipment meets or exceeds the required value listed on the CF1R. D. Verified Cooling System EER 01 Required minimum EER N. 12.3 02 Installed EER — 12.5 03 Compliance Statement: System passes EER verification Signature by responsible party below certifies that the installed cooling equipment meets or exceeds the required value listed on the CF1R. E. Verified Cooling System Air Handler/Furnace This section does not apply to this project. F. Verified Cooling System Time Delay Relay This section does not apply to this project. G. Verified Cooling System TXV This section does not apply to this project. Registration Number: 219-P010089040A-000-001-M26007A-0000 Registration Date/Time: 2019-04-17 12:19:21 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:50:18 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-26-H Rated Space Conditioning System Equipment Verification (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:21 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:21 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M26007A-0000 2019-04-17 12:19:21 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 11:50:18 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-26-H Rated Space Conditioning System Equipment Verification (Page 1 of 3) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 A. System Information Procedures for verification of High SEER and EER Equipment are described in Reference Appendix RA3.4. Each HVAC system requ'ring verification must use a separate form. 01 System Name or Identification/Tag System 7 02 System Location or Area Served UPPER ENTRY SUITE 03 Status: SEER and EER performance compliance credit check Both SEER and EER HERS Verification is required 04 Directory used to certify product performance AHRI 05 AHRI certification number for the installed space conditioning system from http://www.ahridirectory.org 801851574 06 Does the directory used to certify product performance require a specific air handler/furnace make and model? ir No ic R 5 07 Does the directory used to certify product performance require a time delay relay (+TDR)? Now t , 08 Does the directory used to certify product performance require a TXV (+TXV)? No B. Rated Space Conditioning System Equipment Verification The data on nameplate of the installed component shall conform to the data for the component as shown in the Directory used to certify product performance in order to demonstrate compliance. Data from Nameplate of Installed system component Data from the Directory used to certify product performance for the rated system component Outdoor Condenser or Package Unit - Installed Manufacturer Name 01 DAIKIN 02 DAIKIN Outdoor Condenser or Package Unit - Installed Model Number 03 RX24RMVJU 04 RX24RMVJU Inside Coil - Installed Manufacturer Name 05 DAIKIN 06 DAIKIN Inside Coil - Installed Model Number 07 FDMQ24RVJU 08 FDMQ24RVJU Air Handler/Furnace - Installed Manufacturer Name 09 N/A 10 This field or section is not applicable Registration Number: 219-P010089040A-000-001-M26008A-0000 Registration Date/Time: 2019-04-17 12:19:21 HERS Provider: CalCERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Schema Version: rev 20180426 Report Generated: 2019-04-17 12:17:57 CERTIFICATE OF INSTALLATION CF2R-MCH-26-H Rated Space Conditioning System Equipment Verification (Page 2 of 3) B. Rated Space Conditioning System Equipment Verification The data on nameplate of the installed component shall conform to the data for the component as shown in the Directory used to certify product performance in order to demonstrate compliance. Air Handler/Furnace - Installed Model Number 11 N/A 12 This field or section is not applicable C. Verified Cooling System SEER 01 Required minimum SEER 16.5 02 Installed SEER 18.6 03 Compliance Statement: System passes SEER verification Signature by responsible party below certifies that the installed cooling equipment meets or exceeds the required value listed on the CF1R. D. Verified Cooling System EER 01 Required minimum EER N. 12.3 02 Installed EER — 12.5 03 Compliance Statement: System passes EER verification Signature by responsible party below certifies that the installed cooling equipment meets or exceeds the required value listed on the CF1R. E. Verified Cooling System Air Handler/Furnace This section does not apply to this project. F. Verified Cooling System Time Delay Relay This section does not apply to this project. G. Verified Cooling System TXV This section does not apply to this project. Registration Number: 219-P010089040A-000-001-M26008A-0000 Registration Date/Time: 2019-04-17 12:19:21 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 12:17:57 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-26-H Rated Space Conditioning System Equipment Verification (Page 3 of 3) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:21 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: 79VPIs:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:21 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M26008A-0000 2019-04-17 12:19:21 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 12:17:57 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-27-H Indoor Air Quality and Mechanical Ventilation (Page 1 of 7) Project Name: Via Dona Project Enforcement Agency: Quinta City of La Permit Number: . Dwelling Address: 53034 Via Dona City: La Quinta Zip Code: 92253 Title 24, Part 6, Section 150.0(o) Ventilation for Indoor Air Quality. All dwelling units shall meet the requirements of ANSI/ASHRAE Standard 62.2. Ventilation and Acceptable Indoor Air Quality in Low -Rise Residential Buildings. Equation and table numbering on this form corresponds to the numbering for that information in the published ANSI/SHRAE Standard 62.2-2010. A. Dwelling Mechanical Ventilation - General Information 01 Dwelling unit name Via Dona Project 02 Building Type Single Family 03 Project scope Newly constructed building 04 Total Conditioned Floor Area of Dwelling Unit (For addition projects the conditioned floor area equals existing area plus addition area. ) 5527 _ Number of bedrooms in dwelling unit (For addition projects the number of bedrooms equals the existing bedrooms plus addition bedrooms)'OV 5 is05 I L E R 06 Ventilation Operation Schedule Continuous 07 Whole -Building Ventilation Rate Calculation Method Fan Ventilation Rate Method (4.1.1) 08 Whole Building Ventilation System Type Standalone - Exhaust 09 IAQ Fan Location LAUNDRY Note: Non -dwelling units do not meet the definition for a dwelling unit as defined in Section 100.1(b). Non -dwelling units are not designed to provide independent living facilities and do not provide permanent provisions for living, sleeping, eating, cooking and sanitation. MCH-27a - Continuous Ventilation Airflow - Fan Ventilation Rate Method B. Whole -Building Continuous Ventilation - Fan Ventilation Rate Method A mechanical supply system, exhaust system, or combination thereof shall provide whole -building ventilation with outdoor air each hour at no less than the rate in equation 4.1a. 01 Required Continuous Whole -Building Ventilation Rate (Qfan) 100 02 Installed Continuous Whole -Building Ventilation Rate 121 Registration Number: 219-P010089040A-000-001-M27001A-0000 Registration Date/Time: 2019-04-17 12:19:21 HERS Provider: CaICERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Report Generated: 2019-04-17 12:19:08 Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-27-H Indoor Air Quality and Mechanical Ventilation (Page 2 of 7) C. Compliance Statement 01 Building passes continuous whole -building ventilation rate test Registration Number: 219-P010089040A-000-001-M27001A-0000 CaICERTS, Inc HERS PROVIDER • Registration Date/Time: 2019-04-17 12:19:21 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 12:19:08 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-27-H Indoor Air Quality and Mechanical Ventilation (Page3of7) D. Local Mechanical Exhaust System - Fan selection and duct design criteria for compliance Local mechanical exhaust fans shall be installed in each kitchen and bathroom. Delivered local ventilation rates: • All local ventilation rates have been measured using a flow hood, flow grid, or other airflow measuring device and meet the requirements of 62.2 Tables 5.1 or 5.2. OR • The airflow rating at a pressure of 0.25 in. w.c. of a certified fan is assumed because the local ventilation system duct sizing meets the prescriptive requirements of 62.2 Table 5.3, or manufacturer's design criteria. Table 5.1 Intermittent Local Ventilation Exhaust Airflow Rates Application Airflow Notes Kitchen 100 cfm Vented range hood (including appliance -range hood combinations) required if exhaust fan flow is less than 5 ACH. Bathroom 50 cfm Table 5.2 Continuous Local Ventilation Exhaust Airflow Rates Application Airflow Notes Kitchen 5 ACH Based on Kitchen volume. Bathroom Ulk 20 cfm Table 5.3 _ • Prescriptive Duct Sizing Requirements Duct Type Flex Duct Smooth Duct Fan Rating cfm @ 0.25 in. w.g. 50 80 100 125 50 80 100 125 Maximum Allowable Duct Length (ft) Diameter, (in) Flex Duct Smooth Duct 3 X X X X 5 X X X 4 70 3 X X 105 35 5 X 5 NL 70 35 20 NL 135 85 55 6 NL NL 125 95 NL NL NL 145 7andabove NL NL NL NL NL NL NL NL This table assumes no elbows. Deduct 15 ft of allowable duct length for each turn, elbow, or fitting. Interpolation and extrapolation in 62.2 Table 5.3 is not allowed. For airflow values not listed, use the next higher value. This table is not applicable for airflow > 125 cfm. NL = no limit on duct length of this size. X = not allowed, any length of duct of this size with assumed turns, elbows, fittings will exceed the rated pressure drop. Registration Number: 219-P010089040A-000-001-M27001A-0000 Registration Date/Time: 2019-04-17 12:19:21 HERS Provider: CalCERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 12:19:08 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-27-H Indoor Air Quality and Mechanical Ventilation (Page 4 of 7) E. Other Requirements The items listed below (6.1 through 6.8) correspond to the information given in ASHRAE 62.2 Section 6 "Other Requirements". Refer also to Chapter 4.6 of the Residential Compliance Manual (Section 4.6.5) for information describing these "Other Requirements". The signature of the Responsible Person in the declaration statement below certifies that the building complies with these requirements specified in ASHRAE 62.2 Section 6.1 through 6.9 if applicable. 01 6.1 Transfer Air. Measures shall be taken to minimize air movement across envelope components to occupiable spaces from garages, unconditioned crawl spaces, and unconditioned attics. Supply and balanced ventilation systems shall be designed and constructed to provide ventilation air directly from the outdoors. 02 6.2 Instructions and Labeling. Information on the ventilation design and/or ventilation systems installed, instructions on their proper operation to meet the requirements of this standard, and instructions detailing any required maintenance (similar to that provided for HVAC systems) shall be provided to the owner and the occupant of the dwelling unit. Controls shall be labeled as to their function (unless that function is obvious, such as toilet exhaust fan switches). See Chapter 13 of Guideline 24 2 for information on instructions and labeling. 03 6.3 Clothes Dryers. Clothes dryers shall be exhausted directly to the outdoors 04 6.4 Combustion and Solid -Fuel Burning Appliances. Combustion and solid -fuel burning appliances must be provided with adequate combustion and ventilation air and vented in accordance with manufacturer installation instructions, NFPA 54 ANSI Z223.1, National Fuel Gas Code, NFPA 31, Standard for the Installation of Oil -Burning Equipment, or NFPA 211, Standard for Chimneys, Fireplaces, Vents, and Solid -Fuel Burning Appliances, or other equivalent code acceptable to the building official. Where atmospherically vented combustion appliances or solid -fuel burning appliances are located inside the pressure boundary, the total net exhaust flow of the two largest exhaust fans (not including a summer cooling fan intended to be operated only when windows or other air inlets are open) shall not exceed 15 cfm/100 ft2 (75 Lps/100 m2) of occupiable space when in operation at full capacity. If the designed total net flow exceeds this limit, the net exhaust flow must be reduced by reducing the exhaust flow or providing compensating outdoor airflow. Atmospherically vented combustion appliances do not include direct -vent appliances. 05 6.5 Garages. When an occupiable space adjoins a garage, the design must prevent migration of contaminants to the adjoining occupiable space. Air seal the walls, ceilings, and floors that separate garages from occupiable space. To be considered air sealed, all joints, seams, penetrations, openings between door assemblies and their respective jambs and framing, and other sources of air leakage through wall and ceiling assemblies separating the garage from the residence and its attic area shall be caulked, gasketed, weather stripped, wrapped, or otherwise sealed to limit air movement. Doors between garages and occupiable spaces shall be gasketed or made substantially airtight with weather stripping. 06 6.6 Ventilation Opening Area. Spaces shall have ventilation openings as listed below. Such openings shall meet the requirements of Section 6.8 07 6.7 Minimum Filtration. Mechanical systems that supply air to an occupiable space through ductwork exceeding 10 ft (3 m) in length and through a thermal conditioning component, except evaporative coolers, shall be provided with a filter having a designated minimum efficiency of MERV 6, or better, when tested in accordance with ANSI ASHRAE Standard 52.2, Method of Testing General Ventilation Air -Cleaning Devices for Removal Efficiency by Particle Size, or a minimum Particle Size Efficiency of 50 percent in the 3.0-10 µm range in accordance with AHRI Standard 680, Performance Rating of Residential Air Filter Equipment. The system shall be designed such that all recirculated and mechanically supplied outdoor air is filtered before passing through the thermal conditioning components. The filter shall be located and installed in such a manner as to facilitate access and regular service by the owner. Registration Number: 219-P010089040A-000-001-M27001A-0000 Registration Date/Time: 2019-04-17 12:19:21 HERS Provider: CaICERTS CA Building Energy Efficiency Standards 2016 Residential Compliance Report Version: 2018.0.001 Report Generated: 2019-04-17 12:19:08 Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-27-H Indoor Air Quality and Mechanical Ventilation (Page5of7) E. Other Requirements The items listed below (6.1 through 6.8) correspond to the information given in ASHRAE 62.2 Section 6 "Other Requirements". Refer also to Chapter 4.6 of the Residential Compliance Manual (Section 4.6.5) for information describing these "Other Requirements". The signature of the Responsible Person in the declaration statement below certifies that the building complies with these requirements specified in ASHRAE 62.2 Section 6.1 through 6.9 if applicable. 08 6.8 Air Inlets. Air inlets that are part of the ventilation design shall be located a minimum of 10 ft (3 m) from known sources of contamination such as a stack, vent, exhaust hood, or vehicle exhaust. The intake shall be placed so that entering air is not obstructed by snow, plantings, or other material. Forced air inlets shall be provided with rodent insect screens (mesh not larger than 1/2 inch). 09 6.9 Carbon Monoxide Detectors. A carbon monoxide alarm shall be installed in each dwelling unit in accordance with NFPA 720, Standard for the Installation of Carbon Monoxide (CO) Detection and Warning Equipment 14, and shall be consistent with requirements of applicable laws, codes, and standards. The responsible persons signature on this compliance document affirms that all applicable requirements in this table have been met. F. Air Moving Equipment The items listed below (7.1 through 7.3) correspond to the information given in ASHRAE 62.2 Section 7Air-Moving Equipment. Refer also to Chapter 4.6 of the Residential Compliance Manual (Section 4.6.6) for information describing these requirements in more detail. The signature of the Responsible Person in the declaration statement below certifies that the building complies with these requirements specified in ASHRAE 62.2 Section 7.1 through 7.3 if applicable. 01 7.1 Selection and Installation. Ventilation devices and equipment shall be tested and listed in accordance with specific standards. Installations of systems or equipment shall be carried out in accordance with manufacturers' design requirements and installation instructions. 02 7.2 Sound Ratings for Fans. Ventilation fans shall be rated for sound at no less than the minimum airflow rate required by this standard, as noted below. These sound ratings shall be at a minimum of 0.1 in. w.c. (25 Pa) static pressure. 7.2.1 Whole Building or Continuous Ventilation Fans. These fans shall be rated for sound at a maximum of 1.0 sone. 7.2.2 Intermittent Local Exhaust Fans. Fans used to comply with Section 5.2 shall be rated for sound at a maximum of 3 sone, unless their maximum rated airflow exceeds 400 cfm (200 L/s). (Some exceptions may apply.) 03 7.3 Multibranch Exhaust Ducting. If more than one of the exhaust fans in a dwelling unit shares a common exhaust duct, each fan shall be equipped with a back draft damper to prevent the recirculation of exhaust air from one room to another through the exhaust ducting system. The responsible persons signature on this compliance document affirms that all applicable requirements in this table have been met. Registration Number: 219-P010089040A-000-001-M27001A-0000 Registration Date/Time: 2019-04-17 12:19:21 HERS Provider: CalCERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 12:19:08 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-27-H Indoor Air Quality and Mechanical Ventilation (Page6of7) G. Multifamily Buildings -Other Requirements The items listed below correspond to the information given in ASHRAE 62.2 Section 8 "Multifamily Buildings". Refer also to Chapter 4.6 of the Residential Compliance Manual (Section 4.6.5) for information describing these requirements in more detail. The signature of the Responsible Person in the declaration statement below certifies that the building complies with these requirements specified in ASHRAE 62.2 Section 8, if applicable. 8.2 Whole -Building Mechanical Ventilation. For multifamily buildings, the term "building" in Section 4 refers to a single dwelling unit. 8.4.1 Transfer Air. Measures shall be taken to minimize air movement across envelope components separating dwelling units, including sealing penetrations in the common walls, ceilings, and floors of each unit and by sealing vertical chases adjacent to the units. All doors between dwelling units and common hallways shall be gasketed or made substantially airtight. 8.4.1.1 Compliance. One method of demonstrating compliance with Section 8.4.1 shall be to verify a leakage rate below a maximum of 0.2 cfm/ ft2 (100 Lis per 100 m2) of the dwelling unit envelope area (i.e., the sum of the area of the walls 01 between dwelling units, exterior walls, ceiling and floor) at a test pressure of 50 Pa by a blower door test. The test shall be conducted with the dwelling unit as if it were exposed to outdoor air on all sides, top, and bottom by opening doors and windows of adjacent dwelling units. 8.5.1 Exhaust Ducts. Exhaust fans in separate dwelling units shall not share a common exhaust duct. Exhaust inlets from more than one dwelling unit may be served by a single exhaust fan downstream of all the exhaust inlets if the fan is designated and intended to run continuously or if each inlet is equipped with a back -draft damper to prevent cross -contamination when the fan is not running. 8.5.2 Supply Ducts. Supply outlets to more than one dwelling unit may be served by a single fan upstream of all the supply outlets if the fan is designed and intended to run continuously or if each supply outlet is equipped with a back -draft damper to prevent cross -contamination when the fan is not running. The responsible persons signature on this compliance document affirms that all applicable requirements in this table have been met Registration Number: 219-P010089040A-000-001-M27001A-0000 Registration Date/Time: 2019-04-17 12:19:21 HERS Provider: CalCERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 12:19:08 2016 Residential Compliance Schema Version: rev 20180426 CERTIFICATE OF INSTALLATION CF2R-MCH-27-H Indoor Air Quality and Mechanical Ventilation (Page 7 of 7) Documentation Author's Declaration Statement 1. I certify that this Certificate of Installation documentation is accurate and complete. Documentation Author Name: Herman Paredes Documentation Author Signature: 7L/L 11 l/ pa in 7�%�1f Company: PALOMA AIR CONDITIONING Signature Date: 2019-04-17 12:19:21 Address: 83019 ave 45 CEA/ HERS Certification Identification (if applicable): City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Responsible Person's Declaration statement I certify the following under penalty of perjury, under the laws of the State of California: 1. The information provided on this Certificate of Installation is true and correct. 2. I am either: a) a responsible person eligible under Division 3 of the Business and Professions Code in the applicable classification to accept responsibility for the system design, construction, or installation of features, materials, components, or manufactured devices for the scope of work identified on this Certificate of Installation and attest to the declarations in this statement, or b) I am an authorized representative of the responsible person and attest to the declarations in this statement on the responsible person's behalf. 3. The constructed or installed features, materials, components or manufactured devices (the installation) identified on this Certificate of Installation conforms to all applicable codes and regulations and the installation conforms to the requirements given on the Certificate of Compliance, plans, and specifications approved by the enforcement agency. 4. I understand that a HERS rater will check the installation to verify compliance and if such checking determines the installation fails to comply, I am required to offer any necessary corrective action at no charge to the building owner. 5. I will ensure that a registered copy of this Certificate of Installation shall be posted, or made available with the building permit(s) issued for the building, and made available to the enforcement agency for all applicable inspections. I understand that a registered copy of this Certificate of Installation is required to be included with the documentation the builder provides to the building owner at occupancy. Responsible Builder/Installer Name: Herman Paredes Responsible Builder/Installer Signature: y9VPss:2f!/ Faze Company Name: (Installing Subcontractor or General Contractor or Builder/Owner) PALOMA AIR CONDITIONING Position With Company (Title): OWNER Address: 83019 ave 45 CSLB License: 619091 City/State/Zip: Indio CA 92201 Phone: 760-347-1212 Date Signed: 2019-04-17 12:19:21 Third Party Quality Control Program (TPQCP) Status: Name of TPQCP (if applicable): Digitally signed by CalCERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration Provider responsibility for the accuracy of the information. Registration Number: Registration Date/Time: 219-P010089040A-000-001-M27001A-0000 2019-04-17 12:19:21 HERS Provider: CaICERTS CA Building Energy Efficiency Standards Report Version: 2018.0.001 Report Generated: 2019-04-17 12:19:08 2016 Residential Compliance Schema Version: rev 20180426